CTC Union Clatronic AR 737 USB/TFT Instruction Manual & Guarantee page 25

REG OFF: The programme identifi cation (PI) of the regional
programme is ignored during the search for an alternative
frequency (AF) or a programme identifi cation (PI).
• PI MUTE/PI SOUND (only for radio operation)
If you are in an area where two programme identifi cations
(PI) overlap, you can select the option PI SOUND and PI
MUTE for playback of the sound. Alternate switching of the
programme identifi cation should be avoided.
PI SOUND: If switching nevertheless occurs the sound of
another station is heard for less than one second.
PI MUTE: The sound of another station is suppressed.
• AF (Alternative Frequencies)
AF is a function that works with the help of RDS (Radio Data
System) and can only be used with FM stations. The radio
searches in the background for the best frequency reception
of the station that has been tuned into.
AF ON: If the AF function has been switched on, the radio
continuously tests the signal strength of the AF frequency.
The test interval for each AF frequency depends on the
signal strength of the current station and varies from a few
minutes in the case of a strong signal to a few seconds in
the case of weak signals. Whenever the new AF frequency
is stronger than the station that is currently tuned in, the
radio switches to this frequency for a short time and the
message „NEW FREQUENCY" is displayed for one to two
seconds. As the mute time during the frequency change and
the test time is very short, this is almost inaudible during the
normal programme.
NOTE:
The AF function can also be activated by keeping the TA
button (19) pressed down.
The status of the AF function is shown by an AF symbol in
the display.
• If the AF symbol appears in the display, the AF function
is switched on and RDS transmission data is being
received.
• If the AF symbol fl ashes in the display, the AF function
is selected but no RDS signal can be received at the
moment.
AF OFF: The function is switched off. The AF symbol in the
display goes off.
4. EJ Button
Press this button to insert and eject the CD/DVD. The ope-
rating unit swings downwards. Insert the CD/DVD with the
labelled side facing upwards gently into the CD slot until the
device draws in the CD/DVD automatically. The operating
unit automatically swings back to the normal position.
05-AR 737 DVD_GB 25
NOTE:
• Do not place your fi ngers behind the operating unit.
There is a danger of injury when the operating unit
returns to the normal position.
• If you do not insert a CD/DVD the operating unit only
returns to the normal position after a certain time, or
you can press the EJ button again.
5. TFT Display (liquid crystal display)
6. BND button
Press the BND button briefl y to switch between the 3 FM
bands and the 2 MW (medium wave) bands. The designati-
on of the corresponding level - FM1, FM2, FM3, MW1, MW2
- is shown in the TFT.
7./8. / Buttons TUNE, SEEK, TRACK, SKIP UP/DOWN
a) In radio mode: Move the SEL button in the direction of
„ " or „ " in order to set a radio station manually. Keep
the SEL Taste pressed down in the „ " or „ " direction
in order to start the search for a radio station.
b) In CD/DVD, USB mode: If you wish to jump forwards or
backwards press the SEL button briefl y in the „ " or „ "
direction. To wind through the tracks keep the SEL but-
ton pressed in the „ " or „ " direction for approximately
2 seconds. FF X2 appears in the display. Operating the
SEL button again in the „ " or „ " direction for approxi-
mately 2 seconds increases the winding speed. Speeds
of FF X2, FF X4, FF X8 and FF X16 are available. Press
the II button (18) to return to normal playback.
9. MOD Button
Press this button to select the CD/DVD player, AUX IN, radio
mode etc.
10. MU Button (Mute)
Press the MU button to switch off the loudspeakers for a short
period. The word MUTE fl ashes in the display. Press this
button again to cancel the mute function. This function can
also be cancelled by pressing the VOL multifunction button.
11. APS Button (Autostore - Automatic Station Storage)
In radio mode:
a) Memory function:
Move the SEL button in the direction of APS for approxi-
mately 2 seconds to activate automatic station storage.
The radio searches within the current frequency band,
e.g. FM 1, for the strongest signal level until the search
cycle has fi nished. The six strongest stations are then
allocated to the corresponding storage locations. Then
the station of the fi rst storage location is set.
If you would like to search for more stations in the FM
band, press the BND button in order to change to the
FM 2 or FM 3 band. Move the SEL button again in
the direction of APS for approximately 2 seconds to
continue the search.
b) Scan Function:
If the SEL button is moved briefl y in the direction of
APS, the radio briefl y plays all the preset stations of the
frequency band.
25
21.08.2006, 11:50:00 Uhr