Table of Contents
Advertisement
U N D E R B A R R E F R I G E R A T I O N
Cabinet Setup
Shelf Installation
Procedure
1. Hook the shelf clips into the shelf standards. See fig. 1.
2. Push up on the bottom of the clip. See fig. 2.
NOTE: You may need to squeeze or twist the bottom of the
shelf clip for proper installation. Position all four shelf clips
equal in distance from the floor for flat shelves.
3. Ensure the shelf clip is not loose or able to wiggle out of the
shelf standard. See figs. 3 and 4.
4. Place the shelves on the shelf clips with the cross support bars
facing down.
NOTE: Be sure all shelf corners are properly seated.
Installation Tips
• Install all the shelf clips before installing any shelves.
• Start at the bottom shelf and work your way up.
• Always lay the back of each shelf down on the rear clips before
the front.
WARNING
– DO NOT use pliers or
any crimping tools when installing
shelf clips. Altering shelf clips in any
way can lead to shelving instability.
Fig. 1.
Installing top tab of shelf clip.
Fig. 2.
The bottom tab of the shelf clip
will fit tightly
Fig. 3.
Fig. 4.
You may need to squeeze or twist
Installed shelf clip..
the bottom of the shelf clip to install.
Page 10 of 28
Shelf
Shelf
Pillaster
Clip
(I-beam)
Horizontal Bottle Cooler Bin Divider Installation
Horizontal bottle coolers are shipped with bin dividers in place. To
adjust the spacing, see the instructions below.
NOTE: A divider positioned in front of the mechanical box
requires a specific notch cutout.
Procedure
1. Push the divider towards the rear of the cabinet to release
the front pegs from the front grommeted holes. Dividers are
spring-loaded.
2. Align the front divider pegs with the desired holes and,
starting with the bottom divider pegs, punch through the
interior tape lining of both the top and bottom holes.
NOTE: Front holes are taped over to improve insulation
values.
3. Remove the divider from the front holes. Align the regular and
spring-loaded rear divider pegs with the holes corresponding
to the desired front holes. Then, insert the rear pegs as far as
possible and maneuver the front pegs into place.
NOTE: Divider positioned in front of mechanical box requires
specific notch cut out.
04/26/2021
TEC_TM_114 | REV. A | EN
truemfg.com
Cabinet Setup (cont.)
Direct Draw Draft Arm Installation
On direct draws, the drain is located at the front of the cabinet.
To plumb in the drain, connect 3⁄4" (19.05 mm) P.V.C. pipe to the
3⁄4" (19.05 mm) barbed fitting supplied with the unit.
CO₂ Pressure
Mobile tapsters, to retain complete mobility, the CO2 tank
(up to 5 lb. (2.3 kg) in size) can be placed inside the cooler
(strap holders furnished).
Shelf
Standards
Kegerator Installation
Kit Components
Shelf
a. Hole Cover*
b. Draft Tower (Double Tower shown)
c. Rubber Gasket
d. O-Ring(s)
e. Draft Tower Hardware (x8)
f. Draft Tower Handle(s)
g. CO₂ Cylinder*
(shipped empty, fill before use)
h. Double CO₂ Pressure Regulator*
i. Beer Tappers*
j. 5/16" I.D. x 9/16" O.D. Clear Vinyl Tubing with Clamps
(36" (914.4 mm))
*TDB-1 kit only
Required Tool(s)
• Phillips Screwdriver
• Adjustable Wrench
• 1/4" Socket Wrench
• Leak Check Solution
WARNING
Take care when handling filled CO₂ tanks.
If unfamiliar with using CO₂ tanks and/or
regulators, seek information from your local
distributor or brewer representative before
proceeding.
Before You Begin (TDB-1 only)
If the application will not use the kegerator system, then, with
the provided hardware, install the hole cover over the draft
tower hole. See fig. 1.
Procedure
1. Position the rubber gasket over the mounting holes in the
cabinet counter top. See fig. 2.
2. Insert the o-rings into the beer line connectors. See fig. 3.
3. Run the beer line through the hole and into the cabinet.
See fig. 4.
4. With the provided hardware, install the draft tower.
See fig. 5.
TEC_TM_114 | REV. A | EN
U N D E R B A R R E F R I G E R A T I O N
F
B
A
C
D
Fig. 1. Install the hole cover over the draft tower hole if not using the kegerator system.
– Contents under pressure.
Fig. 2. Position the rubber gasket around
the draft tower hole.
Fig. 4. Thread the beer lines into the
cabinet.
04/26/2021
truemfg.com
G
H
J
I
E
Fig. 3. Be sure to insert the o-ring in the
beer line connector.
Fig. 5. Secure the draft tower to the
countertop.
Page 11 of 28
Hide quick links:
Advertisement
Table of Contents
