American Megatrends PMB-901LF User Manual
  1. Manuals
  2. Brands
  3. American Megatrends Manuals
  4. Motherboard
  5. PMB-901LF
  6. User manual
American Megatrends PMB-901LF User Manual

American Megatrends PMB-901LF User Manual

Intel xeon e3 v2 & 3rd gen. core i3 atx motherboard with vga/dp/audio/4com/2lan
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
USER'S
MANUAL
PMB-901LF
PMB-901LF
® ® ® ®
Intel
Xeon
Core™ i3 ATX Motherboard
With VGA/DP/Audio/4COM/2LAN
M2
® ® ® ®
rd
E3 V2 & 3
Gen.

Advertisement

Table of Contents
loading

Related Manuals for American Megatrends PMB-901LF

Summary of Contents for American Megatrends PMB-901LF

  • Page 1 USER’S MANUAL PMB-901LF ® ® ® ® ® ® ® ® Intel Xeon E3 V2 & 3 Gen. Core™ i3 ATX Motherboard With VGA/DP/Audio/4COM/2LAN PMB-901LF...
  • Page 2 Copyright Notice PMB-901LF ® ® Intel Xeon E3 V2 & 3 Gen. ™ Core i3 ATX Motherboard With VAG/DP/Audio/4COM/2LAN COPYRIGHT NOTICE & TRADEMARK All trademarks and registered trademarks mentioned herein are the property of their respective owners. This manual is copyrighted in Mar. 2013 (Revision edition: Apr. 2013). You may not reproduce or transmit in any form or by any means, electronic, or mechanical, including photocopying and recording.

  • Page 3: Copyright Notice

    Copyright Notice FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

  • Page 4: Table Of Contents

    Contents TABLE OF CONTENTS CHAPTER 1 INTRODUCTION About This Manual…............System Specification…............Safety Precautions…............CHAPTER 2 HARDWARE CONFIGURATION Jumper & Connector Quick Reference Table…....Component Locations….…..........How to Set the Jumpers…..........COM Port & Connector...………………......COM Port RI & Voltage Selection……………………….. RS-232/422/485 (COM2) Selection.……………………...
  • Page 5 Contents ® Intel Management Engine Components Utility…………. VGA Driver Utility………………………………….……. LAN Driver Utility……...........…..Sound Driver Utility……………………………………… 3-10 CHAPTER 4 AMI BIOS SETUP Introduction…..............Entering Setup…..............Main…………..............Advanced…................ Chipset…................4-39 Boot……................4-52 Security…................4-58 Save & Exit…..............4-61 Event Logs………………………………………………... 4-62 APPENDIX A EXPANSION BUS PCI Bus Connector Pin Assignment…….………………………..

  • Page 6: Chapter 1 Introduction

    CHAPTER INTRODUCTION This chapter gives you the information for PMB-901LF. It also outlines the system specifications. Sections included: About This Manual System Specifications Safety Precautions Experienced users can jump to chapter 2 on page 2-1 for a quick start. Page:1-1...

  • Page 7: About This Manual

    E3 V2 and 3 Gen. Core™ i3 ATX motherboard. The PMB-901LF provides faster processing speed, greater expandability and can handle more tasks than before. This manual is designed to assist you how to install and set up the system. It contains four chapters.

  • Page 8: System Specification

    LAN 1: Intel 82579LM (10/100/1000 Mbps) ® LAN 2: Intel 82583V (10/100/1000 Mbps) Support Wake-on-LAN High Definition; Realtek ALC888S with Mic/Line-In/Line- Audio DI/O 8 in/8 out 10 x USB 2.0, 2 x USB 3.0 Page: 1-3 ′ PMB-901LF USER S MANUAL...
  • Page 9 *Discrete graphic card is necessary for display if the chosen CPU doesn’t have integrated graphics support. Environment Operation Temp. 0 ~ 60°C (32 ~ 140°F) Storage Temp. -40 ~ 85°C (-40 ~ 185°F) Humidity Operation humidity 5 ~ 90% (non-condensing) Page: 1-4 ′ PMB-901LF USER S MANUAL...

  • Page 10: Safety Precautions

    Always disconnect power when the system is not in use. Disconnect power when you change any hardware devices. For instance, when you connect a jumper or install any cards, a surge of power may damage the electronic components or the whole system. Page: 1-5 ′ PMB-901LF USER S MANUAL...

  • Page 11: Chapter 2 Hardware Configuration

    CHAPTER HARDWARE CONFIGURATION ** QUICK START ** Helpful information describes the jumper & connector settings, and component locations. Sections included: Jumper & Connector Quick Reference Table Component Locations Configuration and Jumper settings Connector’s Pin Assignments Page 2-1...

  • Page 12: Jumper & Connector Quick Reference Table

    System Fan Connector SYS_FAN1, SYS_FAN2, SYS_FAN3, SYS_FAN4 Serial ATA Connector SATA1, SATA2, SATA3, SATA4, SATA5, SATA6, IrDA Connector Printer Port LPT1 Display Port Connector JDP1, JDP2 Digital Input/Output Connector DIO1 Audio Port AUDIO1 CPU Selection Page: 2-2 ′ PMB-901LF USER S MANUAL...

  • Page 13: Component Locations

    10 5 CPU_FAN1 ® Intel DIMM1 COM4 PCH C216 JP13 DIMM2 USBDOM1 DIMM3 USB1 DIMM4 SYS_FAN3 SATA6 SATA3 SATA1 APS1 ATX_PWR1 SATA5 SATA4 SATA2 SYS_FAN1 SYS_FAN2 USB2 PMB-901LF Front Connector, Jumper and Component locations Page: 2-3 ′ PMB-901LF USER S MANUAL...

  • Page 14: How To Set The Jumpers

    PIN1 & PIN2 to create one setting by shorting. You can either connect PIN2 & PIN3 to create another setting. The same jumper diagrams are applied all through this manual. The figure below shows what the manual diagrams look and what they represent. Page: 2-4 ′ PMB-901LF USER S MANUAL...
  • Page 15 Jumper Block looks like this JUMPER SETTINGS 2 pin Jumper close(enabled) Looks like this 3 pin Jumper 2-3 pin close(enabled) Looks like this Jumper Block 1-2 pin close(enabled) Looks like this Page: 2-5 ′ PMB-901LF USER S MANUAL...

  • Page 16: Com Port & Connector

    COM1_RTS# COM1_TX COM1_CTS# COM1 COM1_DTR# COM1_RI# COM2: COM2 Connector, selectable as RS-232/422/485 The pin assignments are as follows: ASSIGNMENT RS-232 RS-422 RS-485 COM2_DCD# 485- COM2_RX 485+ COM2_TX COM2_DTR# COM2 COM2_DSR# COM2_RTS# COM2_CTS# COM2_RI# Page: 2-6 ′ PMB-901LF USER S MANUAL...
  • Page 17 ASSIGNMENT COM3_DCD# COM3_DSR# COM3_RX COM3_RTS# COM3_TX COM3_CTS# COM3_DTR# COM3_RI# COM3/ COM4 COM4: COM4 Connector, fixed as RS-232 The pin assignments are as follows: ASSIGNMENT ASSIGNMENT COM4_DCD# COM4_DSR# COM4_RX COM4_RTS# COM4_TX COM4_CTS# COM4_DTR# COM4_RI# Page: 2-7 ′ PMB-901LF USER S MANUAL...

  • Page 18: Com Port Ri & Voltage Selection

    2-5. COM PORT RI & VOLTAGE SELECTION JP11: COM3 Port RI & Voltage Selection The pin assignments are as follows: SELECTION JUMPTER SETTING JUMPER ILLUSTRATION JP11 JP11 JP11 Note: Manufacturing default is RI. Page: 2-8 ′ PMB-901LF USER S MANUAL...
  • Page 19 Chapter 2 Hardware Configuration JP9: COM4 Port RI & Voltage Selection The pin assignments are as follows: SELECTION JUMPTER SETTING JUMPER ILLUSTRATION Note: Manufacturing default is RI. Page: 2-9 ′ PMB-901LF USER S MANUAL...

  • Page 20: Rs-232/422/485 (Com2) Selection

    JP12: RS-232/422/485 (COM2) Selection Connector, used to set COM2 function. The jumper settings are as follows: SELECTION JUMPER SETTINGS JUMPER ILLUSTRATION RS-232 All Open JP12 1-2, RS-422 3-4, 9-10 JP12 1-2, RS-485 5-6, JP12 Note: Manufacturing default is RS-232. Page: 2-10 ′ PMB-901LF USER S MANUAL...

  • Page 21: Com2 Auto Detect Selection

    Chapter 2 Hardware Configuration 2-7. COM2 AUTO DETECT SELECTION JP10: COM2 Auto Detect Selection The jumper settings are as follows: SELECTION JUMPER SETTINGS JUMPER ILLUSTRATION Normal JP10 Auto Gating JP10 Note: Manufacturing default is Normal. Page: 2-11 ′ PMB-901LF USER S MANUAL...

  • Page 22: Clear Cmos Data Selection

    CMOS” as illustrated above. After five to six seconds, set the jumper back to “Normal” and power-on the computer. 2-9. VGA PORT VGA1: VGA Port The pin assignments are as follows: ASSIGNMENT ASSIGNMENT CRTRED CRTVCC_L CRTGREEN CRTBLUE VGA1 CRTDATA HSYNC CRT_ALWAYS_ON VSYNC CRTCLK Page: 2-12 ′ PMB-901LF USER S MANUAL...

  • Page 23: Mini-Din & Usb Port

    Mini-DIN port supports keyboard, Y-cable and PS/2 mouse. The pin assignments are as follows: Mini-DIN Port: ASSIGNMENT ASSIGNMENT 5VDUAL KDAT KCLK MDAT MCLK USB Ports: ASSIGNMENT ASSIGNMENT USB10+ USB11+ USB10- USB11- VCC5 VCC5 JPS2USB1 Page: 2-13 ′ PMB-901LF USER S MANUAL...

  • Page 24: Lan & Usb Port

    Red Color On Giga LAN Speed Indicator No LAN switch/hub connected. Right Side LED Orange Color Blinking LAN Message Active No LAN Message Active USB signal: ASSIGNMENT ASSIGNMENT USB_89_VCC5 USB_89_VCC5 USBN8 USBN9 USBP8 USBP9 Page: 2-14 ′ PMB-901LF USER S MANUAL...
  • Page 25 Red Color On Giga LAN Speed Indicator No LAN switch/hub connected. Right Side LED Orange Color Blinking LAN Message Active No LAN Message Active USB signal: ASSIGNMENT ASSIGNMENT USB_1213_VCC5 USB_1213_VCC5 USBN12 USBN13 USBP12 USBP13 Page: 2-15 ′ PMB-901LF USER S MANUAL...

  • Page 26: Usb Connector

    The pin assignments are as follows: ASSIGNMENT ASSIGNMENT USB_67_VCC5 USBP7 USB_67_VCC5 USBN6 USBN7 USB1/ USBP6 USBDOM1 USBDOM1: Universal Serial Bus Connector The pin assignments are as follows: ASSIGNMENT ASSIGNMENT USB_45_VCC5 USBP5 USB_45_VCC5 USBN4 USBN5 USBP4 Page: 2-16 ′ PMB-901LF USER S MANUAL...

  • Page 27: Usb 3.0 & 2.0 Connector

    2-13. USB 3.0 & USB2.0 CONNECTOR USB2: USB3.0 & USB2.0 Connector The pin assignments are as follows: ASSIGNMENT ASSIGNMENT VCC5 USB1+ USB3_RX1_N USB1- USB2 USB3_RX1_P USB3_TX2_P USB3_TX1_N USB3_TX2_N USB3_TX1_P USB3_RX2_P USB0- USB3_RX2_N USB0+ VCC5 Page: 2-17 ′ PMB-901LF USER S MANUAL...

  • Page 28: Lan Link Led Selection

    FP2: LAN Link LED Selection The pin assignments are as follows: ASSIGNMENT ASSIGNMENT LAN1_LED+ LAN1_LED- LAN2_LED+ LAN2_LED- LAN Link LED selections are as follows: SELECTION JUMPER SETTINGS JUMPER ILLUSTRATION LAN1 LED LAN2 LED Page: 2-18 ′ PMB-901LF USER S MANUAL...

  • Page 29: Tpm Connector

    VCC5 SERIRQ LAD3 JLPC1 LAD2 CLK RUN VCC3 SUS_TAT LAD1 DREQ0 2-16. FRONT PANEL SELECTION FP1: Front Panel Selection The pin assignments are as follows: ASSIGNMENT ASSIGNMENT HDD_LED+ PWR_LED+ HDD_LED- PWR_LED- PWRBTNSW RST_BTN Page: 2-19 ′ PMB-901LF USER S MANUAL...
  • Page 30 Chapter 2 Hardware Configuration Front Panel Connector Selections are as follows: SELECTION JUMPER SETTINGS JUMPER ILLUSTRATION Hard Disk Drive LED Power LED Reset Button ATX Power Button Page: 2-20 ′ PMB-901LF USER S MANUAL...

  • Page 31: Atx Power Connector

    The pin assignments are as follows: ATX_PWR1 ASSIGNMENT ASSIGNMENT +3.3V +3.3V +3.3V -12V PSON 5VSB +12V +12V +3.3V 2-18. CPU FAN CONNECTOR CPU_FAN1: CPU Fan Connector The pin assignments are as follows: ASSIGNMENT CPU_FAN1 VCC12 FAN_TAC1 FAN_CTL1 Page: 2-21 ′ PMB-901LF USER S MANUAL...

  • Page 32: System Fan Connector

    SYS_FAN1~SYS_FAN4: System Fan Connectors The pin assignments are as follows: SYS_FAN1: ASSIGNMENT SYS_FAN1/ VCC12 SYS_FAN_IN SYS_FAN4/ SYS_FAN_CTL SYS_FAN2: ASSIGNMENT VCC12 FAN_IN1 SYS_FAN2/ FAN_CTL1 SYS_FAN3/ SYS_FAN3: ASSIGNMENT VCC12 FAN_IN2 FAN_CTL2 SYS_FAN4: ASSIGNMENT VCC12 FAN_IN3 FAN_CTL3 Page: 2-22 ′ PMB-901LF USER S MANUAL...

  • Page 33: Serial Ata Connector

    The pin assignments are as follows: SATA1: ASSIGNMENT ASSIGNMENT SATA_RXNC0 SATA1/ SATA_TXPC0 SATA_RXPC0 SATA2/ SATA_TXNC0 SATA3/ SATA4/ SATA2: ASSIGNMENT ASSIGNMENT SATA_RXNC1 SATA_TXPC1 SATA_RXPC1 SATA_TXNC1 SATA3: ASSIGNMENT ASSIGNMENT SATA_RXNC2 SATA_TXPC2 SATA_RXPC2 SATA_TXNC2 SATA4: ASSIGNMENT ASSIGNMENT SATA_RXNC3 SATA_TXPC3 SATA_RXPC3 SATA_TXNC3 Page: 2-23 ′ PMB-901LF USER S MANUAL...

  • Page 34: Irda Connector

    SATA5: ASSIGNMENT ASSIGNMENT SATA_RXNC4 SATA5/ SATA_TXPC4 SATA_RXPC4 SATA6/ SATA_TXNC4 SATA6: ASSIGNMENT ASSIGNMENT SATA_RXNC5 SATA_TXPC5 SATA_RXPC5 SATA_TXNC5 2-21. IRDA CONNECTOR IR1: IrDA (Infrared) Connector The pin assignments are as follows: ASSIGNMENT VCC5 IRRX IRTX Page: 2-24 ′ PMB-901LF USER S MANUAL...

  • Page 35: Printer Port

    Chapter 2 Hardware Configuration 2-22. PRINTER PORT LPT1: Printer Port The pin assignments are as follows: LPT1 ASSIGNMENT ASSIGNMENT AFD# PDR0 ERR# PDR1 INIT# PDR2 SLIN# PDR3 PDR4 PDR5 PDR6 PDR7 ACK# BUSY SLCT Page: 2-25 ′ PMB-901LF USER S MANUAL...

  • Page 36: Digital Input/Output Connector

    2-24. DIGITAL INPUT/OUTPUT CONNECTOR DIO1: Digital I/O Connectors The pin assignments are as follows: ASSIGNMENT ASSIGNMENT VCC5 DIN4 VCC12 DOUT4 DIN0 DIN5 DOUT0 DOUT5 DIN1 DIN6 DOUT1 DOUT6 DIN2 DIN7 DIO1 DOUT2 DOUT7 DIN3 DOUT3 Page: 2-26 ′ PMB-901LF USER S MANUAL...

  • Page 37: Audio Port

    The pin assignments are as follows: Line-In: ASSIGNMENT HD_LINE-L HD_LINE-R Line-Out: ASSIGNMENT HD_OUT-L AUDIO1 HD_OUT-R Mic-In: ASSIGNMENT HD_MIC1 HD_MIC_GND HD_MIC_VCC SPDIF (Optionally used with the same port as Lin-In): ASSIGNMENT VCC_AUD SPDIF OUT Page: 2-27 ′ PMB-901LF USER S MANUAL...

  • Page 38: Cpu Selection

    2-26. CPU SELECTION JP2: CPU Selection The jumper settings are as follows: SELECTION JUMPER SETTINGS JUMPER ILLUSTRATION ® Intel Gen. Open Core™ ® Intel Gen. Core™ ® Intel Gen. Core™ Note: Manufacturing default is Page: 2-28 ′ PMB-901LF USER S MANUAL...

  • Page 39: Chapter 3 Software Utilities

    CHAPTER SOFTWARE UTILITIES This chapter comprises the detailed information of VGA driver, LAN driver, and Sound driver. Sections included: Introduction. ® Intel Chipset Software Installation Utility ® Intel Rapid Storage Technology Utility ® Intel USB3.0 eXtensible Host Controller Utility ® Intel Management Engine Components Utility VGA Driver Utility...

  • Page 40: Introduction

    Chapter 3 Software Utilities 3-1. INTRODUCTION Enclosed with our PMB-901LF package are our driver utilities, which come in a format of CD ROM or floppy disk. Refer to the following table for driver locations: FILENAME (Assume that CD ROM drive is D:) PURPOSE ®...
  • Page 41 D:\DRIVER\Platform\Win7(64-bit)\SOUND D:\DRIVER\Platform\Win8(32-bit)\SOUND D:\DRIVER\Platform\Win8(64-bit)\SOUND D:\DRIVER\Platform\XP(32-bit)\SOUND ® D:\DRIVER\Platform\Win7(32-bit)\F6Floppy Intel F6 Floppy utility D:\DRIVER\Platform\Win7(64-bit)\F6Floppy D:\DRIVER\Platform\Win8(32-bit)\F6Floppy D:\DRIVER\Platform\Win8(64-bit)\F6Floppy D:\DRIVER\Platform\XP(32-bit)\F6Floppy D:\DRIVER\Flash BIOS Aptio (EFI) BIOS update utility Note: Be sure to install the Utility right after the OS fully installed. Page:3-3 ′ PMB-901LF USER S MANUAL...

  • Page 42: Intel Chipset Software Installation Utility

    OS installation. Please follow the steps below: Insert the driver disk into a CD ROM device. Under Windows system, go to the directory where the Utility driver is located. Run the application with administrative privileges. Page:3-4 ′ PMB-901LF USER S MANUAL...

  • Page 43: Intel Rapid Storage Technology Utility

    3-3-2. Installation of RST Driver for Windows XP/7/8 Insert the driver disk into a CD ROM device. Under Windows system, go to the directory where the RST driver is located. Run the application with administrative privileges. Page:3-5 ′ PMB-901LF USER S MANUAL...

  • Page 44: Intel Usb3.0 Extensible Host Controller Utility

    2nd generation Core™ i7 Extreme processor 3-4-2. Installation Instructions for Windows 7 Insert the driver disk into a CD ROM device. Under Windows system, go to the directory where the driver is located. Run the application with administrative privileges. Page:3-6 ′ PMB-901LF USER S MANUAL...

  • Page 45: Intel Management Engine Components Utility

    3-5-2. Installation Instructions for Windows XP/7/8 Insert the driver disk into a CD ROM device. Under Windows system, go to the directory where the driver is located. Run the application with administrative privileges. Page:3-7 ′ PMB-901LF USER S MANUAL...

  • Page 46: Vga Driver Utility

    Chapter 3 Software Utilities 3-6. VGA DRIVER UTILITY 3-6-1. Introduction The VGA interface embedded with our PMB-901LF can support a wide range of display. You can display CRT simultaneously with the same mode. 1. Win XP Series 2. Win 7 SerIes 3.

  • Page 47: Lan Driver Utility

    Chapter 3 Software Utilities 3-7. LAN DRIVER UTILITY 3-7-1. Introduction PMB-901LF is enhanced with LAN function that can support various network adapters. Installation programs for LAN drivers are listed as follows: 1. Win XP Series 2. Win 7 Series 3. Win 8 Series For more details on Installation procedure, please refer to Readme.txt file found...

  • Page 48: Sound Driver Utility

    Run the application with administrative privileges.. Follow the instructions on the screen to complete the installation. Once the installation is completed, shut down the system and restart in order for the changes to take effect. Page:3-10 ′ PMB-901LF USER S MANUAL...
  • Page 49 CHAPTER BIOS SETUP This chapter shows how to set up the AMI BIOS. Sections included: Introduction Entering Setup Main Advanced Chipset Boot Security Save & Exit Event Logs Page: 4-1...

  • Page 50: Chapter 4 Ami Bios Setup

    Chapter 4 AMI BIOS Setup 4-1. INTRODUCTION The board PMB-901LF uses an AMI Aptio BIOS that is stored in the Serial Peripheral Interface Flash Memory (SPI Flash) and can be updated. The SPI Flash contains the BIOS setup menu, Power-on Self-test (POST), the PCI auto-configuration utility, LAN EEPROM information, and Plug and Play support.
  • Page 51 The BIOS setup menu is accessible by pressing the <Del> or <F2> key on keyboard during the POST stage, right before the operating system is loading. All the settings are described in chapter to be followed. Page: 4-3 ′ PMB-901LF USER S MANUAL...

  • Page 52: Entering Setup

    As long as this message is present on the screen you may press the <Del> key to access the Setup program. In a moment, the main menu of the Aptio Setup Utility will appear on the screen: Page: 4-4 ′ PMB-901LF USER S MANUAL...
  • Page 53 You may move the cursor by up/down keys to highlight the individual menu items. As you highlight each item, a brief description of the highlighted selection will appear at the bottom of the screen. Page: 4-5 ′ PMB-901LF USER S MANUAL...

  • Page 54: Main

    Displays the current ME version. ME Firmware No changeable options Displays the current ME SKU. System Date month, day, year Specifies the current date. System Time hour, minute, second Specifies the current time. Page: 4-6 ′ PMB-901LF USER S MANUAL...

  • Page 55: Advanced

    Sub-Menu Trusted Computing settings Computing Sub-Menu CPU Configuration. Parameters. Configuration SATA Sub-Menu SATA Configuration Parameters. Configuration Intel® Rapid Sub-Menu Intel® Rapid Start Technology Start Technology settings Sub-Menu Configure Active Management Configuration Technology Parameters. Page: 4-7 ′ PMB-901LF USER S MANUAL...
  • Page 56 Monitor W83627UHG Sub-Menu System Super IO Chip Configuration. SuperIO Configuration W83627UHG Sub-Menu Monitor h/w status. H/W Monitor WatchDog Sub-Menu Watchdog timer for system reset. Configuration CPU PPM Sub-Menu CPU power management parameters. Configuration Page: 4-8 ′ PMB-901LF USER S MANUAL...
  • Page 57 Snoop - Enabled Registers Snooping. PERR# - Disabled Enables or Disables PCI Device to Generation - Enabled Generate PERR#. SERR# - Disabled Enables or Disables PCI Device to Generation - Enabled Generate SERR#. Page: 4-9 ′ PMB-901LF USER S MANUAL...
  • Page 58 OS to choose from S3 allows the platform to enter Suspend to RAM mode. S3 Video - Disabled Enable or Disable S3 Video Repost Repost - Enabled function. (for some of the Linux OS) Page: 4-10 ′ PMB-901LF USER S MANUAL...
  • Page 59 Pending TPM - None Schedule an Operation for the Operation - Enable Take Security Device. Ownership - Disable Take Ownership - TPM Clear TPM Enabled No changeable options Reports if TPM is enabled. Status Page: 4-11 ′ PMB-901LF USER S MANUAL...
  • Page 60 Chapter 4 AMI BIOS Setup BIOS Setting Options Description/Purpose TPM Active No changeable options Reports the current TPM active Status status. TPM Owner No changeable options Reports the current TPM ownership Status status. Page: 4-12 ′ PMB-901LF USER S MANUAL...
  • Page 61 No changeable options Reports the current CPU Speed Processor No changeable options Displays number of physical cores in Cores processor. Intel HT No changeable options Reports if Intel Hyper-Threading Technology Technology is supported by processor Page: 4-13 ′ PMB-901LF USER S MANUAL...
  • Page 62 CPUID functions. Set disable for WinXP. Intel - Disabled When enabled, a VMM can utilize the Virtualization - Enabled additional hardware capabilities Technology provided by Vanderpool Technology (VT). Page: 4-14 ′ PMB-901LF USER S MANUAL...
  • Page 63 RAID: Enables RAID (Redundant Array of Inexpensive Disks) function which may require installing the RAID driver during OS installation. Note that some more items shows up when select to [AHCI] or [RAID] mode. Page: 4-15 ′ PMB-901LF USER S MANUAL...
  • Page 64 Displays the drive installed on this SATA port Port5 (SATA6) 5. Shows [Empty] if no drive is installed. When select SATA Mode to [AHCI] or [RAID], it shows some more items as below: Page: 4-16 ′ PMB-901LF USER S MANUAL...
  • Page 65 Report alternate Device ID. (Note that - Enabled AHCI mode dose not support it.) Port 0/1/2/3/4/5 - Disabled Enables or disable SATA port. - Enabled Hot Plug - Disabled Designates this port as Hot Pluggable. - Enabled Page: 4-17 ′ PMB-901LF USER S MANUAL...
  • Page 66 Solid State Drive or Hard Disk Drive. Spin Up Device - Disabled On an edge detect from 0 to 1, the - Enabled PCH starts a COMRESET initialization sequence to the device. Page: 4-18 ′ PMB-901LF USER S MANUAL...
  • Page 67 OROM UI and - Disabled If enabled, then the OROM UI is BANNER - Enabled shown. Otherwise, no OROM banner or information will be displayed if all disks and RAID volumes are Normal. Page: 4-19 ′ PMB-901LF USER S MANUAL...
  • Page 68 - Enabled Technology. Technology OROM UI - 2 Seconds If enabled, indicates the delay of the Delay - 4 Seconds OROM UI Splash Screen in a normal - 6 Seconds status. - 8 Seconds Page: 4-20 ′ PMB-901LF USER S MANUAL...
  • Page 69 Entry After - 1 minute Enable RTC wake timer at S3 entry. - 2 minutes - 5 minutes - 10 minutes - 15 minutes - 30 minutes - 1 hour - 2 hours Page: 4-21 ′ PMB-901LF USER S MANUAL...
  • Page 70 Threshold from 0 to 65535 size > Active Page Threshold size in MB. When setting to zero, it will be in AUTO mode and check if partition size is enough at S3 entry. Page: 4-22 ′ PMB-901LF USER S MANUAL...
  • Page 71 MEBx Selection - Disabled OEMFLag Bit 2: Screen - Enabled Enable/Disable MEBx selection screen. Hide Un- - Disabled OEMFlag Bit 6: Configure ME - Enabled Hide Un-Configure ME without Confirmation password Confirmation Prompt Prompt Page: 4-23 ′ PMB-901LF USER S MANUAL...
  • Page 72 0 to Note. This setting only available 65535 when [WatchDog] = [Enabled] BIOS Timer multiple options Set BIOS watchdog imer. ranging from 0 to Note. This setting only available 65535 when [WatchDog] = [Enabled] Page: 4-24 ′ PMB-901LF USER S MANUAL...
  • Page 73 XHCI hand-off support. EHCI Hand-off - Disabled This is a workaround for OSes w/o - Enabled EHCI hand-off support. USB Mass - Disabled Enable/Disable USB mass storage Storage Driver - Enabled driver support. Support. Page: 4-25 ′ PMB-901LF USER S MANUAL...
  • Page 74 0 to 40 second increments seconds Mass Storage - Auto Display the device name and choose Devices - Floppy the device emulation type. <Device - Force FDD Name> - Hard Disk - CD-ROM Page: 4-26 ′ PMB-901LF USER S MANUAL...
  • Page 75 Speed System Fan3 No changeable options Displays the Sys_Fan3 speed. Speed System Fan4 No changeable options Displays the Sys_Fan4 speed. Speed VCC3.3 No changeable options Displays voltage level of the VCC3.3 in supply. Page: 4-27 ′ PMB-901LF USER S MANUAL...
  • Page 76 Set Parameters for COMB Configuration (COM2) Serial Port 2 Sub-menu Set Parameters for COMC Configuration (COM3) Serial Port 3 Sub-menu Set Parameters for COMD Configuration (COM4) Parallel Port Sub-menu Set Parameters for LPT port. Configuration Page: 4-28 ′ PMB-901LF USER S MANUAL...
  • Page 77 No changeable options Displays current settings of serial port 0. Change -Auto Select IRQ and I/O resource for the Settings -IO=3F8h; IRQ=4 serial port 0. -IO=3F8h; IRQ=3,4,5,6,7,10,11,12 -IO=2F8h; IRQ=3,4,5,6,7,10,11,12 -IO=3E8h; IRQ=3,4,5,6,7,10,11,12 -IO=2E8h; IRQ=3,4,5,6,7,10,11,12 Page: 4-29 ′ PMB-901LF USER S MANUAL...
  • Page 78 1. -IO=3F8h; IRQ=3,4,5,6,7,10,11,12 -IO=2F8h; IRQ=3,4,5,6,7,10,11,12 -IO=3E8h; IRQ=3,4,5,6,7,10,11,12 -IO=2E8h; IRQ=3,4,5,6,7,10,11,12 Device Mode - Standard Serial Port Mode Choosed the operation mode of - IrDA 1.0 (HP SIR) Mode serial port 1. Page: 4-30 ′ PMB-901LF USER S MANUAL...
  • Page 79 No changeable options Displays current settings of serial port 2. Change -Auto Select IRQ and I/O resource for the Settings -IO=3E8h; IRQ=7 serial port 2. -IO=3F8h; IRQ=3,4,5,6,7,10,11,12 -IO=2F8h; IRQ=3,4,5,6,7,10,11,12 -IO=3E8h; IRQ=3,4,5,6,7,10,11,12 -IO=2E8h; IRQ=3,4,5,6,7,10,11,12 Page: 4-31 ′ PMB-901LF USER S MANUAL...
  • Page 80 No changeable options Displays current settings of serial port 3. Change -Auto Select IRQ and I/O resource for the Settings -IO=2E8h; IRQ=10 serial port 3. -IO=3F8h; IRQ=3,4,5,6,7,10,11,12 -IO=2F8h; IRQ=3,4,5,6,7,10,11,12 -IO=3E8h; IRQ=3,4,5,6,7,10,11,12 -IO=2E8h; IRQ=3,4,5,6,7,10,11,12 Page: 4-32 ′ PMB-901LF USER S MANUAL...
  • Page 81 IRQ=5,6,7,10,11,12 -IO=3BCh; IRQ=5,6,7,10,11,12 Device Mode -STD Printer Mode Selects the mode for the parallel -SPP Mode port. Not available if the parallel port -EPP-1.9 and SPP Mode is disabled. -EPP-1.7 and SPP Mode Page: 4-33 ′ PMB-901LF USER S MANUAL...
  • Page 82 Mode -ECP and EPP 1.7 EPP is Enhanced Parallel Port Mode mode, a high-speed bi-directional mode for non-printer peripherals. ECP is Enhanced Capability Port mode, a high-speed bi-directional mode for printers and scanners. Page: 4-34 ′ PMB-901LF USER S MANUAL...
  • Page 83 No changeable options Displays voltage level of the +1.5V in supply. +1.05 No changeable options Displays voltage level of the +1.05V in supply. No changeable options Displays voltage level of the +5V in supply. Page: 4-35 ′ PMB-901LF USER S MANUAL...
  • Page 84 Chapter 4 AMI BIOS Setup BIOS Setting Options Description/Purpose 5VSB No changeable options Displays voltage level of the +VSB5 in supply. VBAT No changeable options Displays voltage level of the backup CMOS battery. Page: 4-36 ′ PMB-901LF USER S MANUAL...
  • Page 85 Chapter 4 AMI BIOS Setup 4-4-12. Advanced –Watchdog Configuration Watchdog Configuration Screen BIOS Setting Options Description/Purpose Watch Dog multiple options ranging Sets the desired value (seconds) for Timer Time- from 0 to 255 watchdog timer. Out Value Page: 4-37 ′ PMB-901LF USER S MANUAL...
  • Page 86 Chapter 4 AMI BIOS Setup 4-4-13. Advanced –CPU PPM Configuration CPU PPM Screen BIOS Setting Options Description/Purpose EIST -Disabled Enable/Disable Intel SpeedStep. -Enabled Turbo Mode -Disabled Enable/Disable CPU Turbo mode. -Enabled Page: 4-38 ′ PMB-901LF USER S MANUAL...

  • Page 87: Chipset

    Chapter 4 AMI BIOS Setup 4-5. CHIPSET Chipset screen BIOS Setting Options Description/Purpose PCH-IO Sub-menu Sets Parameter for Panther Point Configuration (South Bridge) configuration. System Agent Sub-menu Sets Parameter for Ivy Bridge (North (SA) Bridge) configuration. Configuration Page: 4-39 ′ PMB-901LF USER S MANUAL...
  • Page 88 Name Intel PCH Rev No changeable option Displays onboard PCH chip revision. PCI Express Sub-menu Configure PCH PCIE parameters Configuration Sub-menu Configure USB parameters. Configuration PCH Azalia Sub-menu Configure Azalia (HD-Audio) Configuration parameters. Page: 4-40 ′ PMB-901LF USER S MANUAL...
  • Page 89 Power Off keeps the power off till the power button is pressed. Power On makes system power on after restores AC power to the board. Last State brings system back to the last power state before AC remove. Page: 4-41 ′ PMB-901LF USER S MANUAL...
  • Page 90 Enable or disable PCI Express Clock Clock Gating - Enabled Gating for each root port. PCIe-USB - Disabled PCIe-USB Glitch W/A for bad USB Glitch W/A - Enabled device(s) connected behind PCIE/PEG Port. Page: 4-42 ′ PMB-901LF USER S MANUAL...
  • Page 91 - Disabled Enables Enhanced Host Controller - Enabled Interface 1 for high-speed USB functions (USB 2.0). EHCI 2 - Disabled Enables Enhanced Host Controller - Enabled Interface 2 for high-speed USB functions (USB 2.0). Page: 4-43 ′ PMB-901LF USER S MANUAL...
  • Page 92 Enable or disable the internal HDMI HDMI codec - Enabled codec for DP1 Port C (DP1) Azalia - Disabled Enable or disable the internal HDMI HDMI codec - Enabled codec for DP2 Port D (DP2) Page: 4-44 ′ PMB-901LF USER S MANUAL...
  • Page 93 VT-d No changeable options Display this chipset support VT-d or Capability not. Graphics Sub-menu Configure Graphic Settings. Configuration NB PCIe Sub-menu Configure IVB PCIe Settings Configuration Memory Sub-menu Memory Configuration Parameters Configuration Page: 4-45 ′ PMB-901LF USER S MANUAL...
  • Page 94 Note that select [SG] can enable both internal graphic and an external PCIe graphic at the same time, which support multi-monitor display requirement Internal - AUTO Keep IGD enabled based on the setup Graphics - Disabled options. - Enabled Page: 4-46 ′ PMB-901LF USER S MANUAL...
  • Page 95 - 32M Select DVMT 5.0 Pre-Allocated Allocated - 64M (Fixed) Graphics Memory size used by - 96M the Internal Graphics Device. - 128M - 256M - 512M LCD Control Sub-menu LCD Control Parameters. Page: 4-47 ′ PMB-901LF USER S MANUAL...
  • Page 96 BIOS Setting Options Description/Purpose Primary IGFX - CRT Select primary display device Boot Display - DP1 - DP2 Secondary - Disabled Select secondary display device IGFX Boot - CRT Display - DP1 - DP2 Page: 4-48 ′ PMB-901LF USER S MANUAL...
  • Page 97 To enable or disable the PEG. Set - Disabled Enable for always enables PEG no - Enabled matter a device on PEG or not. Detect Non- - Disabled Detect Non-Compliance PCI Express Compliance - Enabled Device in PEG. Device Page: 4-49 ′ PMB-901LF USER S MANUAL...
  • Page 98 For example, if user want to plug a Sunix PCIE-to-SATA(RAID) card on IVB x4(PCI_E2) or x16(PCI_E1) slot, it is recommended to set "Detect Non- Compliance Device" and "Enable PEG" to "Enabled" at the same time. Page: 4-50 ′ PMB-901LF USER S MANUAL...
  • Page 99 Memory - AUTO Maximum memory frequency selection Frequency - 1333 in Mhz. - 1600 ECC Support - Disabled Enable or disable DDR ECC (Error - Enabled Checking and Correction) feature or not. Page: 4-51 ′ PMB-901LF USER S MANUAL...

  • Page 100: Boot

    Sub-Menu Allow user to select boot order of Priorities available drive(s) CSM16 parameters Sub-Menu Configure Option ROM execution, boot options filters, etc. CSM parameters Sub-Menu Configure Option ROM execution, boot options filters, etc. Page: 4-52 ′ PMB-901LF USER S MANUAL...
  • Page 101 4-6-1. Boot - Hard Drive BBS Priorities Screen Hard drive BBS priorities screen BIOS Setting Options Description/Purpose Boot Option #1 - [Drive(s)] Change the boot order of available - #n - Disabled drive(s). Page: 4-53 ′ PMB-901LF USER S MANUAL...
  • Page 102 RT code is executed above 1MB. Option ROM - Force BIOS Set display mode for Option ROM Messages - Keep Current messages. INT19 Trap - Immediately BIOS reaction on INT19 trapping by Response - Postponed Option ROM. Page: 4-54 ′ PMB-901LF USER S MANUAL...
  • Page 103 Chapter 4 AMI BIOS Setup BIOS Setting Options Description/Purpose Immediate: Execute the trap right away; Postponed: Execute the trap during legacy boot. Page: 4-55 ′ PMB-901LF USER S MANUAL...
  • Page 104 OpROM policy - UEFI only Legacy PXE OpROM. - Legacy only Launch Storage - Do not launch Controls the execution of UEFI or OpROM policy - UEFI only Legacy Storage OpROM. - Legacy only Page: 4-56 ′ PMB-901LF USER S MANUAL...
  • Page 105 - Legacy only - Legacy first - UEFI first Other PCI - UEFI OpROM Select launch method for other PCI device ROM - Legacy OpROM devices, such as NIC, mass storage or priority video card. Page: 4-57 ′ PMB-901LF USER S MANUAL...

  • Page 106: Security

    Options Description/Purpose Administrator Password can be 3-20 Specifies the administrator password. Password alphanumeric characters. User Password Password can be 3-20 Specifies the user password. alphanumeric characters. HDD Security Sub-menu Set HDD password. Configuration: Page: 4-58 ′ PMB-901LF USER S MANUAL...
  • Page 107 Reports if there is security feature frozen. HDD User Pwd No changeable options Reports if there is HDD User Status Password installed. HDD Master No changeable options Reports if there is HDD Master Pwd Status Password installed. Page: 4-59 ′ PMB-901LF USER S MANUAL...
  • Page 108 Set User Password can be up to Specifies the user password. (Need Password 32 alphanumeric TPM module) characters. Set Master Password can be up to Specifies the master password. Password 32 alphanumeric characters. Page: 4-60 ′ PMB-901LF USER S MANUAL...

  • Page 109: Save & Exit

    Resets without saving any changes Changes and made in BIOS settings. Reset Restore No changeable options Loads the optimized defaults for Defaults BIOS settings. Boot Override - [Drive(s)] Forces to boot from selected [drive(s)]. Page: 4-61 ′ PMB-901LF USER S MANUAL...

  • Page 110: Event Logs

    4-9. EVENT LOGS Event Logs Screen BIOS Setting Options Description/Purpose Change Smbios Sub-menu Change the SMBIOS Even Log Event Log configuration. Settings View Smbios Sub-menu View the SMBIOS Even Log Event Log records. Page: 4-62 ′ PMB-901LF USER S MANUAL...
  • Page 111 - Do Nothing Choose options for reactions to a full Full - Erase Immediately Smbios Event Log. Log System - Disabled Choose option to enable/disable Boot Event - Enabled logging of System boot event. Page: 4-63 ′ PMB-901LF USER S MANUAL...
  • Page 112 Status Codes as OEM Codes (if not already converted to legacy). Convert OEM - Disabled Enable or disable the converting of Codes - Enabled EFI Status Codes to Standard Smbios Types (Not all may be translated). Page: 4-64 ′ PMB-901LF USER S MANUAL...
  • Page 113 Chapter 4 AMI BIOS Setup 4-9-2. EVENT LOGS - View Smbios Event Log View Smbios Event Log Screen BIOS Setting Options Description/Purpose Date/Time/Error No changeable options View the Smbios events log records. Code/Severity Page: 4-65 ′ PMB-901LF USER S MANUAL...

  • Page 114: Appendix A Expansion Bus

    EXPANSION APPENDIX This appendix indicates the pin assignments. Sections included: PCI Bus Connector Pin Assignment Page: A-1...
  • Page 115 Appendix A Expansion Bus PCI BUS CONNECTOR PIN ASSIGNMENT You will find four PCI bus connectors on PMB-901LF. The pin assignments are as follows: ASSIGNMENT ASSIGNMENT ASSIGNMENT ASSIGNMENT -12V +3.3V TRST# AD18 AD17 +12V AD16 C/BE2# +3.3V FRAME# IRDY# +3.3V...
  • Page 116 APPENDIX TECHNICAL SUMMARY This section introduce you the maps concisely. Sections included: Block Diagram Interrupt Map DMA Channel Map I/O Map Memory Map Watchdog Timer Configuration Flash BIOS Update Page: B-1...

  • Page 117: Appendix B Technical Summary

    Connector *6 High Definition Codec SPI Flash ROM ALC888S-VD2 128Mb SLOT *4 LOW PIN COUNT Parallel Serial 1/3/4 Connector TPM CONNECTOR WINBOND VRD12 Serial 2 / LPC SIO ISL6364CR IRDA Connector W83627UHG DIO 8I/8O Page: B-2 ′ PMB-901LF USER S MANUAL...

  • Page 118: Interrupt Map

    Intel(R) Active Management Technology - SOL (COM5) High Definition Audio Controller Intel(R) 7 Series/C216 Chipset Family USB Enhanced Host Controller - 1E26 Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Page: B-3 ′ PMB-901LF USER S MANUAL...
  • Page 119 Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Page: B-4 ′ PMB-901LF USER S MANUAL...
  • Page 120 Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Page: B-5 ′ PMB-901LF USER S MANUAL...
  • Page 121 Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Page: B-6 ′ PMB-901LF USER S MANUAL...
  • Page 122 Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System 4294967291 Intel(R) 82583V Gigabit Network Connection 4294967292 Intel(R) 82579LM Gigabit Network Connection 4294967293 Intel(R) USB 3.0 eXtensible Host Controller 4294967294 Intel(R) HD Graphics Page: B-7 ′ PMB-901LF USER S MANUAL...

  • Page 123: Dma Channels Map

    Appendix B Technical Summary DMA CHANNELS MAP TIMER CHANNEL ASSIGNMENT Channel 4 Direct memory access controller Page: B-8 ′ PMB-901LF USER S MANUAL...

  • Page 124: I/O Map

    Programmable interrupt controller 0x00000040-0x00000043 System timer 0x00000044-0x0000005F Motherboard resources 0x0000004E-0x0000004F Motherboard resources 0x00000050-0x00000053 System timer 0x00000060-0x00000060 Standard PS/2 Keyboard 0x00000061-0x00000061 Motherboard resources 0x00000062-0x00000063 Motherboard resources 0x00000063-0x00000063 Motherboard resources 0x00000064-0x00000064 Standard PS/2 Keyboard 0x00000065-0x0000006F Motherboard resources Page: B-9 ′ PMB-901LF USER S MANUAL...
  • Page 125 Programmable interrupt controller 0x000000A2-0x000000BF Motherboard resources 0x000000A4-0x000000A5 Programmable interrupt controller 0x000000A8-0x000000A9 Programmable interrupt controller 0x000000AC-0x000000AD Programmable interrupt controller 0x000000B0-0x000000B1 Programmable interrupt controller 0x000000B2-0x000000B3 Motherboard resources 0x000000B4-0x000000B5 Programmable interrupt controller 0x000000B8-0x000000B9 Programmable interrupt controller Page: B-10 ′ PMB-901LF USER S MANUAL...
  • Page 126 Programmable interrupt controller 0x000004D0-0x000004D1 Motherboard resources 0x00000500-0x0000057F Motherboard resources 0x00000680-0x0000069F Motherboard resources 0x00000D00-0x0000FFFF PCI bus 0x00001000-0x0000100F Motherboard resources 0x0000164E-0x0000164F Motherboard resources 0x0000E000-0x0000EFFF Intel(R) 7 Series/C216 Chipset Family PCI Express Root Port 3 - 1E14 Page: B-11 ′ PMB-901LF USER S MANUAL...
  • Page 127 ATA Storage Controller - 1E00 0x0000F130-0x0000F137 Intel(R) 7 Series/C216 Chipset Family 4 port Serial ATA Storage Controller - 1E00 0x0000F140-0x0000F147 Intel(R) Active Management Technology - SOL (COM5) 0x0000FFFF-0x0000FFFF Motherboard resources 0x0000FFFF-0x0000FFFF Motherboard resources Page: B-12 ′ PMB-901LF USER S MANUAL...

  • Page 128: Memory Map

    Intel(R) 82579LM Gigabit Network Connection 0xF7D20000-0xF7D2FFFF Intel(R) USB 3.0 eXtensible Host Controller 0xF7D30000-0xF7D33FFF High Definition Audio Controller 0xF7D35000-0xF7D350FF Intel(R) 7 Series/C216 Chipset Family SMBus Host Controller - 1E22 0xF7D36000-0xF7D363FF Intel(R) 7 Series/C216 Chipset Family USB Page: B-13 ′ PMB-901LF USER S MANUAL...
  • Page 129 0xFED18000-0xFED18FFF Motherboard resources 0xFED19000-0xFED19FFF Motherboard resources 0xFED1C000-0xFED1FFFF Motherboard resources 0xFED20000-0xFED3FFFF Motherboard resources 0xFED40000-0xFED44FFF System board 0xFED45000-0xFED8FFFF Motherboard resources 0xFED90000-0xFED93FFF Motherboard resources 0xFEE00000-0xFEEFFFFF Motherboard resources 0xFF000000-0xFFFFFFFF Intel(R) 82802 Firmware Hub Device 0xFF000000-0xFFFFFFFF Motherboard resources Page: B-14 ′ PMB-901LF USER S MANUAL...

  • Page 130: Watchdog Timer Configuration

    To exit the Extended Function Mode, writing 0xAA to the EFER is required. Once the chip exits the Extended Function Mode, it is in the normal running mode and is ready to enter the configuration mode. Page: B-15 ′ PMB-901LF USER S MANUAL...
  • Page 131 ;------ Select Logical Device 8 of watchdog timer --------------------------------------- ;------ Set second as counting unit --------------------------------------------------------- 0f5h not 08h ;------ Set timeout interval as 30seconds and start counting ------------------------- 0f6h ;------ Exit the extended function mode --------------------------------------------------- 0aah Page: B-16 ′ PMB-901LF USER S MANUAL...

  • Page 132: Flash Bios Update

    (4) Select [Boot] menu. (5) Select [Hard Drive BBS Priorities], set the USB bootable device to be the boot device. (6) Press <F4> key to save configuration and exit the BIOS setup menu. Page: B-17 ′ PMB-901LF USER S MANUAL...
  • Page 133 4. After BIOS update procedures is complete, the messages should be like the figure shown below. User can restart the system and boot up with new BIOS now. Page: B-18 ′ PMB-901LF USER S MANUAL...
  • Page 134 Appendix B Technical Summary Update is complete after restart. Verify during following boot that the BIOS version displayed at initialization screen has changed. Page: B-19 ′ PMB-901LF USER S MANUAL...

Table of Contents