Limited Warranty Buyer agrees if this product proves to be defective, that American Megatrends, Inc. is only obligated to replace or refund the purchase price of this product according to the terms and conditions on the warranty card enclosed with this product. American Megatrends, Inc.
Section 5 Hard Disk Utility ... 45 Hard Disk Format Utility ... 47 Auto Interleave Utility ... 49 Hard Disk Utility Error Messages ... 51 Appendix A Upgrading to 128 KB Cache ... 53 Index ... 55 Baby Screamer LC Motherboard User's Guide...
Page 4
This manual was written for the OEM to assist in the proper installation, use, and operation of the Baby Screamer LC motherboard. This manual is not meant to be read by the computer owner who purchases a computer with the Baby Screamer LC motherboard. It is assumed that you, the computer manufacturer, will use this manual as a sourcebook of information, and that parts of this manual will be included in the computer owner's manual.
D i m e n s i o n s The 80386 Baby Screamer LC is an IBM® AT®-compatible motherboard, approximately 8.6 by 13 inches. It is identical in size to a standard XT motherboard with identical mounting hole locations. The height of the board components is no more than 1½ inches.
S y s t e m M e m o r y The Baby Screamer LC can have up to 128 MB on the motherboard. The Baby Screamer LC uses 256 KB x 9, 1 MB x 9, 4 MB x 9 SIMMs, or 16 MB x 9 SIMMs (Single Inline Memory Modules).
Page 7
M a t h C o p r o c e s s o r S o c k e t The Baby Screamer LC has a socket for an optional Weitek® 3167 math coprocessor. It also has a slot for an Intel 80387, Cyrix®...
S y s t e m S u p p o r t F u n c t i o n s S y s t e m S u p p o r t F u n c t i o n s The Baby Screamer LC motherboard has the following standard AT-compatible system elements: •...
Inspect the cardboard carton for obvious damage. If damaged, call Technical Support at 404-246-8600. Leave the Baby Screamer LC motherboard in its original packing. Perform all unpacking and installation procedures on a ground connected anti-static mat. The operator should wear an anti-static wristband, grounded at the same point as the anti-static mat.
I n s t a l l a t i o n S t e p s The steps for assembling a system that uses the 80386 Baby Screamer LC motherboard are shown in the following table. Each step is discussed in detail in the following pages.
S t e p 1 S e t S w i t c h a n d J u m p e r O p t i o n s S t e p 1 S e t S w i t c h a n d J u m p e r O p t i o n s Set all user-configurable jumpers and switches, and install coprocessors before installing the motherboard in the chassis.
S t e p 2 I n s t a l l M e m o r y The main memory subsystem on the Baby Screamer LC motherboard consists of two 32-bit memory banks of four SIMM (Single Inline Memory Module) sockets each. The SIMM banks accept 256 KB, 1 MB, 4 MB, or 16 MB x 9 bit SIMMs.
Page 14
S t e p 2 I n s t a l l M e m o r y , S t e p 2 I n s t a l l M e m o r y , S e l e c t i n g S I M M s S e l e c t i n g S I M M s The SIMMs must meet the following specifications:...
Page 15
SIMM will click into place. The following graphic illustrates SIMM installation. S I M M T y p e s S I M M T y p e s The graphic below shows the two types of SIMMs. Baby Screamer LC Motherboard User's Guide Continued Types of SIMM Modules...
S t e p 3 I n s t a l l C o p r o c e s s o r S t e p 3 I n s t a l l C o p r o c e s s o r The 80386 Baby Screamer LC motherboard supports the Weitek WTK3167, Intel 80387, and Cyrix compatible coprocessors.
Page 17
See the figures on the following page. Baby Screamer LC Motherboard User's Guide Continued I n t e l c o p r o c e s s o r o n t h e...
S t e p 4 I n s t a l l t h e M o t h e r b o a r d The mounting hole pattern on the Baby Screamer LC motherboard is identical to the mounting hole pattern on the IBM XT motherboard.
Page 19
Place the two mounting screws in the holes provided for them and tighten them. If necessary, shift the motherboard slightly to align the mounting holes on the motherboard with the holes on the chassis. Baby Screamer LC Motherboard User's Guide Continued Action...
S t e p 5 C o n n e c t t h e P o w e r S u p p l y S t e p 5 C o n n e c t t h e P o w e r S u p p l y The power supply should match the physical configuration of the chassis.
S t e p 6 C o n n e c t The keyboard labeled KEYBRD and AT-compatible Baby Screamer LC Motherboard User's Guide Continued t h e K e y b o a r d t h e K e y b o a r d connector is a five-pin DIN socket J1.
S t e p 7 C o n n e c t C a b l e s S t e p 7 C o n n e c t C a b l e s When connecting chassis connectors to the motherboard, connect the correct connector end. Most connector wires are color- coded.
J 8 T u r b o S w i t c h J 8 T u r b o S w i t c h J8 is a two-pin berg that connects to a bipolar hardware speed selection switch on the chassis. Baby Screamer LC Motherboard User's Guide Continued Description...
S t e p 8 I n s t a l l A d a p t e r C a r d s The 80386 Baby Screamer LC motherboard provides full compatibility with all IBM XT or AT compatible adapter cards. It has eight 16- bit expansion slots, numbered on the motherboard from SLOT1 through SLOT8.
Page 25
8 - B i t I S A S l o t P i n o u t 8 - B i t I S A S l o t P i n o u t Baby Screamer LC Motherboard User's Guide Continued IOCHCK-...
Step 9 Perform Initial Test and Configuration Review the following before powering up the system: make sure that all adapter cards are seated properly, make sure all connectors are properly installed, if the math coprocessor is used, make sure it is seated properly, make sure there are no screws or other foreign material on the motherboard, plug the system into a surge-protected power strip, and make sure blank back panels are installed on the back of the chassis to minimize RF emissions.
P O S T P h a s e s When the system is powered on, the AMIBIOS executes two types of routines: • System Test and Initialization (test and initialize motherboards for normal operations) and • System Configuration Verification (compare defined configuration with hardware actually installed).
B e e p C o d e s B e e p C o d e s Errors can occur during POST (Power On Self Test), performed every time the system is powered on. Fatal errors are communicated through a series of audible beeps. Fatal errors do not allow the system to continue the boot process. Consult the component manufacturer for possible repairs if a fatal error occurs.
The system does not halt if Wait for <F1> If Any Error in Advanced CMOS Setup is Disabled. RUN SETUP UTILITY. may also appear. Press <F1> to run AMIBIOS Setup if this message is displayed. Baby Screamer LC Motherboard User's Guide Error Message 8042 Gate-A20 Error Gate A20 on the 8042 keyboard controller is not working.
Page 30
AMIBIOS Displayed Messages, Continued Error Message HDD Controller Failure INTR Number1 Error INTR Number2 Error Invalid Boot Diskette Keyboard Is Locked...Unlock It Keyboard Error KB/Interface Error No ROM BASIC Off Board Parity Error On Board Parity Error Parity Error ???? Chapter 3 - BIOS POST Explanation system is powered down.
BIOS Identification strings. The strings contain a code that describes the BIOS options, options are explained in the AMIBIOS ISA and EISA Technical Reference. Baby Screamer LC Motherboard User's Guide Explanation Memory failed. If the memory location is known, it is displayed as xxxxx.
B I O S C o n f i g u r a t i o n S u m m a r y S c r e e n The AMIBIOS displays the following screen when the POST routines are successfully completed. AMIBIOS System Configuration (C) Copyright 1985-1991 American Megatrends Inc. Main Processor...
The AMIBIOS Standard CMOS Setup utility permits the end user to configure and set system components such as floppy drives, hard disk drives, time and date, monitor type, and keyboard. These options are described in Section 2 on page 35. Baby Screamer LC Motherboard User's Guide...
Page 34
A M I B I O S S e t u p , A M I B I O S S e t u p , A d v a n c e d C M O S S e t u p A d v a n c e d C M O S S e t u p The Advanced CMOS Setup allows the end user to configure more advanced parts of memory configuration, peripheral support, and power management support.
S t a r t i n g A M I B I O S S e t u p When POST has completed, the following message appears: Hit <DEL> if you want to run SETUP Press <Del> to run AMIBIOS Setup. Baby Screamer LC Motherboard User's Guide...
Page 36
A M I B I O S S e t u p K e y s A M I B I O S S e t u p K e y s N o t e : N o t e : The default value for <F5>, <F6>, and <F7>...
AMIBIOS Setup Main Menu BIOS SETUP PROGRAM - AMIBIOS SETUP UTILITIES (C) 1990 American Megatrends Inc., All Rights Reserved STANDARD CMOS SETUP ADVANCED CMOS SETUP AUTOCONFIGURATION WITH BIOS DEFAULTS AUTOCONFIGURATION WITH POWER ON DEFAULTS CHANGE PASSWORD HARD DISK UTILITY WRITE TO CMOS AND EXIT DO NOT WRITE TO CMOS AND EXIT Standard CMOS Setup for Changing Time, Date, Hard Disk Type, etc.
Page 38
Auto Configuration With Power-On Defaults This option configures the Power-On default settings for all BIOS options. These are worst-case settings for system performance, but are the most stable settings. Use this option as a diagnostic aid if the system is behaving erratically. Type Y and press <Enter> to use the Power-On defaults.
Move the cursor to the Date field via for each value are shown in the lower right corner of the Screen. Baby Screamer LC Motherboard User's Guide and set the hour, minute, and second by pressing <PgUp> and <PgDn> to change...
Page 40
S t a n d a r d C M O S S e t u p O p t i o n s , S t a n d a r d C M O S S e t u p O p t i o n s , H a r d D i s k D r i v e C : H a r d D i s k D r i v e C : H a r d D i s k D r i v e D :...
Page 41
H a r d D r i v e T y p e s H a r d D r i v e T y p e s Hard Drive Types Type Baby Screamer LC Motherboard User's Guide Continued Cylinders Heads...
Page 42
S t a n d a r d C M O S S e t u p O p t i o n s , S t a n d a r d C M O S S e t u p O p t i o n s , H a r d D i s k P a r a m e t e r s , cont'd H a r d D i s k P a r a m e t e r s , Not Installed is used for diskless workstations and SCSI hard disk drives.
W a r n i n g M e s s a g e W a r n i n g M e s s a g e A warning message is displayed when Advanced CMOS Setup is selected. Press any key to continue. Baby Screamer LC Motherboard User's Guide...
A d v a n c e d C M O S S e t u p S c r e e n The Advanced CMOS Setup screen is shown below. Use the AMIBIOS SETUP PROGRAM - ADVANCED CMOS SETUP (C) 1992 American Megatrends Inc., All rights reserved Typematic Rate Programming : Disabled Typematic Rate Delay (msec): 250 Typematic Rate (Chars/Sec) : 30.0...
C a c h e M e m o r y C a c h e M e m o r y This option enables or disables external cache memory. The settings are Enabled or Disabled. Baby Screamer LC Motherboard User's Guide Continued...
A d v a n c e d C M O S S e t u p O p t i o n s , A d v a n c e d C M O S S e t u p O p t i o n s , F a s t G a t e A 2 0 O p t i o n F a s t G a t e A 2 0 O p t i o n The settings are Enabled or Disabled.
The password (1 - 6 characters) is stored in CMOS RAM. To change a password, select the Change Password option from the main Setup screen and press <Enter>. The following prompt appears. Baby Screamer LC Motherboard User's Guide Enter CURRENT Password:...
Page 48
C h a n g i n g a P a s s w o r d , C h a n g i n g a P a s s w o r d , The first time this option is selected, enter a password and press <Enter>. The characters entered are not displayed. After the current password has been correctly entered, the end user is prompted for the new password.
Warning AMIBIOS Hard Disk Utilities destroy all hard disk data. Back up the data on the hard disk before running this utility. Baby Screamer LC Motherboard User's Guide T u r n t o T u r n t o...
Page 50
W h e n t o U s e A M I B I O S H a r d D i s k U t i l i t i e s W h e n t o U s e A M I B I O S H a r d D i s k U t i l i t i e s Installing a new hard disk.
The cylinders, heads and sectors formatted for each value is displayed in the activity box. It does not work on IDE or SCSI drives. Select Auto Interleave on the main Hard Disk Utility Screen and press <Enter>. The following appears. Baby Screamer LC Motherboard User's Guide Warning The Auto Interleave utility destroys hard disk data.
Page 54
A u t o I n t e r l e a v e U t i l i t y , A u t o I n t e r l e a v e U t i l i t y , The cursor is on Mark Bad Tracks.
Select Media Analysis from the main Hard Disk Utility Menu and press <Enter>. The following screen appears. The cursor is on Proceed. The warning screen appears. Press <Enter> to stop. The main Hard Disk Utility screen appears. Type Y and press <Enter> to perform the hard disk drive analysis. Baby Screamer LC Motherboard User's Guide...
Page 56
H a r d D i s k U t i l i t y E r r o r M e s s a g e s H a r d D i s k U t i l i t y E r r o r M e s s a g e s I n i t i a l i z a t i o n E r r o r s I n i t i a l i z a t i o n E r r o r s Chapter 4 AMIBIOS Setup...
Page 57
H a r d D i s k U t i l i t y E r r o r M e s s a g e s , O p e r a t i o n E r r o r s O p e r a t i o n E r r o r s Baby Screamer LC Motherboard User's Guide Continued Message...
Appendix A Appendix A Upgrading to 128 KB Cache Memory Upgrading to 128 KB Cache Memory To upgrade to 128 KB cache memory, use four 32 KB x 4 static RAM chips. These four SRAMs can be installed in either SRAM bank. The following table lists SRAM manufacturer and part numbers.
Page 59
S R A M L o c a t i o n s S R A M L o c a t i o n s Baby Screamer LC Motherboard User's Guide...