MIDI CC Implemention Chart
Function
CC
Osc2 Fine Detune
31
FEG Amount
32
Morph
33
Cutoff
34
Reso
35
SYNC: 0-7 = 1/16 / 8-15 = 1/8 / 16-23 = 3/16 / 24-31 = 1/4 /
LFO1 Rate
36
32-39 = 3/8 / 40-47 = 1/2 / 48-55 = 3/4 / 56-63 = 1 / 64-71 = 3/2
/ 72-79 = 2 / 80-87 = 3 / 88-95 = 4 / 96-103 = 6 /104-111 = 8 /
LFO1 Depth
37
0-32 Sine to Triangle / 33-64 - Triangle to Sawtooth / 65-96 -
LFO1 Shape
39
Sawtooth to Square / 97-127 - Square to Sample and Hold
Octave
40
MEG Attack
43
MEG Decay
44
MEG Sustain
45
MEG Release
46
NO SYNC: 0-63 = 0-32Hz Free / 64-71 Root/8 / 72-79 Root/4 /
80-87 Root/2 / 88-95 Root / 96-103 Root*1.5 /104-111 Root*2 /
LFO2 Rate
47
SYNC: 0-7 = 1/16 / 8-15 = 1/8 / 16-23 =1/4 / 24-31 =1/2 / 32-39
= 1 / 40-47 = 5/4 / 48-55 =2 / 56-63 = 4 (Cycles per beat)
LFO2 Depth
48
MEG Amount
49
0-32 Sine to Triangle / 33-64 - Triangle to Sawtooth / 65-96 -
LFO2 Shape
50
Sawtooth to Square / 97-127 - Square to Sample and Hold
AEG Amount
51
LFO1 MIDI Sync
52
Ring Mod
53
LFO2 MIDI Sync
54
Delay MIDI Sync
55
38
Values
-/+ 1 Semitone
63 (0) +/- 63
0 = LP / 64 = BP / 127 = HP
0Hz - 22kHz
None - Full
NO SYNC: 0-127 = 0.02Hz - 32Hz
112-119 = 12 / 120-127 = 16
63 (0) +/- 63
Octaves -2 to +4
0 - 4 Seconds
0 - 4 Seconds
0 - 1
0 - 4 Seconds
112-119 Root*2.5 / 120-127 Root*3
63 (0) +/- 63
63 (0) +/- 63
63 (0) +/- 63
0 - 63 = OFF / 64 - 127 = ON
0 - 63 = OFF / 64 - 127 = ON
0 - 63 = OFF / 64 - 127 = ON
0 - 63 = OFF / 64 - 127 = ON
MIDI CC Implemention Chart
Function
CC
LFO1 Mode
56
LFO2 Mode
57
Arp Status
58
Arp Octave
59
0 - 31 1Oct / 32-63 2Oct / 64-95 3Oct / 96-127 4Octaves
0-20 = Forwards, 21-41 = Backwards, 42-62 = Pendulum, 63 - 83
Arp Direction
60
= Note Forwards, 84 - 104 = Note Backwards, 105-127 = Note
Value / 16 = 1/32nd, 1/24th, 1/16th, 1/12th, 1/8th, 1/6th, 1/4th,
Arp Division
61
Velo Depth
62
Note Depth
63
Sustain Pedal
64
Aftertouch Depth
65
Ext Depth
66
Sequence Length
67
0 - 31 = 1 Bar / 32-63 = 2 Bars / 64-95 = 4 Bars / 96-127 = 8 Bars
Sequence Hold
70
To Skulpt: 127 sets loop start point, 0 sets loop stop point. From
Sequence Loop
71
Skulpt: 127 is currently looping, 0 is not looping
Transpose
75
Swing
78
Anim 1 CC
80
Anim 2 CC
81
Anim 3 CC
82
Anim 4 CC
83
All Envelope Attack
84
All Envelope Decay
85
All Envelope Sustain
86
All Envelope Release
87
Values
0-41 Retrig / 42-83 Free / 84-127 Single
0-41 Retrig / 42-83 Free / 84-127 Single
0 - 63 = OFF / 64 - 127 = ON
Pendulum
1/2nd
63 (0) +/- 63
63 (0) +/- 63
0 - 63 = OFF / 64 - 127 = ON
63 (0) +/- 63
63 (0) +/- 63
0 - 63 = OFF / 64 - 127 = ON
-24 to +36 sent as (value + 24) * 2
0 - 127
CC number of new destination
CC number of new destination
CC number of new destination
CC number of new destination
0 - 4 Seconds
0 - 4 Seconds
0 - 1
0 - 4 Seconds
39
Need help?
Do you have a question about the SKULPTsynth SE and is the answer not in the manual?
Questions and answers