Viking 1600A Series Technical Practice page 5

Factory Default Setting: 2 + 3 + 4 + 1 + 1 + 1
Talk/Listen Delay
Call Length
Silence Time Out
Dial Next Number on Ring No Answer
Dial Next Number on Busy
Pulse Dial Speed
Setting A - Talk/Listen Delay
This feature selects switching time between talk and listen modes (VOX switching time). Programmable in incre-
ments of .1 seconds up to a maximum of .9 seconds (Touch Tones 1 - 9). Note: The factory default is .2 seconds.
Setting B - Call Length Time Out
This feature selects the maximum length of time that calls can be connected. Programmable in increments of 1
minute up to a maximum of 9 minutes (Touch Tones 1 - 9). Program 0 in this location to disable the call length time
out, then the 1600A series phone must rely on a CPC signal to hang-up. Note: The factory default is 3 minutes.
Setting C - Silence Time Out
This feature selects the length of time that calls will remain connected without voice activity. Programmable in
increments of 10 seconds up to a maximum of 90 seconds (Touch Tones 1 - 9). To disable the silence time out,
program 0 in this location. Note: The factory default is 40 seconds.
Setting D - Dial the Next Number on Ring No Answer
If enabled and a ring-no-answer is detected, the 1600A series phone will dial the next programmed speed dial num-
ber, and continue to cycle through the emergency numbers until a call is completed. Note: This feature is disabled
in the factory default setting.
Digits
1 or 0 ...................................
2, 3, 4...9 .............................
Setting E - Dial the Next Number on Busy
If enabled and a busy is detected, the 1600A series phone will dial the
next programmed speed dial number, and continue to cycle through
the emergency numbers until a call is completed. Notes: This feature
is disabled in the factory default setting. If the busy signal is interrupt-
ed with a promotional message, contact your central office to have it
removed.
Setting F - Pulse Dialing Rate (Pulses per second)
The 1600A series phone is capable of dialing different pulse speeds.
Note: The factory default setting is 10pps.
G. Voice Announcer Options
The 1600A series phones have a built-in non-volatile digital voice announcer that may be used to identify the location
of the emergency phone call. The 10 seconds of digital record time is recorded remotely from a Touch Tone phone.
Programming options are as follows:
Two Digit Forced Play time {
Repeat Announcement Setting
Settings A and B - Forced Play Time
The 1600A series phone is factory set to automatically start playing the voice announcement after it has determined
the call has been answered. Alternately, the announcement may be programmed to play after a programmed
amount of time, from 1 (enter "01") to 99 seconds after dialing. If the forced play time is used, it is important to allow
enough time for the 1600A series phone to detect ring-no-answer and busy signals when using the redial features.
To set it to play automatically, enter "00" in the forced play time location. Note: The factory default is 00, play auto-
matically.
Dial: A + B + C + D + E + F + # + 1 + 8
Setting D
Disabled
Dials second number after 2, 3, 4...9 rings respectively
(memory location #17)
Dial: A + B + C + D + E + F + # + 1 + 7
Factory Default Setting: 0 + 0 + 0 + 0 + 0 + 0
Sold by:
Toll Free: (877) 892-2666
Digits
1 ..........................................
2 ..........................................
Digits
1 ..........................................
2 ..........................................
Future Use (enter "0")
http://www.TWAcomm.com
Setting E
Disabled
Enabled
Setting F
10 pps
20 pps