Residual Risks; Technical Data - Scheppach DP16SL Translation Of Original Operating Manual

19. Check the tool for damage
Before using the tool, safety devices and any
slightly damaged parts must be carefully checked
to ensure that they are in good working order. Vis-
ually examine the tool's power cable on a regular
basis. All parts must be correctly assembled and
meet all the conditions required to ensure proper
operation.
Unless otherwise specified in the operating in-
structions, any damaged safety devices and parts
must be properly repaired or replaced by a pro-
fessionally recognized workshop. Never use tools
with defective On/Off switches.
20. Warning! Using any plug-in tools and accessories
other than those specified in these operating in-
structions can lead to injury.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from acci-
dents using suitable precautionary measures!
• Do not look directly into the laser beam with unpro-
tected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting sur-
faces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
• Caution - methods other than those specified here
can result in dangerous radiation exposure.
• Never open the laser module. Unexpected expo-
sure to the beam can occur.
• If the drill press is not used for an extended period
of time, the batteries should be removed.
• The laser may not be replaced with a different type
of laser.
• Repairs of the laser may only be carried out by the
laser manufacturer or an authorised representative.

6. Residual risks

The machine has been built using modern technol-
ogy in accordance with recognized safety rules.
Some remaining hazards, however, may still exist.
• Long hair and loose clothing can be hazardous when
the work piece is rotating. Wear personal protective
gear such as a hair net and tight fitting work cothes.
• Wood chips and saw dust can be health hazard. Be
sure to wear personal protective gear such as safe-
ty goggles and a dust mask. Use a vacuum exhaust
system.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Thrown work pieces can lead to injury if the work
piece is not properly secured or fed, such as work-
ing without a limit stop.
• The use of incorrect or damaged mains cables can
lead to injuries caused by electricity.
• Even when all safety measures are taken, some re-
maining hazards which are not yet evident may still
be present.
• Remaining hazards can be minimised by following
the instructions in „safety precautions", „proper use"
and in the entire operating manual.
Keep this safety information in a safe place.

7. Technical data

Dimensions L x B x H mm
Chuck size mm
Spindle cone seat
Drilling chuck cone seat
Drilling chuck clamping range mm
Spindle rise and fall range mm
Chuck to worktable mm
Spindle base working range mm
ø Column mm
Weight kg
Drive
Rated voltage V/Hz
Power rating
Speeds 1/min
Subject to technical modifications!
Load factor:
A load factor of S2 10 min (intermittent periodic duty)
means that you may operate the motor continuously
at its nominal power level (550 W) for no longer than
10 minutes ON period. If you fail to observe this time
limit the motor will overheat. During the OFF period
the motor will cool again to its starting temperature.
Noise
Sound values were measured in accordance with
EN 61029.
Sound pressure level L ...............................57 dB(A)
pA
Uncertainty K ....................................................3 dB
pA
Sound power level L ................................70,5 dB(A)
WA
Uncertainty K ...................................................3 dB
WA
Limit the noise to a minimum!
• Only use appliances which are in perfect working
order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
235x482x732
16
B16
B16
3 - 16
50
305
405
48
23
230/50
550 W
S2 10 min
510 / 800 /
1300 /
1800 / 2450
25 / 60