Table of Contents
Advertisement
MAINTENANCE
WARNING
Use only original manufacturer's replacement parts,
accessories, and attachments. Failure to do so can cause
possible injury, can contribute to poor performance, and
may void your warranty.
WARNING
Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. Have the product serviced by an authorised
service centre only. When servicing, use only original
replacement parts.
■
Use gloves when maintaining the cutting means.
■
Maintain the product with care. Keep the cutter edge
sharp and clean for best performance and to reduce
the risk of injury. Follow instructions for lubricating and
changing accessories. Keep handles dry, clean, and
free from oil and grease.
■
Turn off the product and remove the battery pack
before conducting any maintenance or cleaning work.
■
After each use, clean the body and handles with a soft,
dry cloth.
■
After each use, clean the debris from the blades with a
stiff brush, and then carefully apply a rust preventative
lubricant before refitting the blade sheath. The
manufacturer recommends you use a rust preventative
and lubricant spray to apply an even distribution and
reduce the risk of personal injury from contact with
the cutter blades. For information about suitable spray
product, check with an authorised service centre.
(Warranty-approved lubricants: WD-40, INOX, and
RP7).
■
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types
of commercial solvents and may be damaged by their
use. Use clean cloths to remove dirt, dust, oil, and
grease.
■
Always ensure that the ventilation openings are kept
clear of debris.
■
Periodically inspect the cutting means for damage and
wear.
■
Always use the manufacturer's specified replacement
blades.
■
For easier operation and longer blade life, lubricate
the cutter blades before and after each use. Before
lubricating, remove the battery pack and lay cutter
blades on a flat surface. Apply lightweight machine oil
along the edge of the top blade. Do not apply oil when
the product is running.
BATTERY PROTECTION FEATURES
RYOBI 18V lithium-ion batteries are designed with features
that protect the lithium-ion cells and maximise battery life. If
4
the tool stops during use, the following may be the causes:
■
The maximum current draw of the battery has been
exceeded, causing it to automatically stop powering the
product. Release the trigger to reset the product and
pull the trigger to resume operation.
■
Excessive temperatures cause the battery to stop
powering the tool. If the battery pack is too warm, allow
it to cool down.
If the tool still does not work, recharge the battery.
NOTE: The battery pack indicator LED will not work if the
battery protection feature has caused the battery pack to
stop powering the tool. Release the tool trigger or remove
the battery pack from the tool and the battery pack LED
indicator will resume normal function.
RESIDUAL RISK
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise during use, and
the operator should pay special attention to avoid the
following:
■
injury caused by vibration
–
Hold the product by designated handles and restrict
working time and exposure.
■
injury caused by exposure to noise
Wear hearing protection and limit exposure.
–
■
injury caused by contact with the blades
–
The blade cannot be guarded while cutting. Keep
the blade away from yourself and others. Install the
blade sheath when the product is not in use.
RISK REDUCTION
It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud's Syndrome.
Symptoms may include tingling, numbness, and blanching
of the fingers, usually apparent upon exposure to cold.
Hereditary factors, exposure to cold and dampness, diet,
smoking, and work practices are all thought to contribute to
the development of these symptoms. There are measures
that can be taken by the operator to possibly reduce the
effects of vibration:
■
Keep your body warm in cold weather. When operating
the product, wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud's Syndrome.
■
After each period of operation, exercise to increase
blood circulation.
■
Take frequent work breaks. Limit the amount of
exposure per day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your physician.
WARNING
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
Advertisement
Table of Contents
