OttLite Hampton Quick Start Manual

L
20w Hampton Floor Lamp
20H418VH-CA
INS120013 REV010912
ENGLISH

CONGRATULATIONS!

You've purchased the finest in natu-
ral lighting technology with your new
OttLite product.
®

PRODUCT REGISTRATION FORM

Please complete the enclosed Product
Registration Form and return it today
by mail, or register online by going to:
www.OttLite.com/warranty.
WARNING: To prevent electric shock,
make sure the lamp is not plugged in
until all assembly steps are complete.

LAMP ASSEMBLY

1. Make sure the lamp is not plugged
into an electrical outlet.
2. Remove the screw (H) from the upper
pole (F). Insert the upper pole (F) into the
back of the shade (G), re-insert screw (H)
and tighten using enclosed tool (I).
3. Thread the lower pole (D) into hole (C)
in the base (B) until secure.
4. Screw the upper lamp stem (A) into the
lower lamp stem (D).
5. To adjust lamp height, turn ring (E)
counter-clockwise to loosen. Adjust
upper pole to desired height, and tighten
ring by turning clockwise.

BULB INSERTION/REPLACEMENT

1. Make sure the lamp is not plugged into
an electrical socket.
2. If the lamp has been in use, allow it
to cool for approximately five minutes
before proceeding.
SL-786 CAUTION!
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer
or its service agent or a similar qualified person in order to avoid a hazard. Indoor use only.
Hampton Floor Lamp
CAUTION! IMPORTANT SAFETY INSTRUCTIONS:
3. To install a bulb in the socket, hold the
THIS PORTABLE LAMP HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER) AS A FEATURE TO
bulb (L) firmly near the base, align bulb
REDUCE THE RISK OF ELECTRIC SHOCK. THIS PLUG WILL FIT IN A POLARIZED OUTLET ONLY ONE WAY. IF THE
pins with matching pin-holes then push
it straight into the socket until it "snaps"
PLUG DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A
into place.
QUALIFIED ELECTRICIAN. NEVER USE WITH AN EXTENSION CORD UNLESS PLUG CAN BE FULLY INSERTED.
4. To remove a bulb (L) already installed
DO NOT ALTER THE PLUG.
in the lamp, grasp it firmly at the base
CAUTION:
and, using a slight rocking motion, pull it
straight out of the socket. Do not twist or
turn the bulb.
FULLY INSERT.
5. Plug the lamp into a standard 120V
socket. Your lamp is ready for use.
6. Turn lamp on or off by using rocker
switch (K).
AVERTISSEMENT! IMPORTANTES DIRECTIVES DE
Please note that in operation, OttLite
®
tubes are not dimmable.
SÉCURITÉ:
Enjoy your OttLite Hampton Floor lamp!
®
CETTE LAMPE PORTATIVE EST MUNIE D'UNE FICHE POLARISÉE (UNE LAME PLUS LARGE QUE L'AUTRE). CE
This lighting system is designed for
DISPOSITIF DE SÉCURITÉ DIMINUE LE RISQUE DE CHOCS ÉLECTRIQUES PUISQUE LA FICHE NE S'INSÈRE DANS
use with OttLite type (style number
®
LA PRISE QUE D'UN SEUL CÔTÉ. SI ELLE N'ENTRE PAS DANS LA PRISE, INVERSEZ-LA. SI ELLE N'ENTRE
SB20-M). Use of other products voids
the warranty and may result in dam-
TOUJOURS PAS, CONTACTEZ UN ÉLECTRICIEN QUALIFIÉ. N'UTILISEZ JAMAIS AVEC UNE RALLONGE SAUF SI
age to the lighting system.
LA FICHE S'INSÈRE ENTIÈREMENT. NE MODIFIEZ PAS CE DISPOSITIF DE SÉCURITÉ.
AVERTISSEMENT:
DANS LA GRANDE FENTE ET POUSSEZ JUSQU'AU BOUT.
¡ PRECAUCIÓN! INSTRUCCIONES DE SEGURIDAD
IMPORTANTES:
ESTA LÁMPARA PORTÁTIL TIENE UN ENCHUFE POLARIZADO (UNA DE SUS PATAS ES MÁS ANCHA QUE LA OTRA)
COMO CARACTERISTICA PARA REDUCIR EL RIESGO DE UNA DESCARGA ELÉCTRICA. ESTE ENCHUFE ENCAJARÁ EN
CUALQUIER TOMACORRIENTE POLARIZADO SOLO DE UNA MANERA. SI EL ENCHUFE NO CALZA COMPLETAMENTE
EN EL TOMACORRIENTE DÉLE LA VUELTA. SI AÚN NO ENCAJA, PÓNGASE EN CONTACTO CON UN ELECTRICISTA
CALIFICADO. NUNCA UTILICE UNA EXTENSIÓN A NO SER QUE EL ENCHUFE PUEDA SER TOTALMENTE
INSERTADO. NO ALTERE EL ENCHUFE.
PRECAUCIÓN:
ENCHUFE CON LA RANURA ANCHA, INSERTE TOTALMENTE.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
POUR ÉVITER LES CHOCS ÉLECTRIQUE, INSÉREZ LE BOUT LARGE DE LA FICHE
PARA PREVENIR UNA DESCARGA ELÉCTRICA, HAGA COINCIDIR LA PATA ANCHA DEL