Electronic Ignition System; Remove/Replace Drawer (On Some Models) - Whirlpool WEG745H0F Owner's Manual

Electronic Ignition System

Initial Lighting and Gas Flame Adjustments
Cooktop and oven burners use electronic igniters in place of
standing pilots. When the cooktop control knob is turned to the
"ignite" position, the system creates a spark to light the burner. All
cooktop burners will spark, but only the burner with the control
knob turned to the "ignite" position will produce a flame. This
sparking continues as long as the control knob is turned to the
"ignite" position.
When the oven control is turned to the desired setting, sparking
occurs and ignites the gas.
Check Operation of Cooktop Burners
Standard Surface Burners
Push in and turn each control knob to the "ignite" position.
The flame should light within 4 seconds. The first time a burner is
lit, it may take longer than 4 seconds to light because of air in the
gas line.
If Burners Do Not Light Properly:
� Turn cooktop control knob to the "OFF" position.
� Check that the range is plugged into a grounded 3-prong
outlet. Check that the circuit breaker has not tripped or the
household fuse has not blown.
� Check that the gas shut-off valves are set to the open position.
� Check that burner caps are properly positioned on burner
bases.
Repeat start-up. If a burner does not light at this point, turn the
control knobs to the "off" position and contact your dealer or
authorized service company for assistance. Please reference the
Quick Start Guide for contact information.
If the cooktop "low" burner flame needs to be adjusted for any of
the burners, see the "Adjust Flame Height" section.
Power Failure
In case of prolonged power failure, the surface burners can be lit
manually. Hold a lit match near a burner, and turn knob
counterclockwise to LITE. After the burner lights, turn knob to
desired setting.
Check Operation of Oven Bake Burner
1. Press BAKE.
2. Press the Start pad.
The oven burner should light within 8 seconds. The first time a
burner is lit, it may take longer than 8 seconds to light because
of air in the gas line.
3. After 2 minutes, open the oven door and check that the oven
is warm.
If Burner Does Not Light Properly:
� Press the Off pad.
� Check that the range is plugged into a grounded 3-prong
outlet. Check that the circuit breaker has not tripped or the
household fuse has not blown.
� Check that the gas shut-off valves are set to the open position.
Repeat steps 1 to 3. If the burner does not light at this point, press
the off pad and contact your dealer or authorized service company
for assistance. Please reference the Quick Start Guide for contact
information.
If the bake burner flame needs to be adjusted, see the "Adjust
Flame Height" section.
Refer to the Quick Start Guide and online Control Guide for proper
operation of the oven controls.
Check Operation of Oven Broil Burner
1. Close the oven door.
2. Press BROIL.
3. Press the Start pad.
The oven burner should light within 8 seconds. The first time a
burner is lit, it may take longer than 8 seconds to light because
of air in the gas line.
4. After 2 minutes, open the oven door and check that the oven
is warm.
If Burner Does Not Light Properly:
� Press the Off pad.
� Check that the range is plugged into a grounded 3 prong
outlet. Check that the circuit breaker has not tripped or the
household fuse has not blown.
� Check that the gas shut-off valves are set to the open position.
Repeat steps 1 to 3. If the burner does not light at this point, press
the Off pad and contact your dealer or authorized service
company for assistance. Please reference the Quick Start Guide
for contact information.
If the broil burner flame needs to be adjusted, see the "Adjust
Flame Height" section.
Refer to the Quick Start Guide and online Control Guide for proper
operation of the oven controls.
Remove/Replace Drawer (On some
models)
Remove all items from inside the baking drawer, warming drawer
or premium storage drawer, and then allow the range to cool
completely before attempting to remove the drawer.
To Remove:
1. Open the drawer to its fully open position.
2. Using a flat-blade screwdriver, gently loosen the drawer from
the glide alignment notch, and then lift up the drawer
alignment tab from the glide.
A. Flat-blade screwdriver
B. Drawer alignment tab
C. Drawer glide notch
3. Repeat Step 2 on the other side. The drawer is no longer
attached to the drawer glides. Using both hands, pick up the
drawer to complete the removal.
17