Download Print this page

Takegawa 09-03-0708 Instruction Manual

Multi reflector head light kit for ape type c, 128 mm

Advertisement

Quick Links

Multi Reflector Head Light Kit for Ape Type C, 128 mm
・Thank you for purchasing one of our TAKEGAWA's products. Please strictly follow the following instructions in installing and using the products.
・Before fitting the products, please be sure to check the contents of the Kit. Should you have any questions about the products, please kindly contact
 your local dealer.
・After the installation of this Kit, other parts are additionally required for the installation of turn signals, a horn, a main switch and a speedometer.
Please read the following instructions before installation
◎ We do not take any responsibility for any accident or damage whatsoever arising from the use of this product not in conformity with the instructions
 in this manual.
◎ We shall be held free from any responsibility or compensation whatsoever for any glitch in the parts other than ours if the glitch takes place after the
 installation and use of this product.
◎ If you make alterations to the Kit, we shall be held free from any guarantee of this product.
◎ You are kindly requested not to contact us about the combination of our products with other manufacturers'.
◎ If water gets into the wiring connector or socket, there is a possibility of a short circuit. When driving in the rain or washing your motorcycle, please
 take care not to let the water in the wiring.
◎ Please change the bulb only when it is cool; otherwise, you will get burned from the heated bulb.
◎ Please note that the descriptions in this manual like illustrations and photos may vary from the actual hardware.
The following show the envisioned possibility of injuries to human bodies or property damages as a result of disregarding the
CAUTION
following cautions.
 ・Always try to drive your motorcycle at legal speeds, abiding by the laws.
  (Riding a motorcycle at a speed exceeding the legal speed limit is subject to punishment for overspeeding in violation of the Road Traffic Law.)
 ・ Work only when the engine and muffler are cool. (Otherwise, you will get burned.)
 ・Prepare right tools for the work. (Otherwise, the installation with improper tools could cause breakage of parts or injuries to you.)
 ・Always use a torque wrench to screw bolts and nuts tight and securely to the specified torque.
  (Improper torque could cause these parts to get damaged or fall off.)
 ・As some products and frames have sharp edges or protruding portions, please work with your hands protected.
  (Otherwise, you will suffer injuries.)
 ・Before riding, always check every hardware for slack in parts like screws. If you find slack ones, screw them securely up to the specified
  torque. (Or, improper torque may cause parts to come off.)
 ・The specified specification of the bulb for this head light is PH7 12V 30/30W. When changing the bulbs, be sure to use the bulb of this
  specification. (Any other kind of bulb will cause the breakage of the head light.)
The following show the envisioned possibility of human death or serious injuries to human bodies as a result of disregarding the
WARNING
following warnings.
 ・When you notice something unusual with your motorcycle while riding, immediately stop riding and park your motorcycle in a safe place.
  (Otherwise, the abnormality could lead to accidents.)
 ・Before starting the work, secure your motorcycle firmly on level ground for safety's sake.
  (Otherwise, your motorcycle could overturn and injure you while you are working.)
 ・If you find damaged parts when checking or performing maintenance of your motorcycle, do not use these parts any longer, and replace them
  with new ones. The continued use of these damaged parts as they are could lead to accidents.)
 ・If the bulb of the head light burns out when riding at night, stop riding.
◎ Please be informed that, mainly because of improvement in performance, design changes, and cost increase, the product specifications and   
 prices are subject to change without prior notice.
◎ This manual should be retained for future reference.
Instruction Manual
‑ 1 ‑
Item No.:09−03−0780
Fitting models and frame Nos:
Ape50 : AC16-1000001〜
Ape100 : HC07-1000001〜
Jun./24/ 08

Advertisement

loading

Summary of Contents for Takegawa 09-03-0708

  • Page 1 Ape100 : HC07-1000001〜 ・Thank you for purchasing one of our TAKEGAWA’s products. Please strictly follow the following instructions in installing and using the products. ・Before fitting the products, please be sure to check the contents of the Kit. Should you have any questions about the products, please kindly contact  your local dealer.
  • Page 2 〜 Kit includes 〜 6 1 3 4 7 8 5 2 Part name Repair part No. In packs of 33100-GBJ-T00 Head light unit assembly 090-00-0032 Case screw, 5 mm 09-03-0104 Halogen bulb, TB7 12V30/30W 61310-KRL-T00 Head light stay 61316-GEY-T00 Turn signal stay BW-00-0108 Button head screw, 8 x 20...
  • Page 3 12.Loosely tighten the bolt for holding the head    light, and tighten the turn-signal stay to the      specified torque.    Torque: 12 N・m (1.2 kgf・m) Bolt Co.,Ltd. 3-5-16 Nishikiorihigashi Tondabayashi Osaka Japan TEL : 81-721-25-1357 FAX : 81-721-24-5059 URL : http://www.takegawa.co.jp Jun./24/ 08 ‑ 3 ‑...