Download
Share
Print this page
Parsec Technologies LABRADOR Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Parsec Technologies Manuals
  4. Antenna
  5. LABRADOR
  6. Installation instructions manual

Parsec Technologies LABRADOR Installation Instructions Manual

Hide thumbs
1
2
3
4
5
6
7

Advertisement

Quick Links

Download this manual
LABRADOR
Installation Instructions
Parsec's Labrador is a compact two-in one MIMO LTE external
antenna. This unobtrusive omnidirectional antenna works on
all the common North American LTE bands with high efficiency.
The Labrador is optimized for attachment to a sheetrock wall in
an office environment. It is ideally suited to indoor applications
where a higher performance alternative to screw on antennas is
required. The Labrador has an IP65 ingress protection rating and
may also be mounted outdoors.
CHOOSING THE BEST METHOD AND LOCATION FOR INSTALLATION
To get the best signal, your antenna must be mounted in an isolated area. It is important
to stay away from any interference including existing antennas, cluttered areas, or other
Labrador Pole Mounted
Make sure the antenna is at least 2 feet away from other antennas. Other Antennas
typically need to be 5 feet away.
Heating units, or anything with an electrical motor.
radio interference and reduce antenna performance.
situations that might interupt network.
CAUTION:
Antennas MUST be away from Outlets, AC or
Labrador Wall Mounted
All of these items can cause

Advertisement

loading

Related Manuals for Parsec Technologies LABRADOR

Summary of Contents for Parsec Technologies LABRADOR

  • Page 1 This unobtrusive omnidirectional antenna works on all the common North American LTE bands with high efficiency. The Labrador is optimized for attachment to a sheetrock wall in an office environment. It is ideally suited to indoor applications where a higher performance alternative to screw on antennas is required.

  • Page 2: Assembling The Antenna

    REQUIRED TOOLS Hammer / Rubber Mallet Phillips Screwdriver Drill Assembling the Antenna Assemble the mounting bracket on the antenna using the four plastic thread forming screws. (Figure 1) FIGURE 1...

  • Page 3: Mounting Options

    Mast Mounting (Included) Using the included clamp saddle, v clamp bolt, and nuts and washers you can mount the Labrador on a pole for better isolation. Wall Mounting Instructions Step 1. Mark the position of the screw holes on the wall to mount the antenna on the wall. (Figure 2) FIGURE 2 Step 2.

  • Page 4: Pole Mounting Instructions

    Step 3. Align the mounting hole on the antenna to the wall mounting holes and fasten it to the wall using two screws provided in the kit. (Figure 4) FIGURE 4 Pole Mounting Instructions Step 1. The mast/pole should be a diameter of between 1 and 2.5” to mount the antenna. (Figure 5) Step 2.

  • Page 5: Routing The Cables

    Step 3. Tighten the 2 nuts with your fingers, making sure equal lengths of threads extend past the nuts. Step 4. Use a 7/16 in. wrench to tighten each nut one full turn beyond finger tight to compress the lock washers. (Figure 7) FIGURE 7 Step 5.

  • Page 6: Cable Connection Instructions

    Cable Connection Instructions Note: SMA connectors have a maximum torque of 3-5 inch lbs. Cables on the antenna are labeled as follows, LTE-1 & LTE-2 N-Type SMA Type Step 1. Clean the connectors such that there is no dust in the terminals. Step 2.
  • Page 7 Connect Cellular/ LTE & WLAN cables or stow unused pigtails. Part Number and Included Hardware Cable Kit: PC2402L40NFSM (REQUIRED - PURCHASED SEPRARATELY) Mounting Hardware: Cable Type: LMR200 Connectors : N-Type or SMA Cable Labels: LTE-1 & LTE-2 Parsec Technologies 972-804-4600 support@parsec-t.com Last Revised: 3.9.2021...