Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Leitner OfficeAlly LH380
Summary of Contents for Leitner OfficeAlly LH380
- Page 1 O f f i c e A l l y ™ L H 3 8 0...
- Page 2 W H E N T HE CALL COU NTS...
-
Page 3: Table Of Contents
CONTENTS Understanding your... Headset controls Charging base Indicator lights Audio signals How to... Set up your headset Connect to Bluetooth Make a landline call Make a Bluetooth call Answer a call Use UniBase Technology ® Control your volume Activate auto-on feature Turn on call control Connect a 2nd headset for conference calls or training Register a new primary headset... -
Page 4: Understanding Your
UNDERSTANDING YOUR HEADSET CONTROLS Incoming Volume Up Microphone Mute Button Incoming Volume Down Headset ON/OFF (and Online Indicator) WHAT’S IN THE BOX Replacement Ear Tips Headset Foam Windscreen Charging Base 8.5v AC Adaptor Lithium-Ion Battery RJ-9 Phone Cord Battery Door Type A-to-Mini USB Cord... -
Page 5: Charging Base
UNDERSTANDING YOUR CHARGING BASE Battery Indicator Computer Mode Button Bluetooth Mode Button Telephone Mode Button Indicator Lights (see page 6) USB Connector Port Power Port AUX Port Telephone Connector Port Handset Connector Port Microphone Volume Up/Down Accessory Selection Switch Compatibility Switch... -
Page 6: Indicator Lights
UNDERSTANDING THE INDICATOR LIGHTS Battery Lights Indicator Lights 100% When the headset battery is Power Light (it’s plugged in) below 20%, the first battery Bluetooth Indicator* (it's connected) light will flash. Online Indicator (headset is on) Charging Light (off when at 100%) This light will turn off when your headset is in the charging base. -
Page 7: Audio Signals
UNDERSTANDING THE AUDIO SIGNALS SOUND WHAT IT MEANS 2 quick beeps (60 sec repeat) Low battery 2 beeps Nearly out of range 2 pitch tone Out of range 2 rapid beeps Back in range 1 beep Receiver volume up/down 2 pitch tone (8 sec repeat) Mute is on 1 beep Mute off/on... -
Page 8: How To
HOW TO SET UP YOUR HEADSET Plug the power adaptor into the charging base. The power light on the base will light up. We recommend charging your headset for at least 4 hours before use. Power port Power light CONNECTING TO A TELEPHONE WITH A HEADSET JACK Use the included connector cord to connect the telephone port on the base to the headset port on your desk phone. - Page 9 See 2a on using the compatibility switch. Handset port Telephone port CONNECTING TO A LEITNER HANDSET LIFTER Connect your (OPTIONAL) headset to your desk phone as shown in Step 2b. Attach the handset lifter to your desk phone and connect it to the AUX port on the charging base.
- Page 10 CONNECTING TO A LEITNER ELECTRONIC HOOKSWITCH (EHS) CABLE Each office phone is a bit different so please refer to the EHS cable (OPTIONAL) instructions for quick and easy setup. With a handset lifter or EHS cable connected, you’ll be able to answer and end calls using the ON/OFF button on the headset—up to 350 feet away from your desk!
-
Page 11: Connect To Bluetooth
HOW TO CONNECT TO BLUETOOTH With your headset turned off, hold down the Bluetooth button ( ) for three seconds until the light starts flashing. Make sure Bluetooth is enabled on the device you're trying to connect to. On most devices like iPhone or Android, this can be found in your settings menu. -
Page 12: Make A Landline Call
HOW TO MAKE A LANDLINE CALL Make sure telephone mode is on ( Press the ON/OFF button ( Press the headset button on your telephone or you can lift the phone handset if yours doesn't have one. If you have a handset lifter or electronic hookswitch (EHS) cable connected to the charging base, the line will automatically connect. -
Page 13: Make A Bluetooth Call
HOW TO MAKE A BLUETOOTH CALL Ensure your Bluetooth device is successfully connected to your charging base by following the steps on page 11. Make sure Bluetooth mode is on ( Press the ON/OFF button ( Dial your call on your Bluetooth device as you normally would. -
Page 14: Answer A Call
HOW TO ANSWER A CALL For incoming landline call: Press the ON/OFF button ( ) and make sure your base is in telephone mode ( Press the headset button on your phone. If your phone doesn't have a headset button, simply lift the handset to activate the call. -
Page 15: Use Unibase ® Technology
HOW TO USE UNIBASE ® UniBase Technology allows you to conference calls between any two devices. Have a call on your cell phone and one on your landline? Conference them together with UniBase! Begin a call on your first device. Hold the mode button for the second device you want to add: Computer ( Bluetooth (... -
Page 16: Control Your Volume
HOW TO CONTROL YOUR VOLUME To adjust the headset listening volume: While the headset is on, use the Incoming Volume Up button ( ) to increase or Incoming Volume Down button ( ) to decrease. The headset will beep each time the volume is adjusted. To mute the headset microphone: Press the mute button ( ). -
Page 17: Activate Auto-On Feature
HOW TO ACTIVATE AUTO-ON Turn this feature on if you’d like your headset to turn on automatically when you pick up your headset off the charging base. To turn this feature on: With your headset turned off, hold the + and – buttons ( ) on your headset together for three seconds. -
Page 18: Connect A 2Nd Headset For Conference Calls Or Training
HOW TO CONNECT A SECONDARY HEADSET FOR Turn on the primary headset. With the secondary headset turned off, place it on the charging base. After a moment, the secondary headset’s online indicator light ( ) will turn on and the primary base’s online indicator light ( ) will flash to show that the headset is registering... - Page 19 TRAINING OR CONFERENCE CALLS If the secondary headset has Auto-On enabled, it will automatically connect when you lift it from the base. If it has Auto-On disabled, press the ON/OFF button ( on the headset to connect. NOTE: The secondary headset will remain registered to the base until the primary headset is turned off or if either headset is returned to its original base.
-
Page 20: Register A New Primary Headset
HOW TO REGISTER A NEW PRIMARY HEADSET In the event that you need to replace your headset, you’ll need to register the new headset to your charging base Press and hold the telephone button ( for five seconds. The light will flash showing the base is in registration mode. -
Page 21: Troubleshooting & Frequently Asked Questions
Start by unplugging the power to the headset base, then remove the battery from the headset for 30 seconds. Reinstall the battery making sure the Leitner logo is facing you. Plug the power back into your base. Press and hold the Telephone Mode button on the base until it flashes, then press and hold the Mute button on the headset until it flashes. -
Page 22: Health And Safety Instructions
It might seem a bit silly, but we’re required to tell you these safety instructions about your Leitner headset. Please keep these instructions for your reference. When using this product, these basic safety precautions and warnings should be followed to reduce the risk of fire, electrical shock, injury to persons, and damage to property. - Page 23 Charging Warnings • Use only the charger provided with your headset to charge the product. Do not use the charger for any other purpose. Ensure that the voltage rating corresponds to the power supply you intend to use. • Charge the headset according to the instructions supplied with the unit. •...
- Page 24 For live product suppor t 1-800-432-3738 Mon-Fri 6:0 0am-4:30pm Pacific Time w w w.leitnerheadset s.com...
Need help?
Do you have a question about the OfficeAlly LH380 and is the answer not in the manual?
Questions and answers