Related Manuals for tams elektronik 70-01035
Summary of Contents for tams elektronik 70-01035
- Page 1 Manual Adapter for PluX22-, 21MTC- and SUSI-Interface Item no. 70-01035 PluX22 NEM 660 NEM 658 | RCN-122 RCN-121 tams elektronik n n n...
-
Page 2: Table Of Contents
10. EU declaration of conformity............19 11. Declarations conforming to the WEEE directive......19 © 10/2017 Tams Elektronik GmbH All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, without prior permission in writing from Tams Elektronik GmbH. -
Page 3: Getting Started
Adapter for PluX22-, 21MTC- and SUSI-Interface English 1. Getting started How to use this manual This manual gives step-by-step instructions for safe and correct assembly of the kit and fitting and connecting of the ready-built module, and operation. Before you start, we advise you to read the whole manual, particularly the chapter on safety instructions and the checklist for trouble shooting. - Page 4 English Adapter for PluX22-, 21MTC- and SUSI-Interface Required materials For assembling the kit you need: an electronic soldering iron (max. 30 Watt) or a regulated soldering iron with a fine tip and a soldering iron stand a tip-cleaning sponge ...
-
Page 5: Safety Instructions
Adapter for PluX22-, 21MTC- and SUSI-Interface English 2. Safety instructions Mechanical hazards Cut wires can have sharp ends and can cause serious injuries. Watch out for sharp edges when you pick up the PCB. Visibly damaged parts can cause unpredictable danger. Do not use damaged parts: recycle and replace them with new ones. - Page 6 English Adapter for PluX22-, 21MTC- and SUSI-Interface Fire risk Touching flammable material with a hot soldering iron can cause fire, which can result in injury or death through burns or suffocation. Connect your soldering iron or soldering station only when actually needed.
-
Page 7: Safe And Correct Soldering
Adapter for PluX22-, 21MTC- and SUSI-Interface English In schools, training centres, clubs and workshops, assembly must be supervised by qualified personnel. In industrial institutions, health and safety regulations applying to electronic work must be adhered to. 3. Safe and correct soldering Caution: Incorrect soldering can cause dangers through fires and heat. - Page 8 English Adapter for PluX22-, 21MTC- and SUSI-Interface Do not move the component for about 5 seconds after soldering. To make a good soldering joint you must use a clean and unoxidised soldering tip. Clean the soldering tip with a damp piece of cloth, a damp sponge or a piece of silicon cloth.
-
Page 9: Operation Overview
Adapter for PluX22-, 21MTC- and SUSI-Interface English 4. Operation overview The adapter is used to upgrade vehicles with a PluX or MTC interface interface. There is a 22-pole socket soldered on to the adapter PCB which is used to insert the plug connector of the decoder-sided PluX interface. -
Page 10: Technical Specifications
English Adapter for PluX22-, 21MTC- and SUSI-Interface 5. Technical specifications Max. current per connecting pin 1.000 mA IP 00 Protected to Ambient temperature in use 0 ... +60 °C Ambient temperature in storage -10 ... +80 °C Comparative humidity allowed max. - Page 11 Adapter for PluX22-, 21MTC- and SUSI-Interface English Mounting versions for MTC decoders Version 1 a: Inserting direction from top socket terminal strip of the decoder on top Version 1 b: Inserting direction from bottom socket terminal strip of the decoder on top Version 2 a: Inserting direction from top socket terminal strip of the...
-
Page 12: Assembling The Kit
English Adapter for PluX22-, 21MTC- and SUSI-Interface 7. Assembling the kit Solder the connecting cables on the top side of the adapter PCB. Observe the different assignments for PluX and MTC interfaces and the different mounting versions. It is recommended to use cables of different colours according to NEM 658 or NEM 660 in order to avoid mistakes when connecting the adapter PCB. - Page 13 Adapter for PluX22-, 21MTC- and SUSI-Interface English Pin Name Description Plux adapter Cable colour GPIO/C universal input/output AUX3 output 3 GPIO/B universal input/output, train-bus pulse GPIO/A universal input/output, train-bus data decoder ground, pick-off after rectifier V+ Cap. decoder plus, pick-off after rectifier, blue connection storage capacitor lighting forward direction...
-
Page 14: Assignment For 21Mtc Adapters (Nem 660/Rcn-121)
English Adapter for PluX22-, 21MTC- and SUSI-Interface 7.2. Assignment for 21MTC adapters (NEM 660/RCN-121) In order to avoid damage due to a connection of the decoder with reversed polarity, you sould remove the index pin (pin 11) at the 22- pole plug connector. -
Page 15: Soldering A Plug For The The Susi Interface
Adapter for PluX22-, 21MTC- and SUSI-Interface English Pin Name Description MTC adapter Cable colour lighting backward direction white LS/A loudspeaker connection A brown LS/B loudspeaker connection B brown Index not in use, coding internal decoder voltage 1,8 – 5,7 volts AUX3 output 3 AUX2... -
Page 16: Performing A Visual Check
English Adapter for PluX22-, 21MTC- and SUSI-Interface 7.4. Performing a visual check After having soldered the cables (and as needed the SUSI plug) you should perform a visual check and remedy defects. Check if soldering joints closely adjoining are connected to each other by accident. - Page 17 Adapter for PluX22-, 21MTC- and SUSI-Interface English Possible cause: The cables on the PCB have not been assigned properly to the decoder / the connections in the vehicle. à Check the connections. Possible cause: The plug connector or the socket have been inserted the wrong way.
-
Page 18: Guarantee Bond
English Adapter for PluX22-, 21MTC- and SUSI-Interface 9. Guarantee bond For this product we issue voluntarily a guarantee of 2 years from the date of purchase by the first customer, but in maximum 3 years after the end of series production. The first customer is the consumer first purchasing the product from us, a dealer or another natural or juristic person reselling or mounting the product on the basis of self- employment. -
Page 19: Eu Declaration Of Conformity
Adapter for PluX22-, 21MTC- and SUSI-Interface English 10. EU declaration of conformity This product conforms with the EC-directives mentioned below and is therefore CE certified. 2004/108/EG on electromagnetic. Underlying standards: EN 55014-1 and EN 61000-6-3. To guarantee the electromagnetic tolerance in operation you must take the following precautions: ... - Page 20 Information and tips: http://www.tams-online.de Warranty and service: Tams Elektronik GmbH Fuhrberger Straße 4 DE-30625 Hannover fon: +49 (0)511 / 55 60 60 fax: +49 (0)511 / 55 61 61 e-mail: modellbahn@tams-online.de...