Advertisement
www.arcaudio.com
4 Channel Motocycle and
Introduction
Finding a Suitable Location
Supplying Power
The Ground
Running the Cables
Class D amplifiers
Diagnostic Fault Codes
Controls and Features
Inputs
Crossovers
Bass Boost
Remote Status Dispaly
Ohm Load Matching
Speaker Outputs
Installation Instructions
System Diagrams
8 Speaker System
2/4 Speakers W/Subwoofer
®
Off-Road Amplifier
1
1
1
1
2
2
2
3
3
3
3
4
4
4
5
6
7
8
9
10
10
11
11
11
OWNER'S MANUAL
TOP
Advertisement
Table of Contents
Related Manuals for ARC Audio MOTO 600.4
Summary of Contents for ARC Audio MOTO 600.4
-
Page 1: Table Of Contents
OWNER’S MANUAL ® www.arcaudio.com MOTO 600.4 4 Channel Motocycle and Off-Road Amplifier Introduction Finding a Suitable Location Supplying Power The Ground Running the Cables Class D amplifiers Diagnostic Fault Codes Controls and Features Inputs Gains Crossovers Bass Boost Remote Status Dispaly... - Page 2 Your amplifier Does NOT make power. It converts power, or current, from your electrical system and turns it into a high power musical energy. If the amp can't get all the power it needs it will not produce its full output. Your ARC Audio ampli- fier will produce Full output for longer then other amps on the market today.
- Page 3 Running the Cables Carefully run the power and signal cables through the passenger compartment of the vehicle. Running power down one side and signal down the other is the preferred method. If this isn’t possible, keep them separated as much as possible. When running through any metal, always use a rubber grommet to prevent the power wire from shorting and to reduce the risk of fire.
- Page 4 Gain Because of the wide range of head unit output configurations all ARC Audio amplifiers have an adjustable input sensitivity or “Gain” . The gain is not a volume or a power limiting control like a throttle. It makes the amp more sensitive to input from the stereo.
- Page 5 Remote Status Display MOTO 600.4 is equipped with a Remote Status Display LED that can be mounted in a visible location near the amplifier. By simply plugging in the Status LED you will have a visible indicator that matches the function of the Power/Protect light on the amplifier.
- Page 6 Installation Instructions Below is a very abbreviated set of installation instructions. This is not meant as a step by step procedure but is intended to give you a general idea of what is involved and which steps come first. Every installation will be different and may require reordering of these steps.
-
Page 7: Moto 600.4
MOTO 600.4 BRIDGED 2 CHANNEL HIGHPASS OR FULL RANGE Set to BRIDGED 2CH NOT USED NOT USED NOT USED INPUT SELECT CH3-4 4CH STEREO FREQ Hz GAIN MAKE SURE THESE 2 CHANNEL FULL SWITCHES ARE IN THE BRIDGED HIGH BB ALL... -
Page 8: Speaker System
MOTO 600.4 4-SPEAKER SYSTEM 2 OHM STEREO Use this Set to Set to Crossover HIGH 4CH STEREO for HIGH INPUT SELECT CH3-4 4CH STEREO FREQ Hz GAIN 2 CHANNEL FULL MAKE SURE THESE BRIDGED HIGH BB ALL SWITCHES ARE IN THE... -
Page 9: Speaker System
MOTO 600.4 8-SPEAKER SYSTEM 2 OHM STEREO Use this Set to Set to Crossover HIGH 4CH STEREO for HIGH INPUT SELECT CH3-4 4CH STEREO FREQ Hz GAIN MAKE SURE THESE FULL 2 CHANNEL SWITCHES ARE IN THE HIGH BRIDGED BB ALL... - Page 10 MOTO 600.4 STEREO HIGH PASS With MONO SUBWOOFER Use this Set to Set to Crossover HIGH 4CH STEREO for HIGH INPUT SELECT CH3-4 4CH STEREO FREQ Hz GAIN MAKE SURE THESE 2 CHANNEL FULL SWITCHES ARE IN THE HIGH BRIDGED...
-
Page 11: Auto Detect
MOTO 600.4 AUTO DETECT SPEAKER LEVEL INPUT AUTO SENSE MOTO 600.4 uses a BTLD (Bridge Tied Load) Auto Detect Turn-on circuit that offers a significant improvement in reliability over previous designs. Instead of relaying on the music to supply enough signal to turn the amplifier on. Robert Zeff’s design detects the IC (chip) used in the vast majority of stock head units and amplifiers. -
Page 12: Specifications
ARC AUDIO retailer. Upon inspection by ARC AUDIO should services be necessary under this warranty for any reason due to manufacture defects ARC AUDIO will, at its sole discretion, repair or replace the defective product with new or similar conditioned product at no charge.
Need help?
Do you have a question about the MOTO 600.4 and is the answer not in the manual?
Questions and answers