Motorline professional TUB10R User& Installer's Manual
Motorline professional TUB10R User& Installer's Manual

Motorline professional TUB10R User& Installer's Manual

Advertisement

TUB
USER/INSTALLER MANUAL
Ø35 mm
20kg
TUB10R
TUB20R
TUB20
TUB20EFRA
Ø45 mm
25kg
35kg
50kg
70kg
TUB25E
TUB35E
TUB50E
TUB70E
TUB25EFRA
TUB35EFRA
TUB50EFRA
TUB70EFRA
TUB90EFRA
TUB25 24V
-
TUB50MT
-
TUB25CUT
-
-
-
TUB90M8MT
-
-
-
TUB90M8FRAMT
MANUAL DO UTILIZADOR/INSTALADOR
Ø59 mm
90kg
140kg
180kg
TUB90E
TUB140
TUB180
TUB140MT
TUB180MT
TUB90MT
Ø92 mm
200kg
300kg
TUB200R2
TUB300E
EN
v6.2
REV. 10/2020
600kg
TUB600E

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TUB10R and is the answer not in the manual?

Questions and answers

Summary of Contents for Motorline professional TUB10R

  • Page 1 REV. 10/2020 Ø35 mm Ø45 mm Ø59 mm Ø92 mm 20kg 25kg 35kg 50kg 70kg 90kg 140kg 180kg 200kg 300kg 600kg TUB10R TUB25E TUB35E TUB50E TUB70E TUB90E TUB140 TUB180 TUB200R2 TUB300E TUB600E TUB20R TUB25EFRA TUB35EFRA TUB50EFRA TUB70EFRA TUB90EFRA TUB140MT...
  • Page 2 00. CONTENT 01. SAFETY INSTRUCTIONS INDEX STANDARDS TO FOLLOW ATTENTION: 01. SAFETY INSTRUCTIONS STANDARDS TO FOLLOW This product is certified in accordance with European Community (EC) safety standards. 02. THE AUTOMATISM MOTORS MODELS AND REFERENCES This product complies with Directive 2011/65/EU of the European Parliament and of the Council, 03.
  • Page 3 MOTORS MODELS AND REFERENCES Ø Ø 59mm 18,5 35mm 15,5 39,5 31,5 61,5 C (mm) C (mm) TUB10R TUB140 230Vac 50Hz 6 Nm 26 RPM <43 dB 4 min. -25°C a 55°C 126 W 555 mm 230Vac 50Hz 80 Nm 12 RPM <50 dB...
  • Page 4 03. INSTALLATION 03. INSTALLATION PLACING THE MOTOR ON THE WALL LIMIT SWITCHES Before you start to tune the limit switches, confirm the orientation of your engine tuning arrows. This may have one or two possible orientations on the same motor: arrows going in or out. In any position, the adjustment A rotates the tube from the top to the bottom and the adjustment B rotates from the upwards.
  • Page 5 04. ADDITIONAL INFORMATION 05. TUB FRA - PROGRAMMING DISMANTLING COMPACT ACCESSORY TECHNICAL SPECIFICATIONS Disassemble the motor from • Frequency Transmission 433,92 Mhz the compact mounting ac- • Nº of Channels cessory. Just open the tabs The control board MC4SP as shown in the figure in •...
  • Page 6 05. TUB FRA - PROGRAMMING PROGRAMMING WARNING: Always start any programming with control board disconnected from the power supply! Programming new transmitter: 01 • Continuously 02 • Connect the control 03 • Keep the OPEN key 04 • After 10 sec, the press the OPEN key board to a 230V power pressed for 10 seconds,...

This manual is also suitable for:

Tub20rTub20Tub20efraTub25eTub25efraTub25 24v ... Show all

Table of Contents