High-quality 720p hd hybrid rapid dome camera (2 pages)
Summary of Contents for Sony SNC-Z20N
Page 1
NETWORK CAMERA SNC-Z20N SNC-Z20P SERVICE MANUAL 1st Edition...
Page 2
Lever het apparaat aan het einde van de levensduur in voor recycling, de batterij zal dan op correcte wijze verwerkt worden. When using a modular jack cable: For safety, do not connect to the connector for peripheral device wiring that might have excessive voltage. SNC-Z20N/Z20P (E)
3-797-092-11 (German, Italian, Chinese: ZNC-Z20P only) This manual describes the information on installing the SNC-Z20N/Z20P..“User’s Guide” CD-ROM (Supplied with the SNC-Z20N/Z20P) Part number: 3-809-908-02 This manual describes the information required for the proper operation and application of this unit.
AC-217 board is not described. SY-310 board In this manual, this power module is represented as follows: In text: Power module Names of repair parts: CONVERTER, DC-DC (DC-DC converter) In diagrams: AC-217 or AC-217 BOARD SNC-Z20N/Z20P (E)
3. Install the front panel in the reverse order of steps 1 and 2. Align the four projections securely with the two holes and two grooves of the front panel when installing the front panel. B 2x4 B 2x4 Lower cover SNC-Z20N/Z20P (E)
SY-310 board in the direction shown by the arrow A. 5. Disconnect the two flexible flat cables from the connectors (CN701 and CN804) on the SY-310 board. 6. Disconnect the three harnesses from the connectors (CN702, CN801, and CN805) on the SY-310 board. SNC-Z20N/Z20P (E)
Align the projection of the CT-229 board securely with Align the two grooves of the camera block securely the hole of the chassis when installing the CT-229 with the two grooves of the chassis when installing the board. camera block. SNC-Z20N/Z20P (E)
3. Remove the rear panel. (Refer to Section 1-2-3.) 4. Remove the SY-310 board. (Refer to Section 1-3-1.) 5. Remove the two solder portions on the SY-310 board, then remove the vanadium lithium rechargeable battery. Vanadium lithium rechargeable battery (VL2330) Solder portions SY-310 board SNC-Z20N/Z20P (E)
1-6. Matching Connector/Cable Use the connectors and cables below or the equivalent when connecting a cable to the connector on the rear panel during maintenance service. Connector function name Matching connector/cable Sony part No. VIDEO OUT BNC 75Z 1-569-370-12 I/O port Wire (AWG No.28 to 22)
1. Remove the cover in the direction shown by the arrow. 2. Insert it fully with the ( marked) surface of the PC card (PC card adaptor) down. Cover PC card adaptor Put the PC card with the mark down. SNC-Z20N/Z20P (E)
. Network cable (UTP CAT5 cross cable) . Power supply: For SNC-Z20N/Z20P: 24 VAC or 12 V DC, 9 W or more For IF board: 5 V DC, 100 mA . Memory Stick (16 MB or more) .
4. Turn on the power of each equipment. the SNC-Z20N/Z20P is indicated on the screen. 5. Check that the power indicator (green) of SNC-Z20N/ Z20P is blinking (indicating the test mode). 6. Install the SNC-Z20 Modify Tool software to PC.
When the user name and password are the setting in the normal mode. changed by the administrator of customer, perform 4. Attach the lower cover to SNC-Z20N/Z20P. steps 1 to 3 in Section 2-4-7 in advance. 7. Click “ActiveX viewer” on the Welcome page. The Main Viewer page is displayed.
U-matic beat etc, should be displayed on the TV monitor. (640 x 480 images) Subject: Color bars chart plus clock When the tripod adaptor is placed on the top, the vertically flipped image (upside down) is displayed. SNC-Z20N/Z20P (E)
6. Remove the PC card adaptor with the Memory Stick from the PC card slot of SNC-Z20N/Z20P. 1. Turn off the power of SNC-Z20N/Z20P once. 2. Turn on the power of SNC-Z20N/Z20P while pressing the reset switch. 2-4-6. RS-232C Interface Check 3.
Stick, do not change the configuration of folders. 5. Turn on the power of each equipment. 6. Check that the power indicator (green) of SNC-Z20N/ Z20P is blinking (indicating the test mode). 7. Check the clock on PC is set correctly at date and time.
Page 23
Modify Tool is displayed. 7. Check the “Complete!” is indicated in Status column. 8. Click END button. 9. Turn off the power of the SNC-Z20N/Z20P and IF-954 board, and then remove the 10 wires connected to the I/O PORT of SNC-Z20N/Z20P.
1.09) or “http://192.168.0.100/home/ Preparation 14/systemlog.html” (for upgrade to ver. 1.10 and later) 1. Connect PC and the power supply for SNC-Z20N/ in address section of browser, press Enter key. When Z20P to the SNC-Z20N/Z20P according to the figure user name and password dialog box appears on the in Section 2-1-2 in the power off state.
SY-310 board correctly. board correct? (Setting value : 0 0 0 0) S602 Is CN804 on the SY-310 Replace the flexible board correctly connected to cable. CN905 on the camera block board? Replace the camera Replace the fuse. block. SNC-Z20N/Z20P (E)
(14 MHz) of VD and HD correct? Is DC IN (pins 14 to 17) 10 V of CN804 on the SY-310 board supplied to the Replace the SY-310 camera block? board. Replace the SY-310 board. Replace the flexible flat cable (22-pin). SNC-Z20N/Z20P (E)
Replace the SY-310 board. (Pattern is broken between CN804 and CN702.) Are FB501 and CN503 on the CT-229 board correctly soldered? Solder the parts that are not correctly soldered. Replace the CT-229 Replace the camera board. module. (Failure of FB501) SNC-Z20N/Z20P (E)
Are the black spots, Replace the camera white spots and flaws on module. CCD corrected? Corrected No problem. (Within specifications) * Spec.: Point defects (black spots, white spots, and flaws) are less than 5 points (pixels). SNC-Z20N/Z20P (E)
3-5. POWER indicator does not light or blink Is the image normally Refer to Section 3-1. displayed on the color monitor? Is the image normally Replace the SY-310 board. displayed on the PC? Replace the LED on the SY-310 board. SNC-Z20N/Z20P (E)
T1 on the SY-310 board T1 on the SY-310 board when the is defective. Replace T1. camera setting operation is performed from PC? *White barance, etc. It is highly likely that IC801 on the SY-310 board is defective. Replace the SY-310 board. SNC-Z20N/Z20P (E)
CN101 4pin AC-217 21pin 21pin CN103 7pin CN102 5pin POWER ON LAN DC power DC power PC CARD SLOT CN801 7pin CN805 5pin CN802 RJ45 8pin Rear panel terminal 50pin 50pin block 10pin CN602 13pin Connector for adjustment SNC-Z20N/Z20P (E)
Page 32
CONTROLLER DRIVER MAIN CPU TERMINAL BOARD CN803 TYPE II SLOT ETHER MAC (1 SLOT) CT-229 BOARD IC801 FROM VIDEO OUT AC-217 BOARD IC602 + 10 V SY-310 + 5 V BOARD VISCA1 + 3.3 V VISCA2 BT601 10BASE-T/100BASE-TX SNC-Z20N/Z20P (E)
Main CPU (IC606), Web contents, or system environmental information. The data is read and written by an SH data bus. Since the system ROM is constituted by flash memory, it can upgrade software from a PC card through a network. SNC-Z20N/Z20P (E)
(PH801) (three ports). The output signals (EXINT[02:00]) from the photocoupler are input to the interrupt controller of MJPEG control (IC703) and recognized as an interrupt signal (XSHINT[2:0]) of Main CPU (IC606). Normal setting Test mode (0, 0, 0, 0) (1, 1, 1, 0) SNC-Z20N/Z20P (E)
POWER indicator (D702) shows the power supply state and operating mode. . When D702 (green) is on: Power ON, Normal mode . When D702 (green) is blinking: Power ON, Test mode . When D702 (green) is not on: Power OFF SNC-Z20N/Z20P (E)
Page 37
In addition, for semiconductors with ID Nos., refer to the separate CD-ROM titled “Semiconductor Pin Assignments” (Sony Part No. 9-968-546-xx) that allows searching for parts by semiconductor type or ID No. The semiconductors in the manual or on the CD-ROM are listed by equivalent types.
Page 40
: HIGH-BYTE DATA BUS OTHERS : NO CONNECTION : RESEVED FOR FUTURE USE : I/O POWER SUPPLY SIGNAL SIGNAL SIGNAL SIGNAL — VPEN — — — — — BYTE — — — — — — — — — — — SNC-Z20N/Z20P (E)
Therefore, specified parts should be used in the case of replacement. 2. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts common- ality and improvement. Parts list has the present standardized repair parts.
Page 60
VECTORSCOPE SCALE Copy on a transparent sheet. <For NTSC model> Burst position <For PAL model> Burst position SNC-Z20N/Z20P (E)
Page 61
Hävitä käytetty paristo valmistajan ohjeiden Remplacer uniquement avec une batterie du même mukaisesti. type ou d’un type équivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. SNC-Z20N/Z20P (E)