Advertisement
Table of Contents
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Shark Wandvac System WS630 Series
Summary of Contents for Shark Wandvac System WS630 Series
- Page 1 WANDVAC ™ SYSTEM Cordless Vacuum WS630 Series OWNER’S GUIDE...
-
Page 2: Important Safety Instructions
To reduce the risk of fire, electric shock, injury, or property damage: f) Flammable or combustible materials 33. Use only with Shark battery pack (lighter fluid, gasoline, or kerosene) XSBT330. g) Toxic materials (chlorine bleach,... -
Page 3: Li-Ion Battery
Storage PowerFins Floor Nozzle NOTE: The Shark battery, like all lithium-ion batteries, will naturally decrease in capacity over time from the 100% capacity of NOTE: Once the charging post is installed, it can’t be removed. a new battery. s h a r kc l e a n . c o m... - Page 4 CHARGING CHARGING CHARGING WHILE IN STORAGE MODE CHARGING THE HAND VACUUM REMOVING THE BATTERY STORAGE HOOK CONTACTS STORAGE POST CONTACTS UPRIGHT DOCK CHARGING SIDE-BY-SIDE DOCK CHARGING CHARGING HAND VACUUM BATTERY Charge the unit in upright mode by placing it on the Detach the hand vacuum (see below).
-
Page 5: Using Your Vacuum
USING YOUR VACUUM USING YOUR VACUUM CONTROLS CLEANING MODES POWER BOOST MODE UPRIGHT ABOVE-FLOOR WITH HAND VACUUM Press the On/Off button on the handle to turn on For an added boost of power, push and hold the Use the PowerFins floor nozzle for powerful cleaning Detach the hand vacuum to clean above-floor areas. -
Page 6: Maintaining Your Vacuum
MAINTAINING YOUR VACUUM MAINTAINING YOUR VACUUM CLEANING THE DUST CUP AND FILTER EMPTYING THE DUST CUP 1. With the power off, slide the release button 2. Wipe the screen inside the dust cup lightly with a 1. With the dust cup open and the power off, press 2. -
Page 7: Nozzle Maintenance
MAINTAINING YOUR VACUUM MAINTAINING YOUR VACUUM NOZZLE MAINTENANCE CHECKING FOR BLOCKAGES If you run over a hard or sharp object or notice a noise change while vacuuming, check for blockages or objects caught in the brushroll. Checking for Blockages in the Hand vacuum: 1. -
Page 8: Troubleshooting
MAINTAINING YOUR VACUUM ADDITIONAL ACCESSORIES AVAILABLE ON SHARKACCESSORIES.COM TROUBLESHOOTING Crevice Tool WARNING: To reduce the risk of shock and unintended operation, turn off Duster Crevice Tool power and remove the battery before servicing. Upholstery Tool Wide Upholstery Tool Vacuum is not picking up debris. No suction or light suction. Third indicator light on hand vacuum is Pet Multi-Tool solid yellow. -
Page 9: Five (5) Year Limited Warranty
FIVE (5) YEAR LIMITED WARRANTY TWO (2) YEAR LIMITED BATTERY WARRANTY The Five (5) Year Limited Warranty applies to purchases made from authorized retailers of SharkNinja The Two (2) Year VIP Limited Warranty applies to purchases made from authorized retailers of SharkNinja Operating LLC. -
Page 10: Technical Specifications
NOTES REGISTER YOUR PURCHASE registeryourshark.com RECORD THIS INFORMATION TECHNICAL SPECIFICATIONS Model Number: ����������������������������� Voltage: 11.1V Date Code: ��������������������������������� Date of Purchase: ��������������������������� (Keep receipt) Store of Purchase: ��������������������������� TIP: You can find the model and serial numbers on the QR code label on the bottom of the back of the hand vacuum and battery. - Page 11 For SharkNinja U.S. Patent information, visit sharkninja.com/uspatents © 2020 SharkNinja Operating LLC. SHARK is a registered trademark of SharkNinja Operating LLC. WANDVAC is a trademark of SharkNinja Operating LLC. RBRC is a trademark of Rechargeable Battery Recycling Corporation.
Need help?
Do you have a question about the Wandvac System WS630 Series and is the answer not in the manual?
Questions and answers
removing crevice tool from vacuum
To remove the crevice tool from the Shark System WS630 Series vacuum, press the release buttons on both sides of the handle and slide out the accessory.
This answer is automatically generated