Advertisement
Quick Links
How to Assemble Your Tower Bracket Retrofit Kit
IMPORTANT:
This is a relatively complex installation procedure. It involves drilling holes into the Reformer frame. Please read through these
instructions before proceeding. If you are uncomfortable undertaking any part of this procedure, it is highly recommended that
someone with a serviceable knowledge of equipment assembly and tools install the bracket.
Balanced Body is not responsible for any damage caused by
incorrect assembly.
BEFORE BEGINNING ASSEMBLY
These instructions include a parts list. Please use this list to make
sure you have all the parts necessary for installation. If you are
missing a part, please contact our customer service department
at 1-800-PILATES (1-800-745-2837).
Note: If you have ordered a Tower bracket kit for a Reformer with
casters, refer to Appendix II for additional instructions.
If you had your frame Pre-drilled by the factory remove ALL
hardware installed into the holes used for the tower bracket and
angle brackets. The hardware removed is no longer needed.
REQUIRED TOOLS (NOT INCLUDED)
» Hammer
» Power drill
» Socket wrench with 7/16" and 1/2" sockets
PARTS FOR TOWER (INCLUDED)
ITEM
Vertical Tower frame tubes with
eyebolts installed
Horizontal Tower tube with eyebolts
and corner connectors
Push-Through Bar for Slider assembly
Yellow trap springs
Blue trap springs
Roll down bar
Yellow long springs
Purple long springs
Single cotton loops (pair)
Safety strap for tower with carabiner
Push Through Bar Slider assembly
Push Through Bar Slider shoulder bolt
21mm x 1/2 inch wrench
PARTS FOR THE TOWER BRACKET KIT
(INCLUDED)
Tower Bracket
L shaped corner brackets
5/32" Allen wench
3/16" Allen wrench
21/64" drill bit
1/4" drill bit
PART NO
QTY
Riser Receivers*
TRP0105
2
Risers with pulleys installed*
Riser retention pins*
TRP0100
1
Black plastic lanyards for riser pins*
707-287
1
1/4"-20 x 2-1/4" Button Head Screws
SPR9002
2
1/4"-20 x 3" Eyebolts
SPR9004
2
1/4" Flat washers
710-010
1
1/4"-20 Nylock nuts
SPR9006
2
5/16"-18 x 1-3/4" Carriage bolts
SPR9461
2
Large (5/16"-18) Nylock nuts
101-005
1
No. 10 finish washers
210-058
1
*Not included if ordered for Reformer with casters.
N/A
2
619-202
2
ALL0060
1
ITEM
PART NUMBER
722-001
622-001
GEN9282
GEN9280
TOL1059
GEN5555
REF0048 (left)
REF0049 (right)
950-184
GEN9402
GEN9037
GEN7314
GEN9232
GEN9305
GEN9021
GEN9013
210-050
1-800-PILATES | +1-916-388-2838
pilates.com | info@pilates.com
QTY
1
4
1
1
1
1
2
2
2
2
6
4
18
12
210-512
4
4
4
Contact Us
400-349 | 01.30.19
Advertisement
Related Manuals for Balanced Body Tower Bracket Retrofit Kit
Summary of Contents for Balanced Body Tower Bracket Retrofit Kit
- Page 1 If you are uncomfortable undertaking any part of this procedure, it is highly recommended that someone with a serviceable knowledge of equipment assembly and tools install the bracket. Balanced Body is not responsible for any damage caused by incorrect assembly.
- Page 2 ASSEMBLY TIME 9. Align the riser on the inside of the frame so that the two Approximately 90 minutes. flanges are on the top and the single flange is on the PREPARE YOUR WORKSPACE bottom. The flanges closer Figure E: Match outside flanges with to the outside of the frame protruding bolt ends.
- Page 3 frame until the be drill bit hits the inside face of the mounting Knobs bracket on the outside face. outward 19. Repeat the process on the other receiver. 20. Insert the metal risers into the receivers and secure them at Figure N: Insert Tower tubes into tube the desired height with the riser pin.
- Page 4 If the pins do not stay in the tube APPENDIX II: INSTALLING THE TOWER BRACKET ON A holes, the pull knobs need to be replaced; call Balanced Body for REFORMER WITH CASTERS replacement parts...