Advertisement
'68 Custom Princeton
®
Reverb
(This is the model name for warranty claims)
p/n 227-2000-000 (120V)
SERVICE MANUAL
ATTENTION:
WARRANTY SERVICE PROCEDURES
®
The '68 Custom Princeton
Reverb Amplifier is considered to be field serviceable to the
component level. As such stuffed PCB Assemblies are not readily available for this unit.
Any Fender Authorized Service Center in need of a warranty replacement PCB Assembly
for this unit, should contact the Fender Customer Service Call Center, and ask to speak to
an Electronic Technician. You will be given instructions on how to proceed with the repair at
that time. You can reach the Call Center by phone at (866) 345-3642 or by email at
service@fender.com.
Fender Musical Instruments Corporation, 17600 North Perimeter Drive, Suite 100 Scottsdale, AZ 85255
Issued: October, 2013
Advertisement
Table of Contents
Related Manuals for Fender 68 Custom Princeton Reverb
Summary of Contents for Fender 68 Custom Princeton Reverb
- Page 1 Any Fender Authorized Service Center in need of a warranty replacement PCB Assembly for this unit, should contact the Fender Customer Service Call Center, and ask to speak to an Electronic Technician. You will be given instructions on how to proceed with the repair at that time.
-
Page 2: Important Notice
Musical Instruments Corporation. It is not to Corporation. be sold or assigned to another party and is dis- closed solely for use by Fender Authorized Parts marked with two asterisks ( Service Centers for purposes of product service ) indicate the and maintenance. -
Page 3: Specifications
68 Custom Princeton Reverb Release Number: PR 722 Part Numbers 68 CUSTOM PRINCETON REVERB 120V 227-2000-000 68 CUSTOM PRINCETON REVERB 110V TW 227-2001-000 68 CUSTOM PRINCETON REVERB 240V AUS 227-2003-000 68 CUSTOM PRINCETON REVERB 230V UK 227-2004-000 68 CUSTOM PRINCETON REVERB 230V ARG... -
Page 4: Service Notes
C20/R16. The oscillator rate is controlled by Information is focused for its effective use while SPEED control R21 in the first leg of the phase shift maintaining the security of Fender® proprietary in- network. The rate is approximately from 0.5 Hz to 5 formation wherever possible. - Page 5 ® ‘68 Custom Princeton Reverb (This is the model name for warranty claims) POWER SUPPLY diode. A 6.3VAC secondary powers the power indi- cator lamp and the preamp & power amp tubes’ The line voltage is fed to T2’s primary through the heaters.
-
Page 6: Parts List
+ * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department. ** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part. shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above. -
Page 7: Chassis Assembly
+ * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department. ** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part. shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above. - Page 8 + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department. ** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part. shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.
- Page 9 + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department. ** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part. shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.
- Page 10 ® ‘68 Custom Princeton Reverb (This is the model name for warranty claims) Service Diagram List Service Diagram (Schematic)….…..68 CUSTOM PRINCETON REVERB PCB Service Diagram (PCB Assembly)...68 CUSTOM PRINCETON REVERB PCB...