Advertisement
Quick Links
FIELD PROCEDURE FOR POLE MOUNT
(Used With HPCPE, HPLP1, HPLPD1, SP1, HPLP2,
HP2, HPD2, SP2, SPD2, HGSN Antennas)
HPLP1 / HPLPD1
HPCPE
/ SP1
SP2 / SPD2
HP2 / HPD2
40 High Street. – North Andover, MA 01845 USA
Tel (978)459-8800 fax (978)459-3310 / 8814
Email:
sales@radiowaves.com
|
www.radiowaves.com
Advertisement
Related Manuals for RadioWaves HPCPE
Summary of Contents for RadioWaves HPCPE
- Page 1 FIELD PROCEDURE FOR POLE MOUNT (Used With HPCPE, HPLP1, HPLPD1, SP1, HPLP2, HP2, HPD2, SP2, SPD2, HGSN Antennas) HPLP1 / HPLPD1 HPCPE / SP1 SP2 / SPD2 HP2 / HPD2 40 High Street. – North Andover, MA 01845 USA Tel (978)459-8800 fax (978)459-3310 / 8814 Email: sales@radiowaves.com...
- Page 2 Your Pole Mount Kit is shipped to you in one box containing the following components: 1. Antenna assembly 2. Pole Mount Kit Note: Options and accessories are shipped separately and include separate installation guides. Check the packing slip. Tools Required: 1.
- Page 3 Mounting Kit Component identification: Antenna Antenna Hardware Kit Mounting Plate (attaches with associated antenna to hardware mounting plate) Pole Mount Components and hardware Azimuth Adjust Bolt FP103230-1 REV.K Page 3 of 12...
- Page 4 Assembly of the Mount Kit: Assemble the upper and lower pole mounts. Add the Azimuth Adjust Bolt to the lower pole mount. Attach the upper pole mount to top of antenna mounting plate using hardware supplied with plate. Align pin in plate with hole on mount Confirm that the Mount is centered as shown.
- Page 5 . Attach the lower pole mount to opposite side of plate as shown. Align pin in plate Hardware sequence: with hole on mount Flat washer (between mount and rod), bushing (fits inside rod end), flat washer, lock washer, bolt. (Adjustment Nut) Confirm that the Mount is centered as shown.
- Page 6 Completed assembly views. Adjustment nut on top Adjustment nut on bottom bottom Right hand offset Left hand offset FP103230-1 REV.K Page 6 of 12...
- Page 7 FOR SP2/SPD2 UNITS ONLY! In addition to the items listed above, you will receive a “diamond” mount adapter plate with your SP2/SPD2 series antenna. This plate is shipped in the same box as the antenna, and packed with the pole mount. You will need a #2 Phillips screwdriver to install the plate.
- Page 8 Mounting on Pole Fasten the assembled Mount to a maximum 4.5" OD IMPORTANT: Do mounting pipe using not loosen the 4 pole mounts as bolts securing the shown. Position so upper and lower that face of mounting plate is parallel to mounting brackets desired beam path.
- Page 9 While supporting antenna, install (2) 3/8-16 bolts (with washers as shown) through mounting plate and into antenna. Tighten securely. Antenna is now mounted. FP103230-1 REV.K Page 9 of 12...
- Page 10 zimuth Adjustment: Loosen the 4 Azimuth Lock Bolts so mounting plate can move. Caution: Failure to loosen bolts before adjusting will result in damage to mount Adjust mounting plate using eyebolt adjustment nuts to drive antenna to required location. Monitor RCL (Receive Carrier Level) and adjust per radio manufacturer’s instructions.
- Page 11 Elevation adjustment: 1. Loosen (2) Antenna Mounting Bolts slightly so antenna is able to move. Loosening bolts excessively will cause difficulty during adjustment. Caution: Failure to loosen bolts before adjusting will result in damage to mount 2. Rotate Elevation Adjustment Nut as required to set elevation.
-
Page 12: Safety Information
SAFETY INFORMATION This Information May Save You From Death or Injury Do not attempt to install or dismantle any Radio Waves Inc. products until you have read and understood the information and instructions in this document. Installations: Only trained professional installers should be used to install or dismantle antennas, mounts, and related hardware.