Advertisement
www.arcaudio.com
MOTO 720
MOTO 600.4
4 Channel Motocycle and
Introduction
Introduction
Finding a Suitable Location
Finding a Suitable Location
Supplying Power
Supplying Power
The Ground
The Ground
Running the Cables
Running the Cables
Class D amplifiers
Class D ampli ers
Diagnostic Fault Codes
Diagnostic Fault Codes
Controls and Features
Controls and Features
Inputs
Gains
Crossovers
Bass Boost
Remote Status Dispaly
Ohm Load Matching
Speaker Outputs
Installation Instructions
Installation Instructions
System Diagrams
System Diagrams
2 Speaker System
4 Speaker System
8 Speaker System
2/4 Speakers W/Subwoofer
2/4 Speakers W/Subwoofer
Auto Detect
Auto Detect
Speaker Level Input
Speaker Level Input
Specifications
Speci cations
Dimensions
Dimensions
Warranty
Warranty
®
Off-Road Amplifier
Inputs
Gains
Crossovers
Ohm Load Matching
Speaker Outputs
2 Speaker System
4 Speaker System
8 Speaker System
1
1
1
1
2
2
2
3
3
3
3
4
4
4
5
6
7
8
9
10
10
11
11
11
OWNER'S MANUAL
1
1
1
1
2
2
2
3
3
3
4
4
5
6
7
8
9
10
10
11
11
11
TOP
Advertisement
Table of Contents
Related Manuals for ARC Audio MOTO 720
Summary of Contents for ARC Audio MOTO 720
- Page 1 OWNER’S MANUAL ® www.arcaudio.com MOTO 720 MOTO 600.4 4 Channel Motocycle and Off-Road Amplifier Introduction Introduction Finding a Suitable Location Finding a Suitable Location Supplying Power Supplying Power The Ground The Ground Running the Cables Running the Cables Class D amplifiers...
-
Page 2: Installation Instructions
Your ampli er Does NOT make power. It converts power, or current, from your electrical system and turns it into a high power musical energy. If the amp can't get all the power it needs it will not produce its full output. Your ARC Audio ampli- er will produce Full output for longer then other amps on the market today. -
Page 3: Diagnostic Faul T Codes
Running the Cables Carefully run the power and signal cables through the passenger compartment of the vehicle. Running power down one side and signal down the other is the preferred method. If this isn’t possible, keep them separated as much as possible. When running through any metal, always use a rubber grommet to prevent the power wire from shorting and to reduce the risk of fire. -
Page 4: Input Section
Gain Because of the wide range of head unit output con gurations all ARC Audio ampli ers have an adjustable input sensitivity or “Gain” . The gain is not a volume or a power limiting control like a throttle. It makes the amp more sensitive to input from the stereo. -
Page 5: Speaker Outputs
Ohm Load Matching This ampli er is equipped with a unique impedance matching system that allows you to mix a wide range of Ohm loads and still achieve full power. This can be done independently on the front and rear channels. 2Ω... - Page 6 Installation Instructions Below is a very abbreviated set of installation instructions. This is not meant as a step by step procedure but is intended to give you a general idea of what is involved and which steps come rst. Every installation will be di erent and may require reordering of these steps.
- Page 7 BRIDGED 2 CHANNEL HIGHPASS OR FULL RANGE Set to Set to BRIDGED 2CH BRIDGED 2CH NOT USED NOT USED NOT USED Not Used Not Used Not Used INPUT SELECT CH3-4 4CH STEREO FREQ Hz CH3-4 GAIN INPUT SELECT MAKE SURE THESE FREQ Hz GAIN 4CH STEREO...
- Page 8 4-SPEAKER SYSTEM Use this 2 OR 4 STEREO 2 OHM STEREO crossover Set to Set to for HIGH HIGH Use this Set to 4CH STEREO Set to Crossover HIGH 4CH STEREO for HIGH INPUT CH3-4 SELECT INPUT CH3-4 SELECT 4CH STEREO FREQ Hz GAIN 4CH STEREO...
- Page 9 8-SPEAKER SYSTEM 2 OHM STEREO Use this crossover Set to Set to for HIGH HIGH 4CH STEREO Use this Set to Set to Crossover HIGH 4CH STEREO for HIGH CH3-4 INPUT INPUT SELECT SELECT FREQ Hz GAIN 4CH STEREO CH3-4 4CH STEREO FREQ Hz 2 CHANNEL...
-
Page 10: Bass Boost
STEREO HIGH PASS With MONO SUBWOOFER Use this Use this Set to Set to Crossover HIGH crossover 4CH STEREO Set to Set to for HIGH for HIGH HIGH 4CH STEREO INPUT SELECT CH3-4 4CH STEREO FREQ Hz GAIN CH3-4 INPUT MAKE SURE THESE SELECT FULL... -
Page 11: Auto Detect Speaker Level Input
AUTO DETECT SPEAKER LEVEL INPUT AUTO SENSE uses a BTLD (Bridge Tied Load) Auto Detect Turn-on circuit that offers a significant improvement in reliability over previous designs. Instead of relaying on the music to supply enough signal to turn the amplifier on. Robert Zeff’s design detects the IC (chip) used in the vast majority of stock head units and amplifiers. -
Page 12: Specifications
YEAR from the original date of purchase. This warranty is not transferable and applies only to the original retail purchaser this warranty for any reason due to manufacture defects ARC AUDIO will, at its sole discretion, repair or replace the defective of the product from an authorized ARC AUDIO retailer.