Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Briggs & Stratton FB13250BS
Summary of Contents for Briggs & Stratton FB13250BS
- Page 1 OPERATOR’S MANUAL Field and Brush Mower Mfg. No. Model No. 7085922 FB13250BS 7085923 GM2515KAW 7085924 GM2513H -4415 Description Briggs (13), Hydro-Drive Kawasaki (15), Hydro-Drive Honda (13), Hydro-Drive Manual No. 7101186 (I.R. 11/7/2006) TP 100-5243-IR-WB-SNGF...
-
Page 2: Table Of Contents
Identification Numbers...1 Safety Rules & Information...2 Safety Decals ...4 Features & Controls ...6 Control Functions ...6 Operating the Mower...7 Starting the Engine ...7 Engaging the Transmission ...7 Engaging/Disengaging the Cutting Blade ...9 To Adjust Cutting Height ...10 Storage ...10 Regular Maintenance ...11 Lubrication ...11 Tire Pressure ...12 Battery Service...12... -
Page 3: Safety Rules & Information
Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. This mowing deck is capable of amputating hands and feet and throwing objects. The triangle in text signi- fies important cautions or warnings which must be followed. -
Page 4: Safety Rules And Information
SLOPE OPERATION WARNING Never operate on slopes greater than 17.6 percent (10°) which is a rise of 3-1/2 feet (106 cm) vertically in 20 feet (607 cm) horizontally. Select slow ground speed before driving onto slope. In addition to front and rear weights, use extra caution when operating on slopes with rear-mounted grass catcher. -
Page 5: Safety Decals
Safety Rules & Information SERVICE AND MAINTENANCE • Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. Use only an approved container. Never remove gas cap or add fuel with the engine running. Allow engine to cool before refu- eling. -
Page 6: Safety And Instructional Decals
Decal - Warning (7028490) Important Safety Operating Instructions. Read and understand before operating machine Decal - Engine Throttle Control (7029167) Models - All mowers DANGER KEEP HANDS and FEET AWAY Decal - Danger: Dismemberment (7013010) This mower deck can amputate limbs. Keep hands and feet away from blades. -
Page 7: Features & Controls
Features & Controls Please take a moment and familiarize yourself with the name, location, and function of these controls so that you will better understand the safety and operat- ing instructions provided in this manual. CONTROL FUNCTIONS The information below briefly describes the function of individual controls. -
Page 8: Operating The Mower
STARTING THE ENGINE NOTE - The procedures outlined within this section are general guidelines, and are in no way meant to replace or supercede engine manufacturer's operating instruc- tions. In order to obtain optimum performance from your engine, refer to your engine manual. Before Starting Engine: •... - Page 9 Operating the Mower To Propel Unit Forward: IMPORTANT NOTE IN CASE OF EMERGENCY, SUCH AS LOSS OF CONTROL OR POTENTIAL COLLISION, RELEASE TRACTION DRIVE ENGAGEMENT BAR. THIS WILL IMMEDI- ATELY DISENGAGE THE TRANSMISSION AND STOP MOWER MOVEMENT. THE ENGINE WILL CONTINUE TO RUN.
-
Page 10: Engaging/Disengaging The Cutting Blade
ENGAGING/DISENGAGING THE CUTTING BLADE DANGER Do not pass by or stand on the discharge side of brush mower with its engine running and blade engaged. To Engage Cutting Blade: • Push Blade Engagement Lever forward and then to the right until lever locks into place (Figure 7). WARNING Engaging cutting blade will activate engine safety kill feature. -
Page 11: To Adjust Cutting Height
Operating the Mower TO ADJUST CUTTING HEIGHT The front skids on the brush cutter have 3 sets of holes (Figure 9) for height adjustment: – Top holes - 3 " cutting depth – Center holes - 4" cutting depth – Bottom holes - 4 "... -
Page 12: Regular Maintenance
LUBRICATION Service Interval: Every 25 Hours Lubricate the unit at the locations shown in Figure 10 as well as the lubrication points listed. Generally, all moving parts should be oiled where contact is made with other parts. Keep oil and grease off belts and pulleys. Wipe surfaces clean before and after lubrication. -
Page 13: Tire Pressure
Regular Maintenance TIRE PRESSURE Tire pressure is 20 psi (1.4 bar). BATTERY SERVICE WARNING When removing or installing battery cables, disconnect the negative cable FIRST and reconnect it LAST. If not done in this order, the positive terminal can be shorted to the frame by a tool. -
Page 14: Servicing The Mower Blades
SERVICING THE MOWER BLADES WARNING For your personal safety, do not handle the sharp mower blades with bare hands. Careless or improper handling of blades may result in serious injury. Service Interval: Every 100 Hours or As Required 1. Raise the front end of the brush mower and securely support in the raised position. -
Page 15: Troubleshooting, Adjustment And Service
Troubleshooting, Adjustment, & Service TROUBLESHOOTING PROBLEM Engine will not turnover or start. Engine will not stay running while operating machine Engine starts hard or runs poorly. Engine knocks. Excessive oil consumption. Engine exhaust is black. Engine runs, but mower will not drive. - Page 16 Troubleshooting Cont. Blade will not engage. Blade will not disengage or Blade stop time over 5 seconds. Mower drive belt slips. Mower cut is uneven. Mower cut is rough looking. Excessive mower vibration. Excessive belt wear or breakage. Troubleshooting, Adjustment & Service 1.
-
Page 17: Travel Control Adjustment
Troubleshooting, Adjustment, & Service TRAVEL CONTROL ADJUSTMENT Serial Number 0-011903999 1. The Travel Control engagement bars (A, Figure 16a) should be an equal distance from the Upper Handle Bar. If they are not, adjust their position. 2. Loosen the wing nut locknut (D) and rotate control rod (C) until engagement bars are properly adjusted. -
Page 18: Blade Clutch Adjustment
BLADE CLUTCH ADJUSTMENT WARNING Shut off engine before attempting this adjustment procedure. If the mower blade does not stop running when the blade clutch lever is in the DISENGAGED position, does not run at full speed, adjust the Blade Clutch tension. 1. -
Page 19: Blade Brake Adjustment
Troubleshooting, Adjustment, & Service BLADE BRAKE ADJUSTMENT WARNING • DO NOT place hands or feet under mower deck and away from blade. • This machine is capable of throwing objects and debris. Keep bystanders away. • DO NOT touch any rotating parts (pulleys, belts, etc.). -
Page 20: Traction Drive Belt Adjustment
TRACTION DRIVE BELT ADJUSTMENT If the mower drive is not functioning properly, the drive belt may need to be adjusted; For S/N 0 - 071601075 The traction drive belt tension is adjusted by a bolt and screw system. To adjust belt tension: 1. -
Page 21: Mower Belt Replacement
Troubleshooting, Adjustment & Service MOWER BELT REPLACEMENT To replace the mower blade drive belt; NOTE - The traction drive belt will have to be removed before the mower blade belt can be removed. 1. Remove clutch cover plate (A, Figure 23). 2. -
Page 22: Specifications
NOTE: Specifications are correct at time of printing and are subject to change without notice. * Actual sustained engine power will likely be lower due to operating limitations and environmental factors. See ‘Engine Power Rating Information’ on page 1 for further information. ENGINE BRIGGS Engine *... - Page 23 Notes...
- Page 24 535 Macon Street/PO Box 777 McDonough, GA 30253 Briggs & Stratton Yard Power Products Group Copyright © 2006, Briggs & Stratton Corporation Milwaukee, WI, USA. All Rights Reserved.