IDS HYYP Manual

IDS HYYP Manual

Ip connect with wifi module

Advertisement

Quick Links

IDS HYYP IP Connect
With WiFi Module
Introduction
The IDS HYYP IP Connect Module is a plug on module for the X-Series alarm panels. The HYYP
IP Connect Module will enable your X-Series panel to communicate with the HYYP platform
(monthly charges apply)
allowing it to report to your HYYP Base Station
and the HYYP Home
mobile app.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HYYP and is the answer not in the manual?

Questions and answers

Naomi
April 12, 2025

I have 3 partitions on my alarm. House Beams (outside) Flat House and Beams have same pin/code Flat as different code When i set up a user on my app for the person living in the flat i stored the pin/code as part of the setup so that they dont have to enter the code every time they arm/disarm. They have access to the Beams and Flat but not the House partition So in the profile that ive set up are my main code and the code for the flat. When they now arm/disarm the flat they arm/disarm the house at the same time. So i the morning when they arm the flat they fully arm the house that was on sleep. HELP PLEASE!

1 comments:
Mr. Anderson
April 12, 2025

To prevent the IDS HYYP alarm system from arming the House partition when arming the Flat partition, you need to arm only the specific partition you want. Select only the Flat partition in the app. Each partition (e.g., House or Flat) is armed individually, so if you arm only the Flat partition, the House partition will remain disarmed.

This answer is automatically generated

R J Maharaj
July 3, 2025

My unit is frequently offline. It resumes the online condition without intervention, but then goes offline again

Summary of Contents for IDS HYYP

  • Page 1 IDS HYYP IP Connect With WiFi Module Introduction The IDS HYYP IP Connect Module is a plug on module for the X-Series alarm panels. The HYYP IP Connect Module will enable your X-Series panel to communicate with the HYYP platform (monthly charges apply)
  • Page 2 1.1. Wiring Connect the HYYP IP Connect Module 12v input to the TX connectors of the X-Series panel. Be sure to connect the 12V to positive and GND to Negative. Connect the provided serial cable from the serial connector on the X-series panel to the serial connector on the HYYP IP Connect Module.
  • Page 3 To install the HYYP Home App go to the Google Play Store and search for HYYP Home. And click install. Once installed open the HYYP Home App, the first time you open the app you will be asked to sign up, or login if you have already registered.
  • Page 4 2.2. Adding a site Once registered you will be given a HYYP ID and asked if you have a HYYP IP Connect to connect. Click ‘I have a new HYYP Hub’. Give your HYYP IP Conect a name and choose a site colour.
  • Page 5 Enter the HYYP IP Connects Unique ID number or scan the unique barcode on the HYYP IP Connect. Click ‘Continue’. To add the HYYP IP Connect Module to the HYYP Home app you must enter location 196 when the app asks you to synchronise the device.
  • Page 6 Network Comms LED will flash when it’s communicating on the network. If the Server Auth and Network Comms LEDs continue to flash the same number then there is an error on the HYYP IP Connect Module. You can determine the error by the amount of times the LEDs flash.
  • Page 7 3.2. IP Ports These are the ports that are needed for the HYYP IP Connect to connect to the HYYP servers. None of these ports or IP addresses must be blocked. 1) Request DHCP server to provide IP address details 2) DNS lookup of tick.meraka.csir.co.za...

Table of Contents

Save PDF