Britax Baby Seat Verve User Manual

1 Removing or re-fitting your seat unit
(the seat cover must be removed before fitting the infant carrier)
1a 1b
A
B
HANDY HINT - HANDY HINT - Unfasten the hook and
loop fastenings and
You may find it easier You may find it easier
press studs shown by
to apply the brake to stand behind or to
the red circles
before removing or the side of the buggy.
(dia 1c).
re-fitting the seat unit.
Remove the hood
Please refer to the user
and bumper bar
guide for your buggy for
by simultaneously
operation of the brake.
pressing the buttons on
Unfasten the press the mouldings on both
studs on the backrest sides of the buggy and
A
and unfasten the hook slide them upwards
and loop fastenings on until they disengage
both sides of the seat (dia 1b).
unit where it overlaps
the hood (dia 1a).
B
2 Attaching your child seat for use as a travel system
(this vehicle is intended for children from birth and up to 13kgs)
2a 2b
HANDY HINT -
To fit the adaptor to the
child seat squeeze the
You may find it easier
lever and insert into
to apply the brake
the space below the
when fitting the child
handle (dia 2b). Make
seat. Please refer to
sure it is fully fitted and
the user guide for your
release the lever to
buggy.
lock into place. Repeat
Clip the socket onto
this process for both
the chassis from the
adaptors.
inside. Align the bottom
Ensure that the left
edge of the socket with
hand and right hand
the edge shown on
adaptors are used on
the chassis (dia 2a).
the correct side of the
Rotate the fixing arm.
child seat.
Squeeze the housing
and fixing arm together IMPORTANT -
with one hand and
The buggy seat unit
snap over the hook
must be removed
with the other hand.
before attaching your
Repeat this process for
car seat.
both sockets.
Ensure that the left
hand and right hand
sockets are used on
the correct side of the
buggy.
Only use a P-Type child seat on this buggy when fitted with a Verve P-Type socket
BBO-662-00
1282.000 - Verve Adaptors & Sock1 1
1c 1d 1e
Unclip the hooks on Remove the seat unit
both sides of the buggy from the chassis by
(dia 1d). sliding the base tabs
upwards and out of the
grooves.
Then slide the top tabs
upwards and out of the
grooves until the seat
unit is disengaged
(dia 1e).
To re-fit the seat
unit reverse these
instructions.
2c 2d 2e
To remove the child IMPORTANT -
Lower the child seat
onto the buggy making seat move the handle
It may be necessary to
sure that the adaptor to the carrying position.
remove the adaptors
on either side drops Lift the lever on the
from the child seat
into both the sockets on adaptors and lift the
when installing it in
each side of the buggy child seat out of the
your vehicle.
sockets (dia 2d).
(dia 2c). Push down
If the adaptors are in
firmly. Once the seat is
contact with the vehicle
engaged you will hear
seat cushion, remove
a click.
them.
Move the handle to
To remove the
the rocking position.
adaptors from the child
Please refer to the user
seat, pull the lever on
guide for the child seat.
the adaptors away from
WARNING -
the child seat while
Check that the child pulling down (dia 2e).
seat attachment Repeat the process for
devices are correctly both adaptors.
engaged before use.
The child seat is
IMPORTANT - compatible with
the ISOFIX base
Ensure your child is
(purchased separately).
harnessed at all times.
See www.britax.eu for
further information.
B
B
A
A
User Guide
UK
Verve P-Type
adaptor
Verve P-Type
socket
10/1/07 09:15:40