About This Installation Guide Contents of this Guide This guide explains how to install an ultra-short throw projector (EB-755F/EB-750F/EB-735F/EB-725W/ EB-720) using the wall mount (ELPMB62). If the mount is not supplied with the projector, you can purchase it as an optional item.
About This Installation Guide About Replacement Installations You can replace the currently installed projector with EB-755F/EB-750F/EB-735F/EB-725W/EB-720, and then project images at the same size in the same position. Conditions for Replacement Installations When replacing the projector, check if the following conditions are met.
About This Installation Guide Example Workflow for Replacement Installations You can replace the projector using the following workflow. The mount or your projector may differ from the illustrations. For details on handling and adjusting the mount, see the Installation Guide for the projector that has already been installed or for the wall mount.
Introduction Using the Product Safely For your safety, read all the instructions in this guide before using this product. Incorrect handling that ignores instructions in this guide could damage this product or could result in personal injury or property damage. Keep this installation guide at hand for future reference.
Introduction Package Contents Confirm that you have all necessary items before beginning installation. Wall Mount Main Mount M4 x 12mm Part name End cap Adjustment unit Setting plate Wall plate Wall plate cover Hexagonal axis...
Introduction Accessories Part Name Application Template sheet Attach this to the wall before attaching the wall plate, and use it to drill neces- sary holes. Mini PC plate Attach this to the wall plate when in- stalling a mini PC or stick PC. Mini PC belt Secure the PC to the plate when at- taching a mini PC or a stick PC that can-...
Introduction Part Name Application M3 x 6 mm cross recessed Secure the mini PC plate to the wall head shoulder screws (x4) plate. Necessary Items As well as the items supplied, you also need to prepare the following screws and tools. Applicable parts Necessary items For the wall mount...
Introduction Figures of Installation Dimensions 46.5mm 100mm 500mm 500mm Caution When installing the projector, make sure there is a gap between the wall and the projector's air exhaust and intake vents. (See figure above) Leaving a gap of approximately 100 mm from the ceiling to the top of the wall plate makes it easier to install and remove the projector.
Wall mount and resist any horizontal vibration. Use M10 or 3/8 inch x 60 mm nuts and bolts. Nuts and bolts smaller than M10 or 3/8 inch x 60 mm could cause the setting plate to fall. Epson accepts no responsibility for any damage or injury caused by lack of wall strength or inadequate installation.
Page 12
If any abnormalities occur with this product, immediately disconnect the cables from the product, and then contact your local dealer or the nearest Epson service call center. Continuing to use the product in an abnormal condition could cause a fire, electric shock, or visual...
Page 13
Installing the Wall mount Warning Laser warning labels have been attached to the projector. Do not look into the laser beam emitted from the projection window while projecting. (Compliant with IEC/EN60825-1:2014) Never open any cases on the projector. Electrical voltages inside the projector can cause severe injury. Do not look directly into the projector’s light source.
Installing the Wall mount Cautions on the Installation Location of the Wall Mount Warning Do not install in a location subject to oily smoke or smoke for events. If oils and so on stick to the slide plate fixing part of the projector, the case may crack and cause the projector to fall, resulting in personal injury or property damage.
Page 15
Installing the Wall mount Caution When installing two or more projectors in parallel, leave a gap of at least 1,500 mm between the projectors. 1500mm If you cannot secure a gap of approx. 1,200 mm, install a partition to block the heat vented from the projector's air exhaust vent.
Installing the Wall mount Wall Mount Specifications Item Specification Wall mount mass (setting plate, hexagonal axis, adjustment unit, wall plate, Approx. 9.2 kg wall plate cover, end cap) Maximum load capacity Approx. 15.0 kg...
Installing the Wall mount Mini PC Installation Plate 14.7 22.7 35.2 8 x Φ5 4 x Φ3.8 145.5 21.7 Item Specification Screw holes for installing PC (VESA compliant) 75 mm x 75 mm 100 mm x 100 mm Supported PC sizes Within 150 mm x 150 mm x 44 mm Supported PC weight 0.7 kg or less Installing Accessories...
Page 22
Installing the Wall mount Installation Procedure for the Wall Mount Follow the work flow below to install the wall mount. Route the cables before installing the wall mount according to your installation environment. Check the projection distance tables to determine the installation position ( p.22) Attach the adjustment unit to the projector ( p.44)
Installing the Wall mount Attaching the Mount Determining the installation position (projection distance tables) Determine the installation position of the wall plate according to the size of the screen (S) you want to project on to. See the following figure to check the values from a to d. This is the value when the setting plate is in the middle of the wall plate (See in the following illustration).
Page 24
Installing the Wall mount See the following for the values for c and d when projecting at an aspect ratio of 16:6. (EB-755F/EB-750F/EB-735F) • c1/d1: When the Screen Position is in the center • c2/d2: When the Screen Position is at the top...
Installing the Wall mount Attaching the adjustment unit to the projector Loosen the M4 bolt on the adjustment unit, and then align the marks for each part When the position is correct, tighten the M4 bolt. Secure the adjustment unit to the base of the projector with the M4 x 12 mm bolts (x4) supplied...
Installing the Wall mount Install the wall plate on the wall Attach the template sheet to the wall Attach the template sheet according to the installation position that you confirmed using the projection distance table ( p.22). Align the center position of the screen being projected with Image Center B on the Template sheet. Drive a commercially available M10 screw into the position of the temporary screw hole for the wall plate Leave a gap of 6 mm or more between the wall and the screw head.
Page 47
Installing the Wall mount Determine the positions for the mounting holes for the wall plate From the screw holes shown in the figure below, secure at least four points for optimum balance. Drill the holes in the wall Drill diameter: 10.5 mm (M10) or 10 mm (3/8 inches) Pilot hole depth: 45 mm Anchor hole depth: 40 mm 10.5mm (M10)
Installing the Wall mount Attaching the setting plate to the wall plate Loosen the M4 x 12 mm bolts (x2) and extend the arm slide on the setting plate Adjust the scale on the slider to the combined distance of the value for (b) confirmed in the projection distance table ( p.22) and the thickness of the projection surface (x).
Page 49
Installing the Wall mount Route the necessary cables through the setting plate Warning Do not hang the rest of the cable over the setting plate. They could fall and cause an accident. Make sure that cable ports for connecting to peripheral devices such as mini PCs are routed so that they come out of the lower part of the setting plate and not through walls.
Page 50
Installing the Wall mount Attach the setting plate to the wall plate Insert the hexagonal axis until the tip extends slightly out of the top of the wall plate and the other end connects to the bottom of the wall plate. Caution Take care not to trap the cables between the setting plate and wall plate.
Page 51
Installing the Wall mount Temporarily secure the setting plate Secure three points with the M6 screws supplied (x3). Rotate the bottom of the hexagonal axis with a 17 mm ratchet wrench to align the marks on the wall plate and the setting plate...
Page 52
Installing the Wall mount Tighten the M6 bolt (x1) to secure the setting plate in position...
Installing the Wall mount Attaching the adjustment unit to the setting plate Check the installation position for the adjustment unit The installation position is marked on the setting plate. Install at an appropriate position according to the size of the screen you want to project on to. •...
Installing the Wall mount Attach the adjustment unit to the setting plate with the M4 x 12 mm bolts (x4) supplied Connect the cables to the projector Connect the power cord last. Attaching peripheral devices Attaching a switcher or a tuner Use commercially available M4 screws to secure a switcher or a tuner to the screw holes as shown in the following figure.
Page 55
Installing the Wall mount Attach it so that the air exhaust vents of the PC are not blocked. We recommend installing the PC so that the air exhaust vents are at the top and the air intake vents are at the bottom. When securing with the mini PC belt Wrap the belt around the mini PC plate Secure the mini PC plate to the wall plate using the M3 x 6 mm screws (x4) supplied.
Page 56
Installing the Wall mount Place the PC on the lower edge of the mini PC plate, and secure it with the belt When securing with screws Depending on the shape of the mini PC and the orientation of the screw holes, the order in which parts are installed differs.
Turn on a projector and set the ID number for the projector in Installation > Projector ID. (When using EB-755F/EB-750F, set from Multi-Projection - Projector ID.) When you want to operate a specific projector, hold down the [ID] button on the remote control and press the button with the same number as the projector ID.
Installing the Wall mount Select the area you want to adjust and manually correct the image. This is useful when you want to make fine adjustments to the projection position after making mechanical adjustments using the guide screen. Quick Corner Arc Correction Point Correction •...
Page 59
Installing the Wall mount Use the focus lever to approximately focus the image Press the [Menu] button Using the Remote Control Using the Control Panel Select Screen Type from the Installation menu to set the aspect ratio of the projected image Change the aspect ratio if necessary Project images from a connected device, and then press the [Aspect] button on the remote control.
Installing the Wall mount Performing mechanical adjustment using the Setting Plate Installation Guide Use the guidance screen to adjust the position of the image. Press the [Menu] button Using the Remote Control Using the Control Panel Select Setting Plate Installation Guide from the Installation menu You see the guidance screen.
Page 61
Installing the Wall mount Turn the adjustment dial in the installation guide to adjust the horizontal rotation Turn the adjustment dial in the installation guide to adjust the vertical tilt Loosen the M4 bolt, and then adjust the horizontal slide...
Page 62
Installing the Wall mount Loosen the M4 bolts (x2), and then adjust the forward/backward slide Loosen the M6 bolt, and then adjust the vertical slide Re-tighten the screws and bolts that you loosened in steps 3 to 8 Warning Tighten all bolts and screws firmly. Otherwise, the product may fall and cause personal injury or property damage.
Installing the Wall mount Adjust the focus of position A in the following figure When you have finished making adjustments, press the [Esc] button on the remote control or the control panel to exit the guidance screen Adjusting using the projector menus •...
Page 64
Installing the Wall mount Select Geometry Correction from the Installation menu Select Arc Correction...
Page 65
Installing the Wall mount Select the side you want to correct and make adjustment When you reach a range that cannot be adjusted, you see the message Cannot adjust any further. displayed. When you have finished making adjustments, press the [Esc] button on the remote control or the control panel to finish adjustment Quick Corner Press the [Menu] button...
Page 66
Installing the Wall mount Select Geometry Correction from the Installation menu Select Quick Corner...
Page 67
Installing the Wall mount Select the side you want to correct and make adjustment When you reach a range that cannot be adjusted, you see the message Cannot adjust any further. displayed. While adjusting the sides, press buttons [1], [3], [7], and [9] on the remote control to select the side you want to adjust.
Page 68
Installing the Wall mount Select Geometry Correction from the Installation menu Select Point Correction Select Point Correction and then select the number of grid...
Installing the Wall mount Select the points you want to correct and make adjustment If it is hard to see the grid, use Pattern Color to change the color of the grid. When you have finished making adjustments, press the [Esc] button on the remote control or the control panel to finish adjustment Attaching the Covers Attach the left wall plate cover...
Installing the Wall mount Attach the right wall plate cover Fit the end cap to the setting plate If you are concerned about the groove in the arm, stick the supplied masking sticker. Attaching a Security Cable Perform one of the following security measures if necessary. •...
Page 71
Installing the Wall mount • Install a security wire from Kensington The security slot on this product is compatible with the Microsaver Security System manufactured by Kensington. See the following for more details on the Microsaver Security System. http://www.kensington.com/...
• Setup by connecting the computer and projector with a USB cable. • Make settings using Epson Projector Management. This guide explains the USB flash drive and the USB cable methods. For details on making settings using Epson Projector Management, see the Epson Projector Management Operation Guide. •...
Page 73
Setting the Projector Connect the USB flash drive to the projector's USB-A port • Connect the USB flash drive directly to the projector. If the USB flash drive is connected to the projector through a USB hub, the settings may not be saved correctly. •...
Setting the Projector Copying saved settings to other projectors Disconnect the power cord from the projector, and check that all of the projector's indicators have turned off Connect the USB flash drive containing the saved batch setup file to the projector's USB-A port Do not store any data except for the batch setup file on the USB flash drive.
Setting the Projector Setup by Connecting the Computer and Projector with a USB Cable The following operating systems support the batch setup function. • Windows 7 and later • OS X 10.11 and later Saving settings to a computer Disconnect the power cord from the projector, and check that all of the projector's indicators have turned off Connect the computer's USB port to the projector's USB-B1 port with a USB cable While holding down the [Esc] button on the remote control or the control panel, connect...
Setting the Projector Perform "Remove USB device" on your computer, and then disconnect the USB cable When using a Mac, perform "Remove EPSON_PJ". The projector turns off, and only the On/Standby indicator is lit blue. Copying saved settings to other projectors Disconnect the power cord from the projector, and check that all of the projector's indicators have turned off Connect the computer's USB port to the projector's USB-B1 port with a USB cable...
Writing the settings may have failed and an error may have occurred cators flashing blue, and the Laser and the in the projector's firmware. Stop using the projector, remove the Temp indicators flashing orange quickly? power plug from the electrical outlet, and contact Epson for help.
Setting the Projector Installing Multiple Projectors (Multi- Projection) You can create one horizontally long screen as a unified image projected from multiple projectors. When performing multi-projection, make connections and the necessary settings in the following order. When setting Multi-Projection, we recommend setting Operation > Sleep Mode to Off from the projector’s Menu.
Page 79
Setting the Projector Select Projector ID from the Installation menu When using EB-755F/EB-750F, select Projector ID from the Multi-Projection menu. Select the ID number for the projector Press the [Esc] button to close the menu Repeat steps 1 to 4 for the remaining projectors.
Images are not stable immediately after turning on the projector. After starting projection, wait for at least 30 minutes before adjusting the image. When using the EB-755F/EB-750F Turn on the projector Press the [Color Mode] button on the remote control, and then set the Color Mode to Multi-...
Setting the Projector Make necessary settings on the Multi-Projection menu For details on making settings, see the projector's User's Guide. Edge Blending Adjust the image overlapping section to create a seam- less image. Black Level Scale Set the magnification and splicing position for the im- age.
Appendix List of Safety Symbols The following table lists the meaning of the safety symbols labeled on the equipment. Symbol mark Approved stand- Meaning ards IEC60417 Power On No.5007 To indicate connection to the mains. IEC60417 Power Off No.5008 To indicate disconnection from the mains. IEC60417 Standby No.5009...
Page 83
Appendix Symbol mark Approved stand- Meaning ards IEC60417 Alternating current No.5032 To indicate that the equipment is suitable for alternating current only; to identify relevant terminals. IEC60417 Direct current No.5031 To indicate that the equipment is suitable for direct current only; to identify relevant terminals.
Page 84
Appendix Indication of the manufacturer and the importer in accordance with requirements of directive 2011/65/ EU (RoHS) Manufacturer: SEIKO EPSON CORPORATION Address: 3-5, Owa 3-chome, Suwa-shi, Nagano-ken 392-8502 Japan Telephone: 81-266-52-3131 http://www.epson.com/ Importer: SEIKO EUROPE B.V. Address: Azië building, Atlas ArenA, Hoogoorddreef 5, 1101 BA Amster-...