Related Manuals for Keysight N9021B MXA
Summary of Contents for Keysight N9021B MXA
- Page 1 Keysight Technologies N9021B MXA Signal Analyzer Option EXM, External Mixing Upgrade Kit Installation Note...
- Page 2 The information contained in this document is subject to change without notice. Keysight Technologies makes no warranty of any kind with regard to this material, including but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
- Page 3 Introduction This kit includes parts to upgrade a N9021B MXA signal analyzer to add Option EXM, External Mixing. This kit includes parts to upgrade a MXA regardless of frequency range option installed. In addition to installing the hardware to support Option EXM, a license for the following option will also be installed: —...
- Page 4 Option EXM, External Mixing Upgrade Kit Installation Kit Parts List Quantity Description Keysight Part Number Adapter- Coaxial Straight Female-SMA to Female-SMA, 50W 1250-1666 Washer, Lock, Internal Tooth, ¼ inch 2190-0067 Nut-Hex-Double-Chamfer 1/4-36-THD.125-IN-THK, Stainless Steel 2950-0223 50 Ohm Termination, SMA male...
- Page 5 — 5/16-inch torque wrench — ¼-inch open-end wrench — Diagonal cutters — Keysight Calibration and Adjustment Software, N7814A (revision E.25.00 or later) — Test equipment and computer supported by the X- Series Performance Tests and Adjustment Software — N9021B MXA Signal Analyzer Service Guide, N9021-90002.
-
Page 6: Analyzer Disassembly
Option EXM, External Mixing Upgrade Kit Analyzer Disassembly If the instrument is placed on its face during any of the following procedures, be sure to use a soft surface or soft cloth to avoid damage to the front panel, keys, or input connector. Make sure any adapters on the front panel are removed. - Page 7 Option EXM, External Mixing Upgrade Kit Top Brace Removal Refer to Figure 2. To remove the top brace (1), use the T-10 driver to remove the twelve screws (3) (0515-0372) attaching the top brace to the chassis. Remove the wire hold down 1 (as shown in Figure 3).
- Page 8 Option EXM, External Mixing Upgrade Kit Figure 3 Wire Hold Downs Installation Note N9021-90004...
-
Page 9: Front Frame Assembly Removal
Option EXM, External Mixing Upgrade Kit Front Frame Assembly Removal Make sure any connectors on the front panel are removed. 1. Refer to Figure 4. Using the T-10 driver, remove the eight screws (1) (0515-1035), four on each side, to detach the Front Frame Assembly from the chassis. 2. - Page 10 Option EXM, External Mixing Upgrade Kit Figure 5 Front Panel Cable Installation Note N9021-90004...
- Page 11 A13 Front End and level. Refer to Figure 6. Note that W29 is routed below W17. Torque the cable nut to 10 inch-pounds. Figure 6 Orientation of W17 in a Millimeter Wave N9021B MXA Installation Note N9021-90004...
-
Page 12: Add Ext Mixer Connector And Cable To Front Frame Assembly
Option EXM, External Mixing Upgrade Kit Add EXT MIXER Connector and Cable to Front Frame Assembly 1. Locate the SMA female to SMA female connector (1250-1666), ¼” lockwasher (2190-0067), and ¼” hex nut (2950-0223) in the kit. If the SMA connector includes hardware, discard that hardware and use the 2190-0067 lockwasher and... - Page 13 Option EXM, External Mixing Upgrade Kit Figure 8 Connecting W29 to Ext Mixer Connector Figure 9 Proper Orientation of W29 Installation Note N9021-90004...
- Page 14 Option EXM, External Mixing Upgrade Kit Front Frame Replacement 1. Refer to Figure 10. Reattach the ribbon cable W1. Ensure the locking tabs are engaged. 2. Refer to Figure 11. Carefully position the Front Frame Assembly onto the chassis. Ensure no cables are crushed.
- Page 15 Option EXM, External Mixing Upgrade Kit Figure 11 Front Frame Replacement 3. Refer to Figure 12. When the front panel is installed, cables W17 and W29 typically do not align. This is OK since the cables are flexible. 4. Refer to Figure 13.
- Page 16 Option EXM, External Mixing Upgrade Kit Figure 13 W17 and W29 Properly Aligned 5. Refer to Figure 14. Use a ¼” open-end wrench to prevent the SMA female connector on W17 from twisting. Use a 5/16” torque wrench to torque the nut on W29 to 10 inch-pounds. Figure 14 Torque Cable W29 onto W17 Installation Note N9021-90004...
- Page 17 Option EXM, External Mixing Upgrade Kit Top Brace Replacement 1. Refer to Figure 15. To replace the top brace, place the brace in the correct position and attach to the chassis using the flathead screws (3) (0515-0372). Attach the top brace to the boards using the 14 screws (15 screws with Option B5X) (4) (0515-1946) included in the kit.
- Page 18 Option EXM, External Mixing Upgrade Kit Figure 16 Wire Hold Downs 4. In the upgrade kit, locate the Warning Label, N9030-80018. 5. Refer to Figure 17. Attach the Warning Label to the top brace as shown. Figure 17 Add Warning Label to Top Brace Installation Note N9021-90004...
-
Page 19: Final Assembly
Option EXM, External Mixing Upgrade Kit Final Assembly 1. Refer to Figure 18. Slide the instrument cover back onto the deck from the rear. The seam on the cover should be on the bottom. Be sure the cover seats into the gasket groove in the Front Frame Assembly. - Page 20 USB Storage Device Configuration Menu 7. The analyzer will automatically consume the License File (this may take a few minutes). When the License File is consumed the Keysight License Manager will display a “Successful License Installation” message similar to the one shown in...
-
Page 21: Verify The License Installation
Option EXM, External Mixing Upgrade Kit Figure 20 Successful License Installation Alternate Installation Procedure The License File can be manually installed over USB or LAN by placing the license file in the following analyzer folder: C:\Program Files\Agilent\licensing. Verify the License Installation 1. - Page 22 For assistance, contact your nearest Keysight Technologies Sales and Service Office. To find your local Keysight office access the following URL, or if in the United States, call the following telephone number: http://www.keysight.com/find/assist...
- Page 23 This information is subject to change without notice. © Keysight Technologies 2021 Edition 1, January 2021 N9021-90004 www.keysight.com...