Subscribe to Our Youtube Channel
Related Manuals for Wilo Rexa MINI3-V-A Series
Summary of Contents for Wilo Rexa MINI3-V-A Series
- Page 1 Pioneering for You Wilo-Rexa MINI3 en Installation and operating instructions · 3094116 • Ed.02/2021-01...
-
Page 3: Table Of Contents
7 Removal .................................... 13 7.1 Stationary wet well installation.............................. 13 7.2 Portable wet well installation .............................. 13 8 Cleaning .................................... 13 8.1 Clean pump .................................... 14 8.2 Cleaning the pump interior .............................. 14 9 Maintenance .................................... 14 Installation and operating instructions Wilo-Rexa MINI3... - Page 4 9.2 Oil change.................................... 15 9.3 General overhaul .................................. 15 10 Faults, causes and remedies .............................. 15 11 Spare parts.................................... 16 12 Disposal.................................... 16 12.1 Information on the collection of used electrical and electronic products............... 16 12.2 Oil ....................................... 16 WILO SE 2021-01...
-
Page 5: Safety
Children are not allowed to play with (serious) injury! the device. Cleaning and user maintenance CAUTION! ƒ must not be carried out by children without su- Failure to follow the instructions can lead to pervision. potentially irreparable property damage. Installation and operating instructions Wilo-Rexa MINI3... -
Page 6: Fluids Hazardous To Health
Only touch the product by the carrying Ensure sufficient air exchange. – – handle. Wear a breathing protection mask e.g. 3M – Allow product to cool down. Series 6000 with filter 6055 A2 – Clean the device thoroughly. ƒ WILO SE 2021-01... -
Page 7: 1.11 Clean And Disinfect
The staff is trained in the operation of com- ƒ mercial wastewater facilities. The operator is responsible for ensuring that ƒ the product meets the necessary require- ments. Fig. 1: Overview Installation and operating instructions Wilo-Rexa MINI3... -
Page 8: Technical Data
P = with plug Rated power See rating plate ƒ A = with plug and float switch Max. delivery head See rating plate Connection cable length Max. volume flow See rating plate Activation type See rating plate WILO SE 2021-01... -
Page 9: Scope Of Delivery
Maximum: -15 ... +60 °C (5 ... 140 °F), max. humidity: Rexa MINI3-V ... -5M 5 m (16.5 ft) — • 90 %, non-condensing Rexa MINI3-V ... -10M 10 m (33 ft) • • – Recommended: 5 ... 25 °C (41 ... 77 °F), relative hu- Key: midity: 40 … 50 % — = Not permitted, • = Permitted Installation and operating instructions Wilo-Rexa MINI3... -
Page 10: Installation And Electrical Connection
2. Slide the hose clip over the pressure hose. ƒ The pressure pipe must not be smaller than the pump’s 3. Slide the pressure hose onto the hose connection discharge connection. at the pressure port. ƒ Seal pipe connections with Teflon tape. WILO SE 2021-01... -
Page 11: Electrical Connection
The minimum requirement is a thermal relay/motor pro- tection switch with temperature compensation, differ- ential trip and reactivation lock according to local regu- lations. ƒ Install the mains disconnection device! Minimum requirement: Main switch with all-pole discon- nection. Installation and operating instructions Wilo-Rexa MINI3... -
Page 12: Commissioning
NOTICE! If the pump does not switch on once a week, inlet quantity is higher, the pump will not be repeat the test run every month. able to pump away the volume flow. The pump chamber may overflow! WILO SE 2021-01... -
Page 13: During Operation
The protective equipment prevents contact with germs that are hazardous to health and the disinfectant. 3. Disconnect the connection cable from the pressure pipe. ƒ If a disinfectant is used, follow the manufacturer's in- structions! Installation and operating instructions Wilo-Rexa MINI3... -
Page 14: Clean Pump
There is a danger of cuts and – Shell Turbo T 32 similar injuries! Wear protective gloves! In the case of severe dirt and encrustations, remove the cover plate on the suction port and clean the pump in- terior. WILO SE 2021-01... -
Page 15: Oil Change
Faults, causes and remedies ⇒ Shut down the pump, remove it and clean it. 3. Air in the pump/pressure pipe Pump not starting or switches off after a short time 1. Interrupted power supply Installation and operating instructions Wilo-Rexa MINI3... -
Page 16: Spare Parts
Observe the locally applicable regulations! Please consult your local municipality, the nearest waste disposal site, or the dealer who sold the product to you for information on proper disposal. See www.wilo‑recycling.com for more information about re- cycling. WILO SE 2021-01... - Page 20 Local contact at www.wilo.com/contact WILO SE Nortkirchenstr. 100 44263 Dortmund Germany T +49 (0)231 4102-0 T +49 (0)231 4102-7363 wilo@wilo.com Pioneering for You www.wilo.com...
Need help?
Do you have a question about the Rexa MINI3-V-A Series and is the answer not in the manual?
Questions and answers