Globalstar Sat-Fi2 Quick Start Manual page 4

STEP 4: TEST THE SAT-FI2 CONNECTION
Make a satellite call to test and confirm the Sat-Fi2 system is configured and operational.
1. With your device fully charged, go outside where Sat-Fi2 has a 360° clear view of the sky with
no obstructions (buildings, trees, etc.) and power on the Sat-Fi2 (see Figure 2). Ensure
co-located antenna is fully extended in an upright position (see Figure 3).
NOTE: The Sat-Fi2 can take up to 3 to 5 minutes to power on, boot up, and start establishing
a satellite/gateway connection. The Satellite LED will blink RED until the smart device is
connected to the Sat-Fi2 via Wi-Fi and the Sat-Fi2 is registered with a gateway.
2. Open the Sat-Fi2 App and verify that both the
Bar. If the icons are not displayed you may not have a clear view of the sky.
3. In the Application Menu select
4. Enter the telephone number you wish to call, or choose a contact, and select
FIGURE 2
RESTRICTED VIEW
OF THE SKY
MAY NOT FUNCTION PROPERLY
S.O.S.
IMPORTANT NOTICE: S.O.S. MODE SHOULD ONLY BE USED DURING LIFE
THREATENING EMERGENCIES. SENDING FALSE S.O.S. MESSAGES MAY
SUBJECT YOU TO LIABILITY FOR ADDITIONAL CHARGES.
Activate S.O.S. mode to begin communicating and sending alerts directly to GEOS International
Emergency Response Coordination Center (IERCC). GEOS IERCC will notify the appropriate
emergency responders based on the Sat-Fi2's GPS location and your emergency situation.
Responders may include local police, Coast Guard, or Search and Rescue teams. Please note that
you may be liable for expenses related to your rescue if you have not purchased the optional Search
& Rescue benefit. To learn more about GEOS Member Benefits, visit ca.Globalstar.com/GEOS.
NOTE: Sat-Fi2 911/S.O.S. only applies within the designated Sat-Fi2 coverage area. For current
coverage information, please visit: ca.Globalstar.com/Sat-Fi2Support
and icons are displayed on the Status
.
CLEAR VIEW OF THE SKY
CORRECT
INITIATE S.O.S.
1. FROM THE DEVICE: Power on the Sat-Fi2,
lift the protective S.O.S. cover and hold
down the S.O.S. button until the S.O.S. LED
blinks green (see Figure 3).
FROM THE APP: From the Sat-Fi2 App's
Home screen, select
the right and follow the on-screen instruction
(see Figure 4).
NOTE: While S.O.S. is active, the Sat-Fi2 must
remain outside where it has a 360º clear view
of the sky with no obstructions in order to
maintain network connectivity.
.
2. Once S.O.S. is initiated and GEOS IERCC
has received acknowledgment of your
request, the Sat-Fi2 will continuously send
S.O.S. notifications with your GPS position to
GEOS IERCC every 5 minutes until S.O.S. is
canceled or the Sat-Fi2 is powered off.
3. Sat-Fi2 will then enable you to talk or text with
GEOS IERCC via the Sat-Fi2 App.
CANCEL S.O.S.
FROM THE DEVICE: Lift the protective S.O.S.
cover and hold down the S.O.S. button until the
S.O.S. LED blinks red.
FROM THE APP: From the Sat-Fi2 App's S.O.S.
screen, slide the globe to the left and follow the
on-screens instructions (see Figure 5).
Important Note: The Sat-Fi2 will remain
in S.O.S. mode until canceled by the
user. The S.O.S. notification to GEOS will
not be canceled if the device is powered
off or if the Sat-Fi2 App is turned off.
FIGURE 3
, slide the globe to
FIGURE 4
iOS
FIGURE 5
iOS
Android
Android