Table of Contents
Advertisement
Quick Links
1
APPLICATION .................................................................................. 4
2
DESCRIPTION ................................................................................. 4
3
PACKAGE CONTENT LIST ............................................................. 5
4
SYMBOLS ........................................................................................ 5
5
GENERAL POWER TOOL SAFETY WARNINGS .......................... 6
5.1
Work area ................................................................................................................ 6
5.2
Electrical safety ....................................................................................................... 6
5.3
Personal safety ....................................................................................................... 6
5.4
Power tool use and care ......................................................................................... 7
5.5
Service ..................................................................................................................... 7
6
6.1
For both Mitre saw mode and table saw (bench saw) mode: ............................... 7
6.2
When using in Mitre saw mode: ............................................................................. 8
6.3
When using in the table saw (bench saw) mode: .................................................. 8
7
INSTALLATION ................................................................................ 9
7.1
Bench mounting (Fig. 1 & 3) ................................................................................... 9
7.1.1
For the fully-extended feet set up as the high table. .................................................. 9
7.1.2
For the folded feet set up as the low table ................................................................. 9
8
FUNCTIONAL DESCRIPTION ......................................................... 9
8.1
Blade guard (Fig. 4, 5 & 6) ...................................................................................... 9
8.2
Maintaining maximum cutting capacity (Fig. 7) .................................................. 10
8.3
Adjusting the Mitre angle (Fig. 9 & 10) ................................................................. 11
8.4
Adjusting the bevel angle (Fig. 11 & 12) .............................................................. 11
8.4.1
In the Mitre saw mode ............................................................................................. 11
8.4.2
In the table saw mode (Fig. 13) ............................................................................... 11
8.5
Switch action (Fig. 14) .......................................................................................... 11
8.5.1
Switch for the table saw mode (B) ........................................................................... 11
8.6
Adjusting the depth of cut (Fig. 15 - 21) .............................................................. 11
9
ASSEMBLY .................................................................................... 11
9.1
Socket wrench storage (Fig. 17)........................................................................... 11
9.2
Table height two-way set up ................................................................................. 12
Copyright © 2014 VARO NV
POWX0760
P a g e
| 1
EN
www.varo.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for VARO Powerplus POWX0760
Summary of Contents for VARO Powerplus POWX0760
-
Page 1: Table Of Contents
Switch for the table saw mode (B) ................11 Adjusting the depth of cut (Fig. 15 - 21) .............. 11 ASSEMBLY ..................11 Socket wrench storage (Fig. 17)................11 Table height two-way set up ................. 12 Copyright © 2014 VARO NV www.varo.com P a g e... - Page 2 Mitre cutting ....................... 17 10.1.3 Bevel cut ......................17 10.1.4 Compound cutting ....................18 10.1.5 Cutting aluminum extrusion (Fig. 56) ..............18 10.2 Cutting as table saw (bench mode) ..............18 Copyright © 2014 VARO NV www.varo.com P a g e...
- Page 3 11.3 After use ........................ 21 11.4 Service ........................21 TECHNICAL DATA ................ 21 NOISE ..................... 22 STORAGE ..................22 WARRANTY ................... 22 ENVIRONMENT ................23 DECLARATION OF CONFORMITY ..........23 Copyright © 2014 VARO NV www.varo.com P a g e...
-
Page 4: Application
25. Switch lever 62. Fastener 94. Limit mark 26. On button 63. / 95. Brush holder cap 27. Off button 64. Vise arm 96. Screwdriver 28. Stopper pin 65. Vise rod Copyright © 2014 VARO NV www.varo.com P a g e... -
Page 5: Package Content List
Do not place hand or fingers Wear gloves close to the blade. In accordance with essential requirements of the European Wear noise protection directive(s) Copyright © 2014 VARO NV www.varo.com P a g e... -
Page 6: General Power Tool Safety Warnings
Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. Copyright © 2014 VARO NV www.varo.com P a g e... -
Page 7: Power Tool Use And Care
Always use accessories recommended in this manual. Use of improper accessories such as abrasive cut-off wheels may cause an injury. Copyright © 2014 VARO NV www.varo.com P a g e... -
Page 8: When Using In Mitre Saw Mode
When using in the table saw (bench saw) mode: Do not perform any operation freehand. Freehand means using your hands to support or guide the workpiece, in lieu of (6) rip fence. Copyright © 2014 VARO NV www.varo.com P a g e... -
Page 9: Installation
When lowering the handle while pushing the lever to the left, the lower blade guard A rises automatically. The lower blade guard B rises as it contacts a workpiece. The lower blade Copyright © 2014 VARO NV www.varo.com P a g e... -
Page 10: Maintaining Maximum Cutting Capacity (Fig. 7)
To use the tool with the lower limit, move the stopper end clockwise. Use in this position is proper to cut a thick workpiece. Copyright © 2014 VARO NV www.varo.com P a g e... -
Page 11: Adjusting The Mitre Angle (Fig. 9 & 10)
The socket wrench is stored as shown in the figure. When using the socket wrench, pull it out of the wrench holder. After using the socket wrench, return it to the wrench holder. Copyright © 2014 VARO NV www.varo.com P a g e... -
Page 12: High Table Set Up (Fig. 18)
Always check to see that the riving knife is secured and that the top blade guard works smoothly before cutting. Copyright © 2014 VARO NV www.varo.com P a g e... -
Page 13: Installing And Adjusting Rip Fence (Fig. 28)
(2) Shift the front edge of the rip fence slightly to right or left until it becomes parallel with the blade. (3) Tighten the adjusting screw on the rip fence firmly. CAUTION: Copyright © 2014 VARO NV www.varo.com P a g e | 13... -
Page 14: Installing And Adjusting Mitre Gauge (Fig. 35)
Before use in the table saw mode, make sure that the riving knife has been secured in place properly. Before use in the table saw mode, remove the lower blade guard (8) In table saw mode, release the lower limit stopper. Copyright © 2014 VARO NV www.varo.com P a g e | 14... -
Page 15: Securing The Turn Table (Fig. 41)
After releasing the push button, make sure that the top blade guard is secured by trying to pull it out. Copyright © 2014 VARO NV www.varo.com P a g e... -
Page 16: Setting Up The Tool In Mitre Saw Mode (Fig. 50)
Refer to the table below for the relation between the size of workpiece and use/unuse of sub fences R and L. (Fig. 53) Workpiece size (H x W) Use/Unuse of subfence 65mm x 155mm With sub fences 20mm x 200mm Without sub fences Copyright © 2014 VARO NV www.varo.com P a g e | 16... -
Page 17: Operation
When pressing the handle down, apply pressure parallel to the blade. If the pressure is not parallel to the blade during a cut, the angle of the blade might be shifted and the precision of the cut will be impaired. Copyright © 2014 VARO NV www.varo.com P a g e... -
Page 18: Compound Cutting
(Never use nails in push block.) 10.2.3 Auxiliary fence (Fig. 58) Make auxiliary fence from 9.5 mm and 19 mm plywood pieces. Copyright © 2014 VARO NV www.varo.com P a g e | 18... -
Page 19: Ripping
To prevent a long board from wobbling, fit the Mitre gauge with an auxiliary fence board. Fasten with bolts/ nuts after drilling holes, but fasteners must not protrude from the face board. Copyright © 2014 VARO NV www.varo.com P a g e... -
Page 20: Carrying Tool (Fig. 66)
45°, turn, from the underside of the table, the 45° bevel angle adjusting bolt on the left side of the sub arm until the pointer points to 45°. (Fig. 72) Copyright © 2014 VARO NV www.varo.com P a g e... -
Page 21: Replacing Carbon Brushes (Fig. 73 & 74)
0° - 45° 40 x 155mm 45° - 45° 40 x 105mm Table saw Table size (W x L) 500 x 540mm Max. Cutting capacity 90° 70mm 45° 50mm Copyright © 2014 VARO NV www.varo.com P a g e | 21... -
Page 22: Noise
Your appliance must be returned undismantled to your dealer in an acceptably clean state, (in its original blow-moulded case if applicable to the unit), accompanied by proof of purchase. Copyright © 2014 VARO NV www.varo.com P a g e | 22... -
Page 23: Environment
EN55014-1 : 2006 EN55014-2 : 1997 EN61000-3-2 : 2006 EN61000-3-11 : 2000 Keeper of the Technical Documentation : Philippe Vankerkhove, VARO – Vic. Van Rompuy N.V. The undersigned acts on behalf of the company CEO, Hugo Cuypers Regulatory Affairs – Compliance Manager Date : 21/03/2013 Copyright ©...
Need help?
Do you have a question about the Powerplus POWX0760 and is the answer not in the manual?
Questions and answers