Advertisement
Turn "OFF" hot and cold water supplies,
then rotate handle counterclockwise until
the lever points up to relieve pressure.
Remove handle parts.
1. For handle style A & B , remove handle insert
or plug button. Take out handle screw, remove
handle and washer. For handle style C ,
remove cap screw and handle,
then remove handle screw and adapter
2. Remove temperature limit stop, key stop and
stop tube. Lift out retainer clip. Rotate cartridge
shell between the eleven and one o'clock posi-
tions, grasp the cartridge stem with pliers and
pull out cartridge.
Reassembly
Orient cartridge, see illustration on previous page,
then re-insert cartridge by pushing it into the body
until the cartridge ears are flush and aligned with
the top and bottom of the valve body. Replace the
retainer clip with the legs straddling the cartridge
ears. Slide down into the bottom slot. This prevents
rotation and locks the cartridge into the body.
Reinstall stop tube and parts. Limit stop must be
installed with
offset at TOP (12 o'clock) position for maximum hot
water. The notched flat on the stem must point
DOWN when mounting the handle.
TEMPERATURE
KEY STOP
LIMIT STOP
To Adjust Temperature
Limit Stops
CAUTION: Due to season temperature change of
the cold water supply, the temperature limit must
be readjusted accordingly to maintain the desired
maximum discharge temperature.
1. Rotate the handle counterclockwise to stop and
let water run till cold water is purged, check
temperature.
2. Rotate handle to off, remove handle parts (see
Disassembly) and temperature limit stop, rotate
clockwise to decrease and
H H e e l l p p l l i i n n e e
Call our toll free helpline number:
1 (800) 289-6 6 3 6
1 (800) BUY-MOEN
For answers to any product, installation replace-
ment parts, or warranty questions.
Hours of operation are:
8:00 A.M. - 8 P.M. EST. Monday - Friday
8: A.M. - 6:30 P.M. EST. Saturday
counterclockwise to increase maximum
hot water temperature, reinstall temperature
limit stop and handle (TIP: Do not screw
handle in until desired maximum
temperature is achieved)
3. Repeat steps until desired maximum
temperature is achieved.
SHOWERHEAD
TEMPERATURE
LIMIT STOP
ESCUTCHEON
SCREWS (2)
SPOUT
Trim
MAKE SURE ALL WATER SUPPLIES ARE OFF TO
INSTALL TRIM AFTER ROUGH-IN
ROTATE LIMIT
1. Slide the flange into the long end of the show-
STOP CLOCKWISE
TO REDUCE
FULL HOT POSITION
er arm, wrap both ends of the shower arm with
teflon tape and screw long end into pipe ell
inside the wall. Do not install shower head at
this time.
2. Install tub spout
(see spout installation instructions).
3. Remove screw holding plaster ground
and stop tube guard in place and discard. Tem-
porarily install handle. Turn water on, divert
water to tub spout and flush the shower riser
for 15 seconds. Install shower head and check
for leaks. If there are no leaks, turn off and
remove handle and limit stop
4. Install escutcheon plate with 2 screws provid-
ed. Mount with the escutcheon notch up.
5. Install temperature limit stops (see Temperature
Limit Stop section) ensure that notched flat on the
cartridge stem points DOWN.
7:30 A.M. - 5:00 P.M. EST. Monday - Friday
7:30 A.M. - 5:00 P.M. EST. Monday - Friday
Visit our website at www.moen.com for more information
PIPE ELL
SHOWER ARM
NOTCH
CC
CONNECTIONS
ESCUTCHEON
TUB LOOKOUT NIPPLE
In Canada:
1-800-465-6130
Hours of operation are :
Toronto:
1-905-829-3400
Hours of operation are :
Handle Attachment :
For handle style A & B : Mount handle on stem
and replace handle screw tightly. Snap handle
insert or plug button in place.
For handle style C : Mount handle adapter on stem
and replace handle screw tightly. Mount handle on
adapter and replace set screw.
Not for use with Moentrol valves
TO REMOVE STOP VALVE
Always turn water supply OFF before
disassembly (see Disassembly).
Removal of stop valve:
1. Remove handle parts (see Disassembly)
and escutcheon.
2. Using snap ring pliers, remove
retaining ring from valve body.
3. Grip stop valve stem with pliers and
rotate slightly to remove from valve body.
Re-Installation of new stop valve:
1. Check to be sure that stop valve
stem is fully seated in plug.
2. Insert stop valve until fully seated
beyond retaining ring groove in valve body.
3. Using snap ring pliers, place retaining
ring in valve body, making sure that ring
is fully seated.
4. Check orientation of stop valve for water flow.
(Stop is in the off position when
screwdriver slot is vertical).
5. Turn on water supply.
To Eliminate Cross-Piping On
Back-To-Back Installations, or
To Correct Reversed Rough-In Where
Hot and Cold Positions
Are Reversed:
Remove cartridge assembly, rotate 180° and
re-install. (See Reassembly) Caution: Make sure
notch on stem is point up.
In Mexico:
(84) 88-08-26, 88-08-27,
o 91-800-84345
Hours of operation are :
8:00 A.M. - 8 P.M. EST. Monday - Friday
8: A.M. - 6:30 P.M. EST. Saturday
.
2
Advertisement
