Table of Contents
Advertisement
1-conduit Models
Adjustable Roller Lever, Form Lock
(with Metal Lever, Resin Roller)
D4N-1@2G
D4N-2@2G
D4N-3@2G
D4N-4@2G
D4N-9@2G *
17.5 dia. × 6.8
resin roller
18
9
± 0.2
2.5
47
± 0.2
55
20
± 0.1
22
± 0.1
22
± 0.2
31 max.
Note: Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions.
* Refer to following diagrams for details on M12 connectors.
Snap-action (1NC/1NO) (2NC), Slow-action (2NC) (3NC)
Operating characteristics
Operating force
OF max.
Release force
RF min.
Pretravel
PT
Overtravel
OT min.
Movement differential
MD max. *2
Operating position
OP
Total travel
TT *3
Direct opening travel
DOT min. *4
Direct opening force
DOF min. *4
Slow-action (1NC/1NO) (2NC/1NO)
Operating characteristics
Operating force
OF max.
Release force
RF min.
Pretravel
PT *2
PT (2nd) *3
PT *4
PT (2nd) *5
Overtravel
OT min.
Operating position
OP
Total travel
TT *6
Direct opening travel
DOT min.
Direct opening force
DOF min. *7
1-conduit M12 Connector
D4N-9@@@
(14)
http://www.ia.omron.com/
45
± 1
39.5
± 1
(31)
11
± 0.2
20 to 66R
20.5 × 20.5
27.5
21.5
2.15±0.05R
mounting holes
14.2
+0.15
Conduit cap
Two, 4
dia. holes
30
0
Depth: 5
Model
D4N-@12H
D4N-@12G
D4N-@22H
D4N-@22G
D4N-@B2H
D4N-@B2G
D4N-@D2H
D4N-@D2G
*1
4.5 N
0.4 N
18 to 27
40
14
---
(80 )
50
20 N
Model
D4N-@A2H
D4N-@A2G
D4N-@C2H
D4N-@C2G
D4N-@E2H
D4N-@E2G
D4N-@F2H
D4N-@F2G
*1
4.5 N
0.4 N
18 to 27
(44 )
27.5 to 36.5
(18 )
40
---
(80 )
50
20 N
M12 × 1
14.2
30
Adjustable Roller Lever, Form Lock
(with Metal Lever, Rubber Roller)
D4N-1@2H
D4N-2@2H
D4N-3@2H
D4N-4@2H
D4N-9@2H *
Bearing
18
9
±0.2
2.5
± 0.2
47
55
± 0.1
20
22
± 0.1
± 0.2
22
31 max.
Note: Variation occurs in the simultaneity of contact
opening/closing operations of 2NC, 2NC/1NO, and
3NC contacts. Check contact operation.
*1. The operating characteristics of these Switches were
measured with the roller lever set at 32 mm.
*2. Only for snap-action models.
*3. Reference value.
*4. For safe use, always make sure that the minimum values
or greater are provided.
*1. The operating characteristics of these Switches were
measured with the roller lever set at 32 mm.
*2. This PT value is possible when the NC contacts are open
(OFF).
*3. This PT value is possible when the NO contacts are
closed (ON).
*4. Only for MBB models.
*5. Reference value for MBB models only.
*6. Reference value.
*7. For safe use, always make sure that the minimum values
or greater are provided.
(c)Copyright OMRON Corporation 2007 All Rights Reserved.
D4N
±1
48.2
41.3
±1
50 dia. × 8
(29.2)
rubber roller
±0.2
11
32 to 66R
20.5 × 20.5
27.5
21.5
2.15±0.05R
mounting holes
Stainless steel
lever
14.2
Conduit cap
30
+0.15
Two, 4
dia. holes
0
Depth: 5
12
Advertisement
Table of Contents
