Related Manuals for Plymovent MDB GO
Summary of Contents for Plymovent MDB GO
- Page 1 Central filter system | modular | MDB Installation and user manual www.plymovent.com...
-
Page 2: Table Of Contents
To improve comprehension for people whose first language is not English, we have written parts of this manual in Simplified Technical English (STE). STE is a controlled language originally developed for aerospace industry maintenance manuals. It offers a carefully limited and standardized subset of English, along with specific writing rules. 0000100513/050719/C MDB GO | MDB PRO... -
Page 3: Preface
There are two ways to control the filter cleaning system of the number of filter cartridges MDB and the connected fan. - Suffixes: - H: horizontal layout - V: vertical layout - no suffix: square layout 0000100513/050719/C MDB GO | MDB PRO... -
Page 4: Product Description
4-5 bar (60-75 PSI) Compressed air push-in fitting: connection - in: ⅜ in. - out: 12 mm Compressed air 40-50 nl/pulse (1.4-1.8 ft³/ consumption pulse) Electrical data Input voltage for 24 VDC magnetic valves Approvals and certifications 0000100513/050719/C MDB GO | MDB PRO... -
Page 5: Safety
MDB and to control the connected fan. perfect condition in accordance with its intended use and the instructions explained in the user manual. - MDB GO: ControlGo | Intelligent control panel for basic fan/ filter control Technical specifications Do not change the specifications given in this manual. -
Page 6: Installation
- Check the working environment. Do not allow unauthorised Refer to Fig. II on page 17 for the scope of supply persons to enter the working environment. of each modular component package. 0000100513/050719/C MDB GO | MDB PRO... - Page 7 Fig. 4.5 Hopper + cover plate Fastening Fig. 4.2 Air outlet module • Tighten the bolts of the entire frame (refer to Fig. 4.1). Note: the “open” sides of the bars are on the outside 0000100513/050719/C MDB GO | MDB PRO...
- Page 8 The number depends on the system • Make sure that the jigsaws tightly fit. configuration. No nuts involved. The dustbin lift has some tolerance Do not worry about a slight misalignment of the seal holes 0000100513/050719/C MDB GO | MDB PRO...
- Page 9 Leave the filter module on the pallet to avoid damage Do not shift the filter module to avoid damage to the seals and backing material Do not worry about a slight misalignment of the seal holes 0000100513/050719/C MDB GO | MDB PRO...
- Page 10 After approx. 60 seconds SealApplicator lubricant loses its functions and you cannot shift anymore. Therefore, do not install multiple filter modules or stacks of filter modules. This takes simply too much time. 10. Start with the horizontal surfaces 0000100513/050719/C MDB GO | MDB PRO...
- Page 11 4.5.1 Deflector plates Fig. 4.21 Filter module on first filter module To optimize the airflow and to protect the filter cartridges, you <60 s must install two deflector plates behind each air inlet module. 0000100513/050719/C MDB GO | MDB PRO...
- Page 12 Put one cover plate within 60 seconds on the filter module. • (4) Attach the cover plate with the flange screws. Fig. 4.25 Air inlet/outlet module(s) • Repeat this procedure for the remaining cover plates. 0000100513/050719/C MDB GO | MDB PRO...
- Page 13 Are the filter cartridges installed in the right way? Is the dustbin correctly installed? Is it attached to the hopper with the quick connect clamp? 11. Dosing speed: approx. 1 kg (2.2 lbs.) per minute 0000100513/050719/C MDB GO | MDB PRO >2 mm...
-
Page 14: Use
Control The way to control the MDB system, depends on the selected MDB type; - MDB GO: refer to the installation and user manual of the ControlGo - MDB PRO: refer to the installation manual and the online user manual of the ControlPro MAINTENANCE Fig. -
Page 15: Troubleshooting
Obey the safety regulations that are written in - disconnect it from the mains chapter 3 when you carry out the activities below. - disconnect it from the compressed air - clean the outside 0000100513/050719/C MDB GO | MDB PRO... -
Page 16: Ce Declaration
Considering the above, the installer will be responsible for completing the installation and issuing the final CE Declaration of Conformity. 0000100513/050719/C MDB GO | MDB PRO... - Page 17 16952 MDB-36 PTFE/15 5813 16200 43200 9535 25428 PTFE/10 5172 14400 38400 8476 22602 MDB-48 PTFE/15 7758 21600 57600 12714 33903 PTFE/10 6896 19200 51200 11301 30136 MDB-64 PTFE/15 10344 28880 76800 16952 45204 0000100513/050719/C MDB GO | MDB PRO...
- Page 18 MDB-HOPPER Fig. II Scope of supply MDB-FRAME M8x16 DB-80 M10x40 M8x16 M8x16 M10x40 M10x40 MDB-BM/2 MDB seal assembly Seal set MDB-BM/2 Seal set MDB-BM/4 MDB-BM/4 Spare seal set MDB SealApplicator M8x16 M8x16 M10x40 M10x40 0000100513/050719/C MDB GO | MDB PRO...
- Page 19 Assembly sequence of MDB system; - if applicable: install the MDB-BM/2 module(s) first - layer by layer - from left to right - one filter module at a time MDB-INLET/315 MDB-OUTLET/315 MDB-INLET/400 MDB-OUTLET/400 MDB-INLET/500 MDB-OUTLET/500 0000100513/050719/C MDB GO | MDB PRO...
- Page 20 DB-80 / Dustbin 80 litres, incl. lifting pin and handles 0000102666 Cover plate for filter cartridge CART Filter cartridge, incl. facemask, disposable gloves and plastic sack with seal for collection and disposal of the used filter cartridge 0000102675 Filter cartridge holder 0000100513/050719/C MDB GO | MDB PRO...
- Page 21 0000100513/050719/C MDB GO | MDB PRO www.plymovent.com...
Need help?
Do you have a question about the MDB GO and is the answer not in the manual?
Questions and answers