Advertisement
Quick Links
Advertisement
Related Manuals for Graco VISCOUNT I 3000
Summary of Contents for Graco VISCOUNT I 3000
- Page 1 Parts...
- Page 2 FOR PROFESSIONAL USE ONLY. OBSERVE ALL WARNINGS. Read and understand all instruction manuals before operating equipment...., . . i........
- Page 3 Fluid Compatibilit General Safety BE SURE that all Any misuse of the dispensing equipment or accessories, such wetted parts TECHNICAL DATA patible with the shown in the as overpressurizing, modifying parts, using incompatible shown on page 12. Always read the fluid and solvent chemicals and fluids, or using worn or damaged parts, can turer’s literature before using them in your system.
- Page 4 HYDRAULIC INLET HYDRAULIC OUTLET H Pressure Reducing Valve M Hydraulic Power Supply K E Y Hydraulic Return Line N Ground Wire Shutoff Valve Accumulator A Fluid Hose to Gun K Drain Line P Wet cup B Fluid Drain Valve Pressure Gauge C Suction Hose Flow Control Valve L Hydraulic Supply Line...
-
Page 5: Operation
, . , * , . , . . + . * .., . , . . , A ..,, . , , , , , , , , , * < . , , , ... - Page 6 Carefully monitor the fluid supply. If the pump empties Hydraulic leaking at the reciprocator fittings. All of the the supply container, air is sucked into the pump, causing fittings (7,8 and 10) going into the upper and lower cylin- it to run too fast and to be damaged. If the pump runs too der caps are self-sealing and have replaceable o-rings.
- Page 7 NOTE: Packing Repair 220-397 is available. Use all the parts in the kit for best results, even if the old ones still look good. An asterisk behind a reference number in the text, for example (114*), indicates that the part is included in the repair kit.
- Page 8 Intake Valve (See Fig 5) Unscrew the intake valve housing (119) and remove the ball stop pin (1 IO), retainer (112), o-ring (1 1 I*), ball guide (116) and ball (103*). Reassemble the intake valve with a new o-ring and ball.
- Page 9 ..: < . y . < <<<r , . < PARTS DRAWING ~~~~~~~~~~ ..A. . 5 v..< . . . A : . : . : . : . : . : . : . : . : . : . : . ~ .
- Page 10 Model 221-080 Viscount I 3000 Pump Series A, Stubby Length NO. PART NO. DESCRIPTION SCREW, math PLATE, identification 179-884 100-133 LOCKWASHER 217-222 VISCOUNT I reciprocator See manual 307-654 for parts ADAPTER, straight thd; 107-195 Includes I of item 24 ELBOW, straight thd,...
- Page 11 6 feet (1.9 m) long (759 mm) HYDRAULIC SHUTOFF VALVES 102-644 102-645 1” npt(f) for return line GRACO-APPROVED HYDRAULIC FLUID 169-236 5 gallon (20 liter) 207-428 1 gallon (3.8 liter) SUCTION HOSE 214-961 For petroleum base solvent flushing and water base fluids.
-
Page 12: Warranty
EVERY FORM OF LIABILITY FOR DIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES OR LOSS IS EXPRESSLY EXCLUDED AND DENIED. IN NO CASE SHALL GRACO’S LIABILITY EXCEED THE AMOUNT OF THE PURCHASE PRICE. ANY ACTION FOR BREACH OF WARRANTY MUST BE BROUGHT WITHIN TWO (2) YEARS OF THE DATE OF SALE. - Page 13 3X7–623 REV F SUPERSEDES REV E PARTS CHANGE NOTICE Some parts in Rev. E of manual 307–623 have changed but have not yet been changed in the instruction manual. Please note the changes below and mark them in your manual or keep this sheet with your manual. Assembly Replaced by Changed...
Need help?
Do you have a question about the VISCOUNT I 3000 and is the answer not in the manual?
Questions and answers