Safety Rules For Charger - Flexlite FLX24L2H Operator's Manual

If wrapped or in contact with fabrics, the worklight lens
can produce sufficient heat to melt some fabrics. To avoid
serious personal injury, never allow the worklight lens to
come in contact with anything.
WARNING!
MAGNETIC HAZARDS
Strong magnetic forces pose a potential hazard to people who wear heart implant devices and they can destroy magnetic media
data files (such as computer hard drives). Visually warning people of the existence of strong magnetic fields is necessary when
such fields are generated by equipment.
WARNING!
LED LIGHT
Do not stare into the beam or view directly with or without optical instruments.
WARNING!
This light system needs a constant air flow to cool down, NEVER leave the light turned on when not in motion;
otherwise the light will becomes hot and can cause injury, fire or damages. Do not project the light towards traffic
road, another person or any vehicle to prevent blindness. Doing so, may result in serious injuries or death.

SAFETY RULES FOR CHARGER

WARNING!
READ AND
INSTRUCTIONS.
Failure to follow all instructions listed below
may result in electric shock, fire and/or serious
personal injury.
Before using battery charger, read all instructions
and cautionary markings in this manual, on battery
charger and product using battery to prevent misuse of
the products and possible injury or damage.
CAUTION:
To reduce the risk of electric shock or damage to
the charger and battery; charge only batteries as
specifically designated on your charger. Other
types of batteries may burst, causing personal
injury or damage.
Do not use charger outdoors or expose to wet or damp
conditions. Water entering charger will increase the risk of
electric shock.
Use of an attachment not recommended or sold by
another manufacturer may result in a risk of fire, electric
shock, or injury to persons. Following this rule will reduce
the risk of electric shock, fire, or serious personal injury.
Do not abuse cord or charger. Never use the cord to carry
the charger. Do not pull the charger cord rather than the plug
when disconnecting from receptacle. Damage to the cord or
charger could occur and create an electric shock hazard.
Replace damaged cords immediately.
Make sure cord is located so that it will not be stepped on,
tripped over, come in contact with sharp edges or moving
parts or otherwise subjected to damage or stress. This will
reduce the risk of accidental falls, which could cause injury,
and damage to the cord, which could result in electric shock.
UNDERSTAND ALL
Check damaged parts. Before further use of this worklight,
a part that is damaged should be carefully checked to
determine that it will operate properly and perform its
intended function. Do not use worklight if it does not
function properly.
Keep cord and charger from heat to prevent damage to
housing or internal parts.
Do not let gasoline, oils, petroleum-based products, etc.
come in contact with plastic parts. They contain chemicals
that can damage, weaken, or destroy plastic.
An extension cord should not be used unless absolutely
necessary. Use of improper extension cord could result in a
risk of fire and electric shock. If extension cord must be used,
make sure:
That pins on plug of extension cord are the same
number, size and shape as those of plug on charger.
That extension cord is properly wired and in good
electrical condition;
That wire size is large enough for AC ampere rating of
charger as specified below:
Cord Length (Feet)
Cord Size (AWG)
NOTE: AWG = American Wire Gauge
Do not operate charger with a damaged cord or plug,
which could cause shorting and electric shock. If damaged,
have the charger replaced by an authorized serviceman.
Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way. Take it
to an authorized serviceman for electrical check to determine
if the charger is in good working order.
Do not disassemble charger. Take it to an authorized
serviceman when service or repair is required. Incorrect
reassembly may result in a risk of electric shock or fire.
Unplug charger from outlet before attempting any
maintenance or cleaning to reduce the risk of electric
shock.
Disconnect charger from the power supply when not in
use.
This will reduce the risk of electric shock or damage to the
charger if metal items should fall into the opening. It also will help
prevent damage to the charger during a power surge.
Risk of electric shock. Do not touch uninsulated portion of
output connector.
Save these instructions.
Refer to them frequently and use them
to instruct others who may use this worklight. If you loan someone
this worklight, loan them these instructions also to prevent misuse of
the product and possible injury.
25´ 50´ 100´
16 16 16
3