Carefree DIRECT RESPONSE Installation Manual

Auto-retract system

Advertisement

Read this manual before installing or using this product. Failure to follow the instructions
and safety precautions in this manual can result in personal injury and/or cause the
product to not operate properly.
The Travel'r Direct Response Auto-Retract System may be installed as part of the original Travel'r awning
installation or as an upgrade to an existing awning installation.
T
C
ABLE OF
ONTENTS
Prior to Installing the Kit ................................................................................................................................ 3 
Installing the Sensor ..................................................................................................................... 4
Switch Installation ......................................................................................................................... 7
Wiring an Additional Extend/Retract Switch ................................................................................................. 8 
Attach the Label ............................................................................................................................ 8
Carefree of Colorado
052567-001r5
T
RAVEL
th
2145 W. 6
Avenue Broomfield, CO 80020
Printed in USA
D
'
IRECT
R
A
UTO
C
AREFREE
R
ESPONSE
-R
S
ETRACT
YSTEM
a Scott Fetzer company
September, 2016
 
 
 

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DIRECT RESPONSE and is the answer not in the manual?

Questions and answers

Dave Londo
June 13, 2025

How do you install a tractioner

Subscribe to Our Youtube Channel

Summary of Contents for Carefree DIRECT RESPONSE

  • Page 1: Table Of Contents

    The Travel'r Direct Response Auto-Retract System may be installed as part of the original Travel'r awning installation or as an upgrade to an existing awning installation.
  • Page 2 OLORADO ROPRIETARY TATEMENT The Travel'r Direct Response is a product of Carefree of Colorado, located in Broomfield, Colorado, USA. The information contained in or disclosed in this document is considered proprietary to Carefree of Colorado. Every effort has been made to ensure that the information presented in the document is accurate and complete.
  • Page 3: Prior To Installing The Kit

    O AVOID SHOCK HAZARD AND OR ACCIDENTAL SYSTEM SHORTING ALWAYS DISCONNECT THE VEHICLE BATTERY AND ELECTRICAL SOURCES BEFORE WORKING WITH ELECTRICAL WIRING AND COMPONENTS When the Direct Response installation is complete return to the original awning instructions for any final assembly required. 052567-001r5...
  • Page 4: Installing The Sensor

    RAVEL IRECT ESPONSE NSTALLATION ANUAL AREFREE OF OLORADO NSTALLING THE ENSOR This section is for fitting the motion sensor and wiring into the motor arm and head. 1. Open the awning completely. 2. Disconnect power to the awning. 3. (Detail A) Remove the front cover. There are six (6) small screws through the back cover.
  • Page 5 AREFREE OF OLORADO NSTALLATION ANUAL RAVEL IRECT ESPONSE Route module wires down and behind motor, Double Sided Clean this surface connect to Tape motor patch cable M o to r A s s y R e a r C o v e r F r o n t Motor Patch C o v e r...
  • Page 6 RAVEL IRECT ESPONSE NSTALLATION ANUAL AREFREE OF OLORADO 8. (Detail B) Clean the inner face of the motor frame. 9. Remove the release paper from the double-sided tape on the module. Position the module with the label out and the two wires at the top and the 5 wires at the bottom. Firmly press the module against the inside face of the motor frame.
  • Page 7: Switch Installation

    Installed in a dedicated switch cabinet with a latching door; or, b) Installed with the optional covered bezel available from Carefree; or, c) Installed in a cabinet with a latching door where the switch is protected and CANNOT activated by any items or cargo that may move or shift during transit;...
  • Page 8: Wiring An Additional Extend/Retract Switch

    LCDR003b TTACH THE ABEL After completing and testing the system, attach the Direct Response identification label to the bottom of the motor arm. Place DR Label 1. Thoroughly clean and dry the area at the bottom of the RH (motor) arm.

Table of Contents