Table of Contents
Advertisement
OPERATION
Charging the battery pack
NOTE: Remove the battery pack from the charger after it has been fully charged.
NOTE: Battery should be fully charged before first use.
NOTE: Make sure the mains voltage is the same as rating label which is located on the
charger.
1.
Connect the charger to a power supply. Red LED will light up.
2.
To insert the battery pack into the charger, align the raised ribs of the battery pack with
the grooves of the charger then push it in. (Fig. F)
3.
The red LED light of the charger will light up and then the green light flashes during
normal charging.
4.
After charging is complete, the charger light will turn to a solid green light.
5.
Once the battery is fully charged , depress the battery release button and then remove
the battery pack. (Fig. F)
Power indicator (See Fig. G)
This Li-Ion battery pack is equipped with a power indicator which is used to show the battery
pack's remaining charge. Press the power indicator button to check battery charge as picture
showed. The indicator will stay lit for approximately 4 seconds.
To obtain the best life from the battery
1.
Never allow the battery to completely discharge before recharging. The battery pack
should be placed on the charger whenever the battery pack is noticeably running down
or the tool no longer performs a task it previously performed.
2.
Avoid conducting short charges. Make sure that the battery is fully charged each time by
allowing the charger to complete its full charging cycle.
3.
Avoid allowing loose items like screws or nails etc. to be stored with battery packs as
these or similar items can short battery packs and cause a fire or explosion.
4.
Always unplug the charger when not in use and store in a dry and secure place.
5.
Avoid charging or storing your battery in temperatures below 5°C and above 45°C.
6.
After use, allow the battery pack to cool down for approximately 30 minutes before
attempting to recharge.
To insert the battery pack (Fig. H)
1.
Align the groove on the battery pack with the corresponding ribs in the receptacle of the
device.
2.
Insert the battery pack with moderate force until it was locks in to place.
WARNING:
Only use Yard force 20V original battery pack!
To remove the battery pack from the tool (Fig. I)
1.
Press the battery pack release button.
2.
Remove the battery pack from the tool.
24
OPERATION
Switch ON: (Fig. J)
1.
Press the safety lock button with your thumb.
2.
Depress the switch lever. Once the machine has started then release your thumb from
the lock button.
3.
Hold the trigger down, as it will take at least 15 seconds to draw the water from the
source.
NOTE
: Be prepared for the recoil force of the emitted water jet! Ensure that you are standing
firmly and that you are holding decive securely with both hands, otherwise you could injure
yourself or other people.
Switch OFF:
Release the switch trigger.
Operating the AQUAJET
Adjusting rotary handle (Fig. K)
1.
Press and hold down the rotary handle button.
2.
Adjust the handle to your preferred working position and then release the button.
3 in 1 nozzle (Fig. L)
Whilst holding the lance rotate the nozzle to your selected position making sure that the
nozzle is aligned with the lance arrow
WARNING:
( Do not rotate the nozzle when operating
the Aquajet )
Adjusting working pressure: (Fig. M)
There are 2 working pressure settings.
Press the button once or twice to select thepreferred setting (High & low)
Using the brush (Fig. N)
Remove the lance and nozzle.
Align the brush to the main housing and push down firmly and rotate to secure in place
when using the brush it is advised to use the ECO setting pressure to save water.
Using the foam sprayer (Fig. O&P)
Fill the bottle with detergent, using the brands recommended mixture levels
Align the detergent bottle to the main housing and push down and rotate to secure in place.
SOFT
MEDIUM
HARD
25
Advertisement
Table of Contents
