Tensioning The Running Belt; Using The Heart Rate Function; Product Specifications - Vision Fitness T600 Manual

TENSIONING THE RUNNING BELT

After placing the treadmill in the position it will be used, the belt must be checked for
proper tension and centering. The belt might need to be adjusted after the first two
hours of use. Temperature, humidity, and use cause the belt to stretch at different rates.
If the belt starts to slip when a user is on it, be sure to follow the directions below.
1) Locate the two hex head bolts on the rear of the treadmill. The bolts are located at each
end of the frame at the back of the treadmill. These bolts adjust the rear belt roller.
Do not adjust until the treadmill is on. This will prevent over tightening of one side.
2) The belt should have equal distance on either side between the frame.
If the belt is touching one side, do not start the treadmill. Turn the bolts
counter clockwise approximately one full turn on each side. Manually center
the belt by pushing the belt from side to side until it is parallel with the
side rails. Tighten the bolts the same amount as when the user loosened
them, approximately one full turn. Inspect the belt for damage.
3) Start the treadmill running belt by pressing the GO buttion. Increase speed to 3
mph (~4.8 kph) and observe the belt position. If it is moving to the right, tighten
the right bolt by turning it clockwise ¼ turn, and loosen the left bolt ¼ turn. If it is
moving to the left, tighten the left bolt by turning it clockwise ¼ turn and loosen the
right ¼ turn. Repeat Step 3 until the belt remains centered for several minutes.
4) Check the tension of the belt. The belt should be very snug. When a person
walks or runs on the belt, it should not hesitate or slip. If this occurs, tighten
the belt by turning both bolts clockwise ¼ turn. Repeat if necessary.
NOTE: Use the orange strip in the lateral position of the side rails as criteria
to confirm the belt is properly centered. It is necessary to adjust the belt
until the edge of the belt is parallel to the orange or white strip.
WARNING!
Do not run belt faster than 3 mph (~4.8 kph) while centering. Keep
fingers, hair and clothing away from belt at all times.
Treadmills equipped with side handrails and front handlebar for user support and emergency
dismount, press emergency button to stop the machine for emergency dismount.
BEFORE USING THE TREADMILL
Perform initial setup and calibrate the treadmill using the auto-calibration
feature found in 'Manager Mode' or 'Engineering Mode'.
NOTES:
• DO NOT stand on the belt while the auto-calibration sequence is in progress.
• DO NOT adjust incline until the initial setup and auto-calibration are completed.
• DO NOT start the treadmill running belt or press any speed buttons
until directed to while tensioning the running belt.
14
TIGHTENS RIGHT SIDE OF ROLLER TIGHTENS LEFT SIDE OF ROLLER
BELT IS TOO FAR TO THE RIGHT SIDE BELT IS TOO FAR TO THE LEFT SIDE
CAUTION!
RISK OF INJURY TO PERSONS
While you are preparing to use the treadmill, do not stand on the belt. Place
your feet on the side rails before starting the treadmill. Start walking on the belt
only after the belt has begun to move. Never start the treadmill at a fast running
speed and attempt to jump on! In case of an emergency, place both hands on the
side arm rests to hold yourself up and place your feet onto the side rails.
USING THE SAFETY KEY
Your treadmill will not start unless the emergency stop button
is reset. Attach the clip end securely to your clothing. This safety
key is designed to cut the power to the treadmill if you should
fall. Check the operation of the safety key every 2 weeks.
WARNING!
Never use the treadmill without securing the safety key clip to your clothing.
Pull on the safety key clip first to make sure it will not come off your clothing.
Only engage reverse belt direction in a supervised environment.
The maximum default belt speed is 2 mph and should
only be changed by an authorized technician.
Your treadmill is capable of reaching high speeds. Always start off using a
slower speed and adjust the speed in small increments to reach a higher
speed level. Never leave the treadmill unattended while it is running.
When not in use turn the on/off switch to off and unplug the power
cord. Make sure to follow the MAINTENANCE schedule in this guide to
maintain optimal performance and prevent premature electronic failure.
Keep your body and head facing forward. Do not attempt to turn around
or look backwards while the treadmill is running. Stop your workout
immediately if you feel pain, faint, dizzy or are short of breath.

USING THE HEART RATE FUNCTION

The heart rate function on this product is not a medical device. While heart rate grips
can provide a relative estimation of your actual heart rate, they should not be relied
on when accurate readings are necessary. Some people, including those in a cardiac
rehab program, may benefit from using an alternate heart rate monitoring system like
a chest or wrist strap. Various factors, including movement of the user, may affect the
accuracy of your heart rate reading. The heart rate reading is intended only as an exercise
aid in determining heart rate trends in general. Please consult your physician.
PULSE GRIPS
Place the palm of your hands directly on the pulse grip. Both hands must grip the sensors for
your heart rate to register. It takes 5 consecutive heart beats (15-20 seconds) for your heart
rate to register. When gripping the pulse grip, do not grip tightly. Holding the grips tightly may
elevate your blood pressure. Keep a loose, cupping hold. You may experience an erratic readout
if consistently holding the pulse grip. Make sure to clean the pulse sensors to ensure proper
contact can be maintained.The pulse grips are designed for pulse sensing purpose only.
WARNING!
Heart rate monitoring systems may be inaccurate. Over exercising may result
in serious injury or death. If you feel faint, stop exercising immediately.

PRODUCT SPECIFICATIONS

Max User Weight
182 kg / 400 lbs.
Product Weight
178 kg / 392 lbs.
Shipping Weight
210 kg /462 lbs.
Overall Dimensions (L x W x H)*
215 x 91 x 154 cm / 85" x 36" x 61"
* Ensure a minimum clearance width of 0.6 meters (24") for access to and passage around
VISION equipment. Please note, 0.91 meters (36") is the ADA recommended clearance width
for individuals in wheelchairs.
15