Subscribe to Our Youtube Channel
Related Manuals for ARC Audio X2 600.4
Summary of Contents for ARC Audio X2 600.4
-
Page 1: Table Of Contents
® X2 600.4 FULL-RANGE CLASS D AMPLIFIER OWNER’S MANUAL Table of Contents Topic Page Introduction Finding a Suitable Location Supplying Power The Ground Connection Running Cables Class D Amplifier Recommendations Diagnostic Fault Codes Speaker Level Input Pigtails Input Section... -
Page 2: Introduction
If the amp can’t get the power it needs form your alternator and battery, it will not be able to produce its full output. Your ARC Audio amplifier will produce full output for longer than other amps on the market today. If the Voltage or Current drops too low, even our amplifiers will drop below their rated output. -
Page 3: Class D Amplifier Recommendations
Speaker Level Input Pigtails All ARC Audio X2-Series amplifiers include a set of high-level speaker input RCA pigtails. These pigtails include a resistive voltage divider network to reduce the signal from a high-power source unit or factory amplifier so that it can be used with the differential Inputs on your X2-Series Amp. -
Page 4: Input Section
DC DETECT net frequency response of the total system is smooth with no CH1/2 over- or under-lap. Crossover Range and Function Controls The X2 600.4 features an elaborate crossover system that can CH3/4 HIGHPASS BAND LOWPASS operating in low-pass or high-pass on all pairs of channels, and... -
Page 5: Bass Boost
DC DETECT CH1/2 2 CH INPUT Load Impedance TURN ON A unique feature of the X2 600.4 is it’s adjustable rail voltage +12V system. Each pair of channels includes a LOAD SELECT switch. CH1/2 CH3/4... -
Page 6: Speaker Output Connections
Accessing Controls and Mounting Provisions The X2 600.4 features our Level 2 X2-Series cosmetics. The amplifier shroud features an elegant new silver brushed- aluminum extruded aluminum design. An acrylic plastic badge in the center of the amp illuminates in blue when the amp is on, and can flash diagnostic codes as required. -
Page 7: Auto-Sense Turn On Detection
2 CH INPUT Remote Level Control TURN ON The X2 600.4 ships with a remote level control that can be +12V installed in near the driver’s seat so the owner can adjust the level of a subwoofer. The level control only affects Channels 1 &... -
Page 8: Installation Instructions
In cases where multiple amplifiers share a common power wire, ensure each device has proper protection with a fuse. The fuses built-in to the ARC Audio X2-Series amplifiers satisfy this need. Processors, lighting, etc. will require dedicated fuses for safe operation. -
Page 9: Stereo 4-Channel High-Pass Configuration
X2 600.4 STEREO 4-CHANNEL HIGH-PASS Use this control Set CH 3/4 Set Bridge Mode to adjust CH3/4 Crossover to 4 CH HP Frequency function to Stereo HIGH CH3/4 HIGHPASS BAND LOWPASS INPUT SELECT FREQ Hz PASS FREQ Hz LP RANGE... -
Page 10: Stereo Hp With Mono Subwoofer Configuration
X2 600.4 STEREO HIGH-PASS with MONO SUBWOOFER Use this control Set CH 3/4 Set Bridge Mode to adjust CH3/4 Crossover to 4 CH HP Frequency function to Stereo HIGH CH3/4 HIGHPASS BAND LOWPASS INPUT SELECT FREQ Hz PASS FREQ Hz... -
Page 11: Bridged 2-Channel Configuration
X2 600.4 BRIDGED 2-CHANNEL Set Bridge Mode to Bridged 2CH Stereo CH3/4 HIGHPASS BAND LOWPASS INPUT SELECT FREQ Hz PASS FREQ Hz LP RANGE LOW FULL GAIN 4CH STEREO HIGH BRIDGED 2CH CH 1/2 BASS HIGHPASS AUTO SENSE BOOST FREQ Hz... -
Page 12: Specifications
“Out of Warranty” repair cost. In no event will ARC AUDIO be liable for incidental, consequential, or other damages resulting from the use or miss-use of this product. This includes but is not limited to, damage of hearing, property or person, damage based upon inconvenience or in loss of use of the product, and to the extent permitted by law, damages for personal injury.
Need help?
Do you have a question about the X2 600.4 and is the answer not in the manual?
Questions and answers