Snapper 7800428 Parts Manual page 5

Handles and Controls
Item Part No
1 7074411
2 7074156
3 7033985
4 7033986
5 7074418
6 7034872
7 7034608
7 7102593
7 7078078
8 7074473
9 7028407
10 7034604
11 7012121
12 7012122
13 7074003
14 7024641
15 7073822
16 7013849
17 7073913
18 7074140
18 7074469
18 7073826
19 7900067
20 7091130
21 7091904
22 7090538
23 7012114
24 7090595
25 7091601
26 7091575
27 7074113
28 7091606
29 7023813
30 7091189
31 7035744
31 720727
32 7079577
33 7090053
34 7091576
35 7090505
36 7014343
37 7023792
38 7091020
Footnotes:
NOTE: * Part number and revision is stamped on cable.
21"STEEL DECK WALK BEHIND MOWERS
SERIES 20
Qty Description
1 HANDLE, Upper
1 HANDLE, Middle
1 HANDLE, Lower LH (Adjustable)
1 HANDLE, Lower RH (Adjustable) used on 7800430 & 7800492
1 BAIL, OPC Control
1 CLIP, Zone Control
1 * CABLE, Zone Control (52-63/64" Long) used on 7800425, 7800428, 7800437, 7800596,
7800597 & 7800602
1 * CABLE, Zone Control (52-21/32" Long) used on 7800424, 7800552, 7800553, 7800554 &
7800555
1 * CABLE, Zone Control (50-31/64" Long) used on 7800427 & 7800432
1 HANDLE, Clutch
1 GRIP, International Symbol
1 CABLE, Clutch Control (41-1/4" Long)
1 COVER, Vinyl
1 SPRING, Clutch - 21S
1 BRACKET, Shift
2 TIE, Wire, 1.29 long, black
1 BRACKET, Bell Crank
1 SPACER, .33 x .63 x .156
1 BELL CRANK
1 CONTROL PANEL (w/o Electrical Switch Hole) Used on Manual Start Models
1 CONTROL PANEL (w/Electrical Switch Hole) Used on electric start models
1 CONTROL PANEL (w/o wheel drive slot) used on 7800428, 7800437 & 7800596
4 SCREW, 1/4-20 x 1/2" Pan Head Self-Tap (Torx)
2 WASHER, .33 x .88 x .09 Flat
1 SCREW, 5/16-18 x 7/8" Hex Head Cap, GR 5
1 TEENUT, 5/16-18
1 BUSHING, Differential, .328 x .625 x .41
2 BOLT, 5/16-18 x 3/4" Hex Flange Lock GR 5
2 NUT, 5/16-18 Hex Flange Lock, GR 5
1 NUT, 5/16-18 Hex Center Lock
1 LEVER, Shift
1 NUT, 5/16-24 Hex Center Lock GR 5
1 CLIP, Wiring Harness
4 SCREW, 5/16-18 x 1-7/8" Curved Head GR 2
4 KNOB, 5/16-18 Wing (Black)
4 KNOB, 5/16-18 Wing (Black) Briggs part
2 SCREW, 1/4-20 x 1-1/2" Hex Head Cap GR 5
5 WASHER, 1/4" Internal Tooth Lock
3 NUT, 1/4-20 Hex
1 SCREW, 1/4-20 x 2" Hex Head Cap, GR 5
2 BUSHING, .27 x .35 x .4 Flange
1 PIN, 1/4 x 1-1/2"
1 PUSH-NUT, 1/4"
5
Manual No. 7006477