Table of Contents
Advertisement
Quick Links
DESMONTADOR DE NEUMÁTICOS
Italiano
English
Français
Deutsch
Español
SMONTAGOMME
TYRE CHANGER
REIFENMONTIERMASCHINE
DEMONTE PNEUS
M 824
Cod. 4-120285A delL'11/2017
Manuale d'uso
Operator's manual
Utilisation et entretien
Betriebs und Wartungsanleitung
Uso y mantenimiento
www.hpa-faip.it
info@hpa-faip.it
Advertisement
Table of Contents
Related Manuals for HPA-Faip M 824
Summary of Contents for HPA-Faip M 824
- Page 1 SMONTAGOMME TYRE CHANGER DESMONTADOR DE NEUMÁTICOS REIFENMONTIERMASCHINE DEMONTE PNEUS M 824 Cod. 4-120285A delL’11/2017 Italiano Manuale d’uso English Operator’s manual Français Utilisation et entretien Deutsch Betriebs und Wartungsanleitung Español Uso y mantenimiento www.hpa-faip.it info@hpa-faip.it...
-
Page 2: Table Of Contents
Inflating tubeless tyres (FS versions only) ............57 TROUBLESHOOTING ..................60 MAINTENANCE ....................62 INFORMATION REGARDING MACHINE DEMOLITION ........62 ENVIRONMENTAL INFORMATION ..............62 OIL - WARNINGS AND RECOMMENDATIONS ..........63 FIREFIGHTING MEANS USABLE ...............63 GLOSSARY ......................64 GENERAL ELECTRIC LAYOUT DIAGRAMS .............64 PNEUMATIC SYSTEM DIAGRAM ..............64 Operator's manual M 824... -
Page 3: Introduction
- depth 1150 mm nameplate applied to the machine itself. - height 970 mm - Packaging weight: - STD version in cardboard 268 Kg in wood Kg 278 - FS version in cardboard 282 Kg in wood 292 Kg Operator's manual M 824... -
Page 4: Ambient Conditions For Machine Transport And Storage
3 box with pressure gauge 4 air tank (FS version only) 5 body - After removing the tower 1, it is advisable to place it in a horizontal position to pre- vent it from falling and getting damaged. Operator's manual M 824... - Page 5 F1 of the column tilting cylinder and lock with nuts and washers R, and tighten the it with ring M. clamp O onto the hose Q (FS version - Connect pipe G to the intermediate union only). Operator's manual M 824...
-
Page 6: Hoisting/Handling
- Temperature range from 0°C to 50°C. WARNING The regulations in force concerning WARNING safety at work must be complied The machine must not be operated in with when choosing the installation potentially explosive atmosphere. position. Operator's manual M 824... -
Page 7: Electrical And Pneumatic Hook-Ups
- ensure that the workshop electrical system includes a functional grounding circuit. - prevent unauthorised use of the ma- chine, always disconnect the power supply plug when the machine is not used (switched off) for extended peri- ods of time. Operator's manual M 824... -
Page 8: Safety Regulations
- When using and servicing the machine, warning contained in this manual. observe the standardised industrial ac- cident prevention regulations for high Operator's manual M 824... -
Page 9: Tyre Changer Description
- Operating pressure....8 - 10 bar DESCRIPTION - Weight..283 Kg (FS version 297 Kg) - Noise levels in operating conditions ..The M 824 is an electro-pneumatic tyre ..........≥ 70 dB (A) changer. The machine is compatible with any type... -
Page 10: Overall Dimensions
A Bead breaking B Tyre demounting and mounting C Inflation area. 880 - 1110 1120 - 1380 WARNING Column tilting must be performed from 1320 work position C (fig.7), keeping the 1880 hands away from moving machine parts. Operator's manual M 824... -
Page 11: Main Working Elements Of The Machine
Learn the function and location of all 13 Bead breaker shoe (movable shoe to detach the bead from the rim). the controls. Carefully check that all controls on the 14 Deflation button (button to remove the Operator's manual M 824... - Page 12 (FS versions only). 22 Shoe guard. 18 Filter Regulator + Lubricator Unit (regu- lates pressure, filters, removes humidity 23 Doyfe connector (fits onto tyre valve for of and lubricates the compressed air inflation). supply). 24 Bead lever Operator's manual M 824...
-
Page 13: Danger Warning Decals
(i.e. facing toward the mount/demount the head. head). Special instructions Alloy wheels Some alloy wheels on the market have minimal rim wells or are even completely without rim wells (these wheels are not DOT approved). Operator's manual M 824... -
Page 14: Bead Breaking
- Adjust the opening of the bead breaking the wheel. shoe by turning the screw located on the cylinder stem (fig.10). Fig.9b A Valve hole B Slight curvature C Pronounced curvature Operator's manual M 824... -
Page 15: Clamping The Wheel
(fig.12). Operator's manual M 824... - Page 16 10”-20” 13”-23” 14”-24” min 17” Operator's manual M 824...
-
Page 17: Demounting
(fig 15a), and position the mounting/ demounting device correctly against the rim edge (fig.16). IMPORTANT: pressing the button locks both the vertical and horizontal arms simultaneously. This space between the rim and the verti- Operator's manual M 824... -
Page 18: Mounting
ATTENTION: If the tyre has an inner tube, move the arm out of the working position then remove the inner tube. Operator's manual M 824... -
Page 19: Approved Uhp And Run Flat Tyre Demounting And Mounting Proce- Dure
Failure to - Move the column forward in “not working comply with the instructions below will position”, then remove the wheel from render tyre inflation dangerous. the tyre changer. Operator's manual M 824... -
Page 20: Inflating Procedure
- Make sure that the wheel is secured to the table top with inside clamping (Fig. 27). Operator's manual M 824... -
Page 21: Troubleshooting
➥ Replace the silencer. Cylinder seals worn. ➥ Replace the gaskets. ➥ Replace the bead breaker cylinder. Note: to improve the operation of the tubeless tyre inflation system the compressed air line pressure must be between 8/10 bar. Operator's manual M 824... - Page 22 ➥ Replace the cock or column tilting cylinder. Air leaks from the vertical and horizontal arm locking cock Valve seal damaged. ➥ Replace the handle cock. Clamping arm cylinders leak air Faulty piston or seals. ➥ Replace the pistons and gaskets. Operator's manual M 824...
-
Page 23: Maintenance
Periodically check the lubricant level through the specific windows and top up as shown in fig.31c. Top up only with WARNING non-detergent SAE20 oil equal to 50cc. Before adjusting or servicing the ma- The filter regulator "FR" has an automatic Operator's manual M 824... - Page 24 If a manual operation is not from the machine. When cleaning the area, take steps to avoid building up sufficient, use the specific key provided (fig.31e). and raising dust as far as possible. Operator's manual M 824...
-
Page 25: Information Regarding Machine Demolition
In this way it is possible to prevent that a non specific treatment of the substances contained in these products, or their im- proper use, or improper use of their parts may be hazardous to the environment or Operator's manual M 824... -
Page 26: Oil - Warnings And Recommendations
The applica- tions of each type of extinguisher will Mineral oil: First aid instructions be illustrated fully by the respective - Swallowing: go to Casualty with the manufacturers on request. characteristics of the type of oil swallowed. Operator's manual M 824... -
Page 27: Glossary
Column translation cylinder Fig. 33 Swivel connector Power supply socket Delivery valve Single / two-speed motor Tank Relief valve Motor 5/2 NO Valve Two-speed micro-switch Tool actuator cylinder Micro-switch Inflation limiter unit CLOCKWISE rotation) Micro-switch ANTICLOCKWISE rotation) Operator's manual M 824... - Page 28 Operator's manual M 824...
- Page 29 Operator's manual M 824...
- Page 30 Operator's manual M 824...
- Page 31 Operator's manual M 824...
- Page 32 STANDARD VERSION Operator's manual M 824...
- Page 33 FS VERSION Operator's manual M 824...
- Page 34 STANDARD VERSION AIR MOTOR Operator's manual M 824...
- Page 35 FS VERSION AIR MOTOR Operator's manual M 824...
- Page 36 Notes Operator's manual M 824...
- Page 37 Notes Operator's manual M 824...
Need help?
Do you have a question about the M 824 and is the answer not in the manual?
Questions and answers