Product Presentation; Mounting Kit - CDVI SOLARPW Installation Manual

INSTALLATION MANUAL
SOLARPW-SOLARPB-STARPW-STARPB
Wiegand 125Khz Proximity Readers

1] PRODUCT PRESENTATION

Wiegand 26, 30 or 44 bit.
Direct connection.
PCB sealed in epoxy.
Audible and visual feedback.
45cm pigtail wire connection (STARPW-STARPB).
Versions available: white, black or grey.
SOLARPW-SOLARPB (L x W x D): 130 x 90 x 28mm.
STARPW-STARPB (L x W x D): 130 x 41 x 28mm.
Technology: 125 Khz.
Multi card protocol reader - Marin/HD.
Input voltage: 12V dc.
Consumption: 100mA.
Certification FCC CFR 47
CE Certification
part 15 compliance
WEEE IP53 -25°C to +70°C
2] REMINDERS AND RECOMMENDATIONS
Important Recommended cables
To protect the device 4 twisted pairs 0.6mm (AWG 24).
from back-emf, do not
forget to install the varistor Environment
across the lock terminals, When in a humid area or
in parallel. close to the sea, we recom-
mend applying varnish to the
Suggested
terminals to avoid oxidation.
power supplies
ARD12 & BS60 (in case This product is supplied
the reader is powered with a varistor.
neither by the controller The varistor must be connec-
nor by the reader controller ted directly to the locking
[INTBUSW]). system terminals (electric

3] MOUNTING KIT

Foam seal Foam seal
TF screw
SOLARPW(PB) 1 -
STARPW(PB) - 1
2
cdvigroup.com
Ref : SOLARPW-SOLARPB Ref : STARPW-STARPB
strikes, electromagnet, or
lock) operated by the device.
If the device functions with
several locking systems,
each one must be fitted with
a varistor. The varistor limits
overload produced by the
strike coil, known as self-
effect or back-emf. If you are
using a "Shear Lock", elec-
tromagnet or other type of
electric lock, we recommend
the use of a dedicated power
supply for the lock.
3x30 S5 3x8
TORX bit
®
Plastic anchor TORX ® screw
2 2 1 1
2 2 1 1
INSTALLATION MANUAL
EN
SOLARPW-SOLARPB-STARPW-STARPB
Wiegand 125Khz Proximity Readers
4] MOUNTING
Make sure that there are no pieces missing from the mounting kit. Use the correct tools according to the installa-
tion (drill, screwdrivers, tape measure,...) and follow the mounting instructions of the reader.
Ref: SOLARPW-SOLARPB
1
1 Measure and mark the center lines to determine the
reader position. Drill the fixing screw holes (Diameter:
5mm). Drill the wiring access area (Diameter: 15mm).
For optimal
illumination,
do not fold
the cable
inside the
product.
3
Varistor
1
3 Insert the plastic plugs in the mounting holes, connect the cable (refer to wiring diagram on page 11), then fasten
1
the reader with the TORX
lock (refer to page 8 "Reminders and recommendations").
Foam seal
2
Sch. a
2 Place the foam seal at the back of the reader. Take
care to begin from the bottom. (Sch. a). The foam seal
must be visible (about 2mm) on the top-back of the rea-
der (Sch. b).
screw using the TORX bit (Sch. c). Make sure that the varistor is connected across the
® ®
EN
Sch. b
fig. c
Sch. c
3
cdvigroup.com