Inalto AIH60W User Manual page 9

hood
–
Installing the rangehood
Installation heights
– Over gas and electric cookers, Residentia Group recommends our
rangehoods to be mounted at a height of between 600-800mm above the
Through your wall
–
cooking surface.
–
– Electric cooktops must have a minimum height of 600mm from the
–
underside of the rangehood to the cooktop face.
– Gas cooktops must have a minimum of 650mm from the burner to the
–
underside of the rangedhood.
– Over open flame grillers or barbecues, the Gas Regulations require the
filters of the rangehood to be at least 1200mm above the cooking surface.
Pic A
– Determine your installation height , drill 3 holes to install the wall bracket
Cabinet
Positioning the rangehood
with 3 x Wall Plugs and 3 x Screw ST4x30mm onto the wall ensuring that
it is secured in a level position . (SEE Pic A)
– When finish, hang the hood onto the hook
Holes on wall
* S crew*
– Attach the extensible 200mm tube to the hood.
(ST4 x 30mm)
Wall plug
–
Fix the chimney bracket with the chimney with 2 x Screw ST4x8mm
Wall bracket
(SEE Pic C)
– Attached the chimney to the hood , mark and drill 2 holes to fix
the bracket on the wall
Pic D
Important! . if you need the safety screws fixed into the hood,please mark ,
Installing the rangehood
drill and tighten the hood with screw plug and screw(ST4mm X 30mm),you
will need to remove the grease filters first.( See Pic E )
Screw
wall
(ST4 x 30mm)
g
Pic A
ket
Cabinet
c D
* S crew*
(ST4 x 30mm)
Warning: Failure to install the screws or fixing device in accordance
with these instructions may result in electrical hazards.
The warning shall be in the same part of the instructions that include
details of how to mount the equipment.
Determine your installation height , drill 3 holes to install the wall bracket
with 3 x Wall Plugs and 3 x Screw ST4x30mm onto the wall ensuring that
it is secured in a level position . (SEE Pic A)
Further to your various ducting options, below are some tips on how to
When finish, hang the hood onto the hook
correctly duct your rangehood:
Attach the extensible 200mm tube to the hood.
– Always use correctly sized ducting – DO NOT reduce the size of the ducting
Fix the chimney bracket with the chimney with 2 x Screw ST4x8mm
– Always use solid ducting
– Always use non-flammable ducting
(SEE Pic C)
– Always duct to the outside atmosphere
Attached the chimney to the hood , mark and drill 2 holes to fix
– Do not use flexible ducting
the bracket on the wall .
– Do not duct into the ceiling space- always vent to the outside atmosphere.
– Avoid sharp 90 degree bends as much as possible, use 45 degree bends
Important! . if you need the safety screws fixed into the hood,please mark ,
drill and tighten the hood with screw plug and screw(ST4mm X 30mm),you
– Duct to the outside atmosphere using the shortest duct run possible
will need to remove the grease filters first.( See Pic E )
– Use cylindrical ducting whenever possible
Installation heights
– Over gas and electric cookers, Residentia Group recommends our
Screw
(ST4 x 30mm)
– Electric cooktops must have a minimum height of 600mm from the
Holes on wall
Wall plug
– Gas cooktops must have a minimum of 650mm from the burner to the
Wall bracket
– Over open flame grillers or barbecues, the Gas Regulations require the
. (SEE Pic D)
MM
2×
2 2 2 2 W all plug
–
MM
–
Pic B
–
–
2×
(ST4 x 30mm)
–
Exhaust pipe
Cooker hood
Warning: Failure to install the screws or fixing device in accordance
with these instructions may result in electrical hazards.
The warning shall be in the same part of the instructions that include
details of how to mount the equipment.
2× Holes on wall
2 2 2 2 W all plug
Wall plug
Wall bracket
Pic D
2×
* S crew*
MM
MM
(ST4 x 30mm)
Determine your installation height , drill 3 holes to install the w
–
with 3 x Wall Plugs and 3 x Screw ST4x30mm onto the wall e
it is secured in a level position . (SEE Pic A)
. (SEE Pic A)
–
When finish, hang the hood onto the hook
Attach the extensible 200mm tube to the hood.
–
–
Fix the chimney bracket with the chimney with 2 x Screw ST4
(SEE Pic C)
– Attached the chimney to the hood , mark and drill 2 holes to
(SEE Pic D)
the bracket on the wall
Important! . if you need the safety screws fixed into the hood
instead wherever possible
drill and tighten the hood with screw plug and screw(ST4mm
will need to remove the grease filters first.( See Pic E )
Pic B
rangehoods to be mounted at a height of between 600-800mm above the
. (SEE Pic A)
cooking surface.
Exhaust pipe
Screw
(SEE Pic B)
(ST4 x 30mm)
underside of the rangehood to the cooktop face.
underside of the rangedhood.
Cooker hood
filters of the rangehood to be at least 1200mm above the cooking surface.
Pic E
Pic D
Determine your installation height , drill 3 holes to install the wall bracket
with 3 x Wall Plugs and 3 x Screw ST4x30mm onto the wall ensuring that
it is secured in a level position . (SEE Pic A)
When finish, hang the hood onto the hook
Pic C
Attach the extensible 200mm tube to the hood.
Fix the chimney bracket with the chimney with 2 x Screw ST4x8mm
* S crew*
(SEE Pic C)
Attached the chimney to the hood , mark and drill 2 holes to fix
the bracket on the wall . (SEE Pic D)
Important! . if you need the safety screws fixed into the hood,please mark ,
drill and tighten the hood with screw plug and screw(ST4mm X 30mm),you
will need to remove the grease filters first.( See Pic E )
Warning: Failure to install the screws or fixing device in accord
Pic B
with these instructions may result in electrical hazards.
Pic E
The warning shall be in the same part of the instructions that i
Screw
Exhaust pipe
(ST4 x 30mm)
details of how to mount the equipment.
Cooker hood
2× 2 2 2 2 W all plug
2×
* S crew*
(ST4 x 30mm)
Warning: Failure to install the screws or fixing device in accordance
with these instructions may result in electrical hazards.
The warning shall be in the same part of the instructions that include
details of how to mount the equipment.
9
(SEE Pic B)
. (SEE Pic D)
Pic C
Pic B
Exhaust pipe
Cooker hood
2× 2 2 2 2 W all plug
. (SEE Pic A)
(SEE Pic B)
2×
* S crew*
(ST4 x 30mm)
2×
* S crew*
(ST4 x 8mm)
(ST4 x 30mm)
Pic C
Pic E
2×
* S crew*
(ST4 x 30mm)
. (SEE Pic A)
(SEE Pic B)
Pic C
* S crew*
(ST4 x 8mm)
Pic E
* S crew*
* S crew*
(ST4 x 8mm)
2×
* S crew*
(ST4 x 30mm)