Omron D4N Series Manual page 11

Snap-action (1NC/1NO) (2NC), Slow-action (2NC) (3NC)
Operating characteristics
Operating force OF max.
Release force RF min.
Pretravel PT max.
Overtravel OT min.
Movement differential MD max. *1
Operating position OP
Total travel TT *2
Direct opening travel DOT min. *3
Direct opening force DOF min. *3
Slow-action (1NC/1NO) (2NC/1NO)
Operating characteristics
Operating force OF max.
Release force RF min.
Pretravel PT max. *1
PT (2nd) *2
PT max. *3
PT (2nd) *4
Overtravel OT min.
Operating position OP
OP *5
Total travel TT *6
Direct opening travel DOT min. *7
Direct opening force DOF min. *7
http://www.ia.omron.com/
Model D4N-@131 D4N-@132
D4N-@231 D4N-@232
D4N-@B31 D4N-@B32
D4N-@D31 D4N-@D32
6.5 N 6.5 N
1.5 N 1.5 N
2 mm 2 mm
4 mm 4 mm
1 mm 1 mm
18.2 0.5 mm 28.6 0.8 mm 37 0.8 mm
(6 mm) (6 mm)
3.2 mm 3.2 mm
20 N 20 N
Model D4N-@A31 D4N-@A32
D4N-@C31 D4N-@C32
D4N-@E31 D4N-@E32
D4N-@F31 D4N-@F32
6.5 N 6.5 N
1.5 N 1.5 N
2 mm 2 mm
(2.9 mm) (2.9 mm)
2.8 mm 2.8 mm
(1 mm) (1 mm)
4 mm 4 mm
18.2 0.5 mm 28.6 0.8 mm 37 0.8 mm
17.4 0.5 mm 28 0.8 mm
(6 mm) (6 mm)
3.2 mm 3.2 mm
20 N 20 N
D4N-@162 D4N-@172
D4N-@262 D4N-@272
D4N-@B62 D4N-@B72
D4N-@D62 D4N-@D72
5.0 N 5.0 N
Note: Variation occurs in the simultaneity
0.8 N 0.8 N
4 mm 4 mm
5 mm 5 mm
1.5 mm 1.5 mm
*1. Only for snap-action models.
27 0.8 mm *2. Reference value.
*3. For safe use, always make sure that
(9 mm) (9 mm)
5.8 mm 4.8 mm
20 N 20 N
D4N-@A62 D4N-@A72
D4N-@C62 D4N-@C72
D4N-@E62 D4N-@E72
D4N-@F62 D4N-@F72
5.0 N 5.0 N
0.8 N 0.8 N
*1. These PT values are possible when
4 mm 4 mm
*2. These PT values are possible when
(5.2 mm) (4.3 mm)
4 mm 4 mm
*3. Only for MBB models.
(1.5 mm) (1.5 mm)
*4. Reference values for MBB models.
5 mm 5 mm
*5. Only for MBB models.
*6. Reference value.
27 0.8 mm
*7. For safe use, always make sure that
36 0.8 mm 26.1 0.8 mm
(9 mm) (9 mm)
5.8 mm 4.8 mm
20 N 20 N
(c)Copyright OMRON Corporation 2007 All Rights Reserved.
D4N
of contact opening/closing
operations of 2NC, 2NC/1NO, and
3NC contacts. Check contact
operation.
the minimum values or greater are
provided.
the NC contacts are open (OFF).
the NO contacts are closed (ON).
the minimum values or greater are
provided.
11