Safety Rules For Charger - Flexlite FLX6SB User Manual

serious personal injury, never allow the work light lens to
come in contact with anything.
 Check damaged parts. Before further use of this work light,
a part that is damaged should be carefully checked to
WARNING!
STAND
Do not install the light stand outside in a windy temperature. The stand can fall and injuries could result.
WARNING!
LED LIGHT
Do not stare into the beam or view directly with or without optical instruments.
WARNING!
Do not project the light towards traffic road, another person or any vehicle to prevent blindness. Doing so, may result in serious
injuries or death.

SAFETY RULES FOR CHARGER

WARNING!
READ AND UNDERSTAND ALL
INSTRUCTIONS.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious personal
injury.
 Before using battery adapter, read all instructions and
cautionary markings in this manual, on battery charger and
product using battery to prevent misuse of the products and
possible injury or damage.
NEVER RECHARGE BELOW
5ºC (41ºF)
CAUTION:
To reduce the risk of electric shock or damage to the charger
and battery; charge only batteries as specifically designated on
your adapter. Other types of batteries may burst, causing
personal injury or damage.
 Do not use charger outdoors or expose to wet or damp
conditions. Water entering adapter will increase the risk of
electric shock.
 Use of an attachment not recommended or sold by
another manufacturer may result in a risk of fire, electric
shock, or injury to persons. Following this rule will reduce
the risk of electric shock, fire, or serious personal injury.
 Do not abuse the cord of adapter. Never use the cord to
carry the adapter. Do not pull the charger cord rather than the
plug when disconnecting from receptacle. Damage to the
cord or charger could occur and create an electric shock
hazard. Replace damaged cords immediately.
 Make sure cord is located so that it will not be stepped on,
tripped over, come in contact with sharp edges or moving
parts or otherwise subjected to damage or stress. This will
reduce the risk of accidental falls, which could cause injury,
and damage to the cord, which could result in electric shock.
determine that it will operate properly and perform its
intended function. Do not use work light if it does not
function properly.
 Keep cord and adapter from heat to prevent damage to
housing or internal parts.
 Do not let gasoline, oils, petroleum-based products, etc.
come in contact with plastic parts. They contain chemicals
that can damage, weaken, or destroy plastic.
 An extension cord should not be used unless absolutely
necessary. Use of improper extension cord could result in a
risk of fire and electric shock. If extension cord must be used,
make sure:
 That pins on plug of extension cord are the same
number, size and shape as those of plug on charger.
 That extension cord is properly wired and in good
electrical condition; and
 That wire size is large enough for AC ampere rating of
adapter as specified below:
Cord Length (Feet)
Cord Size (AWG)
NOTE: AWG = American Wire Gauge
 Do not operate adapter with a damaged cord or plug,
which could cause shorting and electric shock. If damaged,
have the charger replaced by an authorized serviceman.
 Do not operate adapter if it has received a sharp blow,
been dropped, or otherwise damaged in any way. Take it
to an authorized serviceman for electrical check to determine
if the charger is in good working order.
 Do not disassemble adapter. Take it to an authorized
serviceman when service or repair is required. Incorrect
reassembly may result in a risk of electric shock or fire.
 Unplug adapter from outlet before attempting any
maintenance or cleaning to reduce the risk of electric
shock.
 Disconnect adapter from the power supply when not in
use. This will reduce the risk of electric shock or damage to
the charger if metal items should fall into the opening. It also
will help prevent damage to the charger during a power
surge.
 Risk of electric shock. Do not touch uninsulated portion of
output connector.
 Save these instructions. Refer to them frequently and use
them to instruct others who may use this work light. If you
loan someone this work light, loan them these instructions
also to prevent misuse of the product and possible injury.
25´ 50´ 100´
16 16 16
3