Advertisement
No
Item
From NavNet vx2: GD-1920C-BB to TZT2BB
If the monitors are also compatible with HDMI...:
Connect to the TZT2BB processor MPU-004 with an HDMI cable.
If the monitors are also compatible with DVI-D...:
Connect to the TZT2BB processor MPU-004 with a DVI-HDMI adapter.
If the monitors are compatible with VGA (RGB) only:
Replace with a monitor compatible with HDMI or DVI-D.
IMPORTANT:
Make sure that these monitors are compatible with the resolution of
1920×1080 (FHD), 1280×1024 (SVGA), and 1024×768 (XGA), which
are output from the TZT2BB.
10
Ethernet Cable
The Ethernet cable is fit with a unique connector, not RJ45, and cannot
be used in the NavNet TZtouch2 (TZT2BB) network.
11
Network Sensors
DFF1, DFF3, FA-30, and FA-50 can be utilized in the NavNet TZtouch2
(Ethernet)
network. Radar antennas, BBFF1 (1 kW Fish Finder sensor), and BBFF3
(3 kW Fish Finder sensor) are NOT compatible with the NavNet
TZtouch2 network. Replace with the latest series.
Radar: Replace with DRS series
BBFF1: Replace with DFF1 or BBDS1 or connect the transducer to the
built-in transducer port of TZTL12F/15F or TZT2BB.
BBFF3: Replace with DFF3
12
NMEA2000
NavNet vx2 models including the GD-1920C-BB are not compatible with
Devices
NMEA2000 interface.
13
NMEA0183
Input NMEA0183 sensors to the TZT2BB network via an NMEA converter
Devices
or replace them with NMEA2000 sensors.
14
Video Input
The GD-1920C-BB has one (1) RCA port. An existing analog camera can
be utilized on the TZT2BB.
15
Transducers
600 W and 1 kW transducers work with the built-in Fish Finder of
for Fish Finders
TZTL12F/15F and TZT2BB.
The following sections highlights changes in wiring and hardware components for retrofit.
From NavNet 3D: MFDBB to TZT2BB
If the monitors are also compatible with HDMI...:
Connect to the TZT2BB processor MPU-004 with an HDMI cable.
IMPORTANT:
Make sure that these monitors are compatible with the resolution of
1920×1080 (FHD), 1280×1024 (SVGA), and 1024×768 (XGA), which are
output from the TZT2BB.
The Ethernet cable connected to the MFDBB Ethernet ports (RJ45) can be
utilized for the TZT2BB.
Ethernet sensors in the NavNet 3D network are compatible with NavNet
TZtouch2.
Note:
The MFDBB has the DRS power port for the DRS2D/4D/4A/6A/12A, but the
TZT2BB does not. Use the PSU-017 (supporting DRS2D/4D) and PSU-012
(supporting DRS2D/4D/DRS4A/6A/12A) to utilize the DRS series in the
NavNet TZtouch2 network.
NMEA2000 devices can be utilized.
Input NMEA0183 sensors to the TZT2BB network via an NMEA converter or
replace them with NMEA2000 sensors.
The MFDBB has four (4) BNC ports. Connectors should be adapted to RCA
for the TZT2BB. Note that the TZT2BB has two (2) RCA ports.
-
23
From NavNet TZtouch: TZTBB to TZT2BB
adapter. Connect a USB cable for touch interface.
If the monitors are also compatible with HDMI...:
Connect to the TZT2BB processor MPU-002 with an HDMI cable.
IMPORTANT:
Make sure that these monitors are compatible with the resolution
of 1920×1080 (FHD), 1280×1024 (SVGA), and 1024×768
(XGA), which are output from the TZT2BB.
The Ethernet cable (MOD-WPAS0001-030+) connected to the
TZTBB Ethernet ports is equipped with waterproof cap. The
connector with waterproof cap does not fit on the TZT2BB USB
connector at the pigtail cable. Use the Ethernet cable with the
RJ45 connector fitted. (If the Ethernet cable with the RJ45
connector, less waterproof cap, is used with the TZTBB, it can be
utilized with the TZT2BB.)
Ethernet sensors in the NavNet TZtouch network are all
compatible with the NavNet TZtouch2 network.
NMEA2000 devices can be utilized.
Input/output NMEA0183 sensors to/from the TZT2BB network
via an NMEA converter or replace them with NMEA2000 sensors.
The TZTBB has two (2) RCA connectors. Existing analog cameras
can be utilized on the TZT2BB.
-
Advertisement
