Table of Contents
Advertisement
Quick Links
Multimode Spectrum Stabilized Laser Module
Series − Lab Versions
Installation and Operation Manual
Document Number LASER-785-LAB-02-0409
Office:
Ocean Optics, Inc. World Headquarters
830 Douglas Ave., Dunedin, FL, USA 34698
Phone
727.733.2447
Fax
727.733.3962
8 a.m.– 8 p.m. (Mon-Thu), 8 a.m.– 6 p.m. (Fri) EST
E-mail:
Info@OceanOptics.com
Orders@OceanOptics.com
TechSupport@OceanOptics.com (Technical support)
WARNING
(General sales inquiries)
(Questions about orders)
Protective Eye Wear Should Be Worn
When Using This Instrument - Intense
Radiation Present
See Important Safety Notices inside.
Advertisement
Table of Contents
Related Manuals for Halma Ocean Optics LASER-785-IP-LAB
Summary of Contents for Halma Ocean Optics LASER-785-IP-LAB
- Page 1 Multimode Spectrum Stabilized Laser Module Series − Lab Versions Installation and Operation Manual Document Number LASER-785-LAB-02-0409 Office: Ocean Optics, Inc. World Headquarters 830 Douglas Ave., Dunedin, FL, USA 34698 Phone 727.733.2447 727.733.3962 8 a.m.– 8 p.m. (Mon-Thu), 8 a.m.– 6 p.m. (Fri) EST E-mail: Info@OceanOptics.com (General sales inquiries)
- Page 2 Additional Ocean Optics Asia Offices: 666 Gubei Road, Kirin Tower, Suite 601B, Changning District, Shanghai, PRC. 200336 Phone 86.21.5206.8686 86.21.5206.8686 E-Mail Sun.Ling@OceanOptics.com Ocean Optics Europe Sales and Support Center Geograaf 24, 6921 EW DUIVEN, The Netherlands Phone 31-26-3190500 31-26-3190505 Info@OceanOpticsBV.com E-Mail Regional Headquarters Maybachstrasse 11...
- Page 3 Important Safety Notices The Class IIIB laser described here produces a laser emission of 785 nm with output power levels exceeding 350 mW. All models except the –S are designed to be used in a fiber-coupled configuration (-S is designed for SMA coupling); any other configuration may expose the user to hazardous radiation. This laser is safe to operate, provided the user pays attention to all safety warnings: 1.
- Page 4 Important Safety Notices Sources for additional information and assistance on laser safety are the following: Center for Device and Radiological Health Office of Compliance 2098 Gaither Rd. Rockville, MD 20850 Tel: 301 594 4654 Fax: 301 594 4672 Laser Institute of America 12424 Research Parkway, Suite 125 Orlando, FL 32826 Tel: 407 380 1553...
-
Page 5: Table Of Contents
Table of Contents About This Manual ......................iii Document Purpose and Intended Audience................iii Document Summary........................iii Product-Related Documentation ....................iii Upgrades ......................... iii Chapter 1: Introduction ..............1 Overview ......................... 1 Lab Version Models......................2 Features .......................... 2 Package Contents ......................3 Additional Equipment Required .................. - Page 6 Table of Contents LASER-785-LAB-02-0409...
-
Page 7: About This Manual
About This Manual Document Purpose and Intended Audience This document provides you with information to get your laser set up and operating. Document Summary Chapter Description Introduction Contains a list of product features and package Chapter 1: contents. Chapter 2: Provides instructions for setting up and operating the Set-up and Operation laser. - Page 8 About This Manual LASER-785-LAB-02-0409...
-
Page 9: Chapter 1: Introduction
Chapter 1 Introduction Overview The Multimode Spectrum Stabilized Laser Subsystem Series – Lab Versions consists of three models of Lab Version Models). These continuous wave lasers designed specifically for Raman spectroscopy (see laser models feature an internal 350 mW spectrum stabilized laser module that contains an integral Thermo-Electric Cooler (TEC) and thermistor for monitoring the internal temperature of the laser platform. -
Page 10: Lab Version Models
1: Introduction Spectral Output Captured with HR4000 Spectrometer Lab Version Models This document covers the installation and operation of the following laser models: • LASER-785-IP-LAB − 785 nm spectrum stabilized multi-mode laser with > 350mW of fiber- coupled output power •... -
Page 11: Package Contents
1: Introduction • Remote Interlock, Safety Key Lock-out and Emergency shut-off • LED display for output power setting (Models LASER-785-LAB-ADJ and LASER-785-LAB- ADJ-S only) • Output power control dial (Models LASER-785-LAB-ADJ and LASER-785-LAB-ADJ-S only) Package Contents One (1) Ocean Optics Multimode Stabilized Laser One (1) Thermistor One (1) power cord Two (2) Master Power keys... - Page 12 1: Introduction LASER-785-LAB-02-0409...
-
Page 13: Chapter 2: Set-Up And Operation
Chapter 2 Set-up and Operation Overview This section provides instructions for setting up and operating the laser. Read all instructions and warnings carefully before attempting to install and operate your laser. Set-up The laser set-up procedure differs, depending on whether you are going to control the output power automatically via the Internal Preset mode (Model LASER-785-IP-LAB), manually through the unit’s front panel (Models LASER-785-LAB-ADJ and LASER-785-LAB-ADJ-S), or remotely (all models). -
Page 14: Set-Up For Operation In Internal Power Preset Mode
2: Set-up and Operation Set-up for Operation in Internal Power Preset Mode Use these set-up instructions for the Internal Power Preset mode (Model LASER-785-IP-LAB). ► Procedure 1. Make sure that the master Power key is in the vertical (“Off’) position. 2. -
Page 15: Set-Up For Operation To Control Power Through The Front Panel
2: Set-up and Operation Set-up for Operation to Control Power Through the Front Panel Use these set-up instructions when you want to control the laser power through the unit’s front panel (Models LASER-785-LAB-ADJ and LASER-785-LAB-ADJ-S). ► Procedure 1. Make sure that the master Power key is in the vertical (“Off’) position. 2. -
Page 16: Set-Up For Operation In External Power Control Mode
2: Set-up and Operation Set-up for Operation in External Power Control Mode The Model LASER-785-IP-LAB laser is designed for operation in the Internal Power Preset mode and the Models LASER-785-LAB-ADJ and LASER-785-LAB-ADJ-S are designed for operation through their front panel controls. However, the laser provides you with the capability (via an external port on the back panel) of adjusting the power remotely via computer or signal generator in External Power Control mode. -
Page 17: Operation Controlling Power Through The Front Panel
2: Set-up and Operation 2. Push the Laser On switch (on the front panel). The red LED on the front panel lights to indicate that the laser is in operation. The laser turns on approximately 2 seconds after the switch is pressed. -
Page 18: Operation In External Power Control Mode
2: Set-up and Operation Note Note that the switch returns to the center position after you press it. At this point, it can function as a manual reset. 4. In the event of a power interruption, power failure or interlock break, the laser is automatically disabled. -
Page 19: Shutting Down The Laser
2: Set-up and Operation Shutting Down the Laser Use the following procedure when you are finished using the laser and need to shut it down. ► Procedure 1. Push the Laser On toggle switch (on the front panel) to turn the laser off. Make sure that the Laser On LED goes off. - Page 20 2: Set-up and Operation LASER-785-LAB-02-0409...
-
Page 21: Index
Index set-up, 6, 7, 9 models, 2 Control Power Through Front Panel set-up, 7 Controlling Power Through the Front Panel operation, 8 operation, 9 Controlling Power Through the Front Panel, 9 Extarnal Power Control mode, 10 Internal Power Preset mode, 8 document audience, iii purpose, iii... - Page 22 Index LASER-785-LAB-02-0409...