Product Instalation; External Packing And Visual Inspection; Inspection On Item Contained In Packing Box; Inspection On Installation Environment - Viessmann Vitopure S2-2T Manual Book

PRODUCT INSTALLATION
NOTE :
External packaging and visual inspection
Check whether the packing box is damaged, detached or
loose during transportation or loading.
Inspection on items contained in packing
box
Check whether the device is damaged in the packing box.
Check whether there is any missing of the items contained in
packing box.
1 Central water Purifier or
1 Central water softener
2 Valve Unions
1 Drain Pipe
1 Drain pipe hoop
1 power adapter
1 hexagon wrench
EN
NOTE :

Inspection on installation environment

The device is suitable for municipal tap water & Ground
well.
Do not connect unsafe or unknown water source to the
device for filtering.
The device is used to pre-filter tap water and the treated
water is not available for direct drinking.
The working water temperature is 1-39ºC. The device can
not be installed on hot water pipeline.
The device is installed at the rear end of the main water
meter. If other wading device is installed at the rear end of
the water meter, please ensure to install the device in the
front of all wading devices.
Maintenance valves should be installed between the
device and main water meter and between the device and
rear wading device.
Sufficient space is required for installation and operation
during installation.
The ground is flat and can bear the load 150kg. Water inlet
and outlet interfaces, drain channels and 220V power
supply shall be provided around the installation position.
The installation should be away from acid and alkaline
substances or gases to avoid corrosion.
If it is required to install the device outdoors, the device
room should be built to avoid the device exposure to sun,
rain, snow and other damages.
The device and connecting fittings should be insulated in
cold areas to prevent the device and connecting fittings
from being broken.
NOTE :
Installation requirements
Please consciously abide by national and local
regulations on plumbing, electrical appliances and
sanitation during installation.
It is recommended to use the pipe fittings that meet
the requirements specified in national standard
Specifications for Evaluation on Sanitation and Safety
of Drinking Water Distribution Equipment and
Protective Materials.
1 Installation and Service Manual
1 Quality Certificate
1 Warranty Card
NOTE :

Installation steps

Install the water purifier in a correct manner by following the
steps specified in the Installation and Service Manual.
1. Turn off the main water switch
2. Installation requirements for water pipes and
fittings
Arrange water pipe and fittings as close to the wall as
possible.
After pipe laying, fix water pipe and fittings on the wall with
pipe clamps.
When water pipe and fittings are connected, pay attention to
measuring the height and angle.
No obvious stress is allowed after connections, so as to avoid
pipeline damage and leakage due to stress during long-term
use.
3. Connect water pipe to water inlet union
of bypass valve
Measure the distance between the water inlet of water pipe
to water inlet union bypass valve, then cut off the water pipe
in the measured length.
Select the appropriate connection pipe (with internal teeth or
elbow) to connect with water pipe by actual condition.
Connect the water pipe connected with fittings to the water
inlet of water pipe and the water inlet union of bypass valve.
4. Connect water pipe to water outlet union of
bypass valve
Measure the distance between the water outlet of water pipe
to water outlet union bypass valve, then cut off the water pipe
in the measured length.
Select the appropriate connection pipe (with internal teeth or
elbow) to connect with water pipe by actual condition.
Connect the water pipe connected with fittings to the water
outlet of water pipe and the water outlet union of bypass
valve.
5. Connect to drain pipe
Open the upper cover and check controller and bypass valve,
pay attention to the water inlet and outlet direction arrows
marked on control valve body.
Insert one end of drain pipe into the drain outlet on valve body.
Connect and firmly tighten drain pipe to drain outlet with pipe
clamps.
The drain pipe must be fastened, because water will flow out of
the drain at a high flow rate during rinse. Insert drain pipe into
vertical drain pipe, but do not insert it to the end. Seal drain
pipe with sealant around it.
Try to shorten the connection length of drain pipe as much as
possible, reduce curvature and make sure the distance to drain
must not exceed 6m and vertical distance is not higher than
1m.
Do not install various valves in drain pipe. Drain pipe is kept at
a certain distance from the water surface of drain.
When union is mounted, firstly pull out the fixing clamp on
bypass valve.
Push unions into bypass valve.
Insert fixing clamp into the fixing union of bypass valve.
18