Table of Contents
Advertisement
Quick Links
Access XL E and V 220V
Extra large, ceiling-recessed electric screen
Overview - Components
Hoisting Bracket
Mounting Bracket
Electrical
Cutout
Tab Tensioning
"V" Dowel
Shipping Brackets Attached
to Dowel and Screen Case
(V Screens Only)
Please Note: Shipping brackets must remain
in place until product has been mounted and
connected to power
(see Sections 1 and 4 in this
.
document.)
Also, DO NOT operate screen before removing
shipping brackets from screen case.
Read and understand all warnings
Contents
Overview - Components .......................................................................................1
PLEASE READ - Safety Information ....................................................................2
Section 2 - Hanging Access XL Case .................................................................3
Section 2.2 - Wall Installation ..................................................................................3
Section 2.1 - Ceiling Installation ..............................................................................3
Section 3 - Bottom Access XL Panel Installation/Removal ...........................4
Section 4 - Motorized Roller/Fabric Installation ..............................................4
Section 5 - Motorized Roller/Fabric Removal ...................................................5
Section 6 - Tab-Tension Adjustment Procedure ..............................................5
Section 7 - Operation............................................................................................5
Leveling Brackets
" V " F le x ib le V in y l
V ie w in g S u rf a c e
.......2
" E " F re e H a n g in g
V ie w in g S u rf a c e
CAUTION
before beginning installation.
(Page 2)
Section 8 - Electrical Connections .....................................................................5
Section 9 - Limit Adjustments .............................................................................6
Section 9.1 - Standard Motors Limit Adjustments ................................................6
Section 10 - Case Length Dimensions ...............................................................7
Section 11 - Case Width Dimensions .................................................................7
Section 12 - Mounting Bracket Dimensions .....................................................7
Section 12.1 - Ceiling Mounting Bracket.................................................................7
Section 12.2 - Wall Mounting Bracket .....................................................................7
Section 13 - Wiring Diagrams .............................................................................8
© 2021 All Rights Reserved
INSTRUCTIONS
INSTALLATION & OPERATION
Hoisting Bracket
TOOLS REQUIRED
POWER DRILL
PENCIL
LEVEL
HARDWARE
(by others)
If you have any difficulties installing or servicing your
Access XL screen, call your dealer or Draper, Inc.
Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385
draperinc.com | 765.987.7999 | 800.238.7999
|
FORM: AccessXL220V_Inst21_proof01
Mounting Bracket
Trim Flange
"E" Dowel
TAPE MEASURE
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Draper Access XL E
Summary of Contents for Draper Access XL E
-
Page 1: Table Of Contents
Section 7 - Operation....................5 If you have any difficulties installing or servicing your Access XL screen, call your dealer or Draper, Inc. Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385 draperinc.com | 765.987.7999 | 800.238.7999 FORM: AccessXL220V_Inst21_proof01 © 2021 All Rights Reserved... -
Page 2: Section 1 - Removing Shipping Brackets
3. Do not affix the unit to walls or ceilings that have inadequate strength 13. Do not wire motors in parallel without written permission from Draper, Inc. to permanently hold the unit during use. It is the owner’s and installer’s 14. -
Page 3: Section 2 - Hanging Access Xl Case
Access XL E and V 220V page 3 of 8 Section 2 - Hanging Access XL Case Figure 1-A Section 2.1 - Ceiling Installation HOISTING BRACKET not to be used for PLEASE NOTE: It is the installer’s responsibility to make sure appropriate fasteners are final installation used for mounting. -
Page 4: Section 3 - Bottom Access Xl Panel Installation/Removal
Access XL E and V 220V page 4 of 8 Section 3 - Bottom Access XL Panel Installation/Removal Bottom flange of Access housing Bottom access panel secures to the screen housing Bottom Access Panel Door with two screws , and held in the closed... -
Page 5: Section 5 - Motorized Roller/Fabric Removal
DOWEL DOWEL Section 7 - Tab-Tension Adjustment Procedure Please Note: Draper Tab-Tensioning System is factory-set, and under normal circumstances will not require field adjustments. If wrinkles are observed, follow the adjustment procedure shown in Fig. 8. PUSH & TURN PUSH & TURN... -
Page 6: Section 9 - Limit Adjustments
Access XL E and V 220V page 6 of 8 Section 9 - Limit Adjustments Figure 10 Section 9.1 - Standard Motors Limit Adjustments (Fig. 10) Please Note: Screen limits are factory set for optimum DOWN Limit (I) DOWN Limit Section 9.1.1 - "Down"... -
Page 7: Section 10 - Case Length Dimensions
Access XL E and V 220V 8 " " page 7 of 8 (206mm) (16mm) 9 " (240mm) Standard Motor Wiring is on the Section 10 - Case Length Dimensions AUDIENCE LEFT END of Screen Case. CASE LENGTH " 18"... -
Page 8: Section 13 - Wiring Diagrams
Access XL E and V 220V page 8 of 8 Section 13 - Wiring Diagrams: 220V Standard Motor Please Note: Do not wire motors in parallel. 220V Motor and Quiet Motor Single Station Control with Internal Low-Voltage Controller 220V Motor with Internal Low-Voltage Controller...
Need help?
Do you have a question about the Access XL E and is the answer not in the manual?
Questions and answers