Advertisement
Quick Links
Operation Manual
Sandfilter
51792 (without pump), 51793 (with pump)
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignific -
antly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Related Manuals for WilTec 51792
Summary of Contents for WilTec 51792
- Page 1 Operation Manual Sandfilter 51792 (without pump), 51793 (with pump) Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignific - antly.
- Page 2 All rights reserved. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
- Page 3 You have to make sure that the filter is not exposed directly to sunlight. The pond pressure filter has to be horizontally fixed with screws on a suitable mounting place. © by WilTec Wildanger Technik GmbH Item 51792, 51793 Page 3 http://www.WilTec.de http://www.aoyue.eu...
- Page 4 Position the filter under consideration of the piping connections, so that it is convenient for op - erating and servicing. Ensure that the compliance label is facing the front to allow easy identification in the case of service difficulties. © by WilTec Wildanger Technik GmbH Item 51792, 51793 Page 4 http://www.WilTec.de http://www.aoyue.eu 01 2021-1...
- Page 5 3. Insert the tube with the diffuser body inside the tank as the picture shows; then place the funnel on the tank mouth and pour the quartz sand into the tank (sand wight 19 kg). © by WilTec Wildanger Technik GmbH Item 51792, 51793 Page 5 http://www.WilTec.de...
- Page 6 Ensure that solvents are not excessively applied to fittings as this could run into O-ring and • create sealing problems. Do not over-tighten fittings or adapters • © by WilTec Wildanger Technik GmbH Item 51792, 51793 Page 6 http://www.WilTec.de http://www.aoyue.eu 01 2021-1 http://www.teichtip.de...
- Page 7 Stop the pump, set the valve to FILTER and start the pump for normal filtering. WASTE To bypass filter for draining or lowering water level and for vacuuming heavy debris directly to waste. © by WilTec Wildanger Technik GmbH Item 51792, 51793 Page 7 http://www.WilTec.de http://www.aoyue.eu...
- Page 8 Name 1.25” top valve Clamp assembly O-ring Sand tank Diffusor assembly Drain plug Hose Hose clamp Hose adaptor Pump Sand filter support Gauge assembly © by WilTec Wildanger Technik GmbH Item 51792, 51793 Page 8 http://www.WilTec.de http://www.aoyue.eu 01 2021-1 http://www.teichtip.de...
- Page 9 If the leak is between the pump Water leak Leaking spot and the motor, contact the after- sales service of the pool manu- facturer. © by WilTec Wildanger Technik GmbH Item 51792, 51793 Page 9 http://www.WilTec.de http://www.aoyue.eu 01 2021-1 http://www.teichtip.de...
- Page 10 All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste.